• Energy Research
• 7. Clean energy close
• IT close
• CA close
• Aurora Universities Network close

This paper presents a one-dimensional finite-volume model of an unglazed photovoltaic/thermal (PVT) solar collector. The unit consists of a conventional solar photovoltaic (PV) collector coupled with a suitable heat exchanger. In particular, the collector includes a roll bond heat exchanger and it is not equipped with back and frame insulation. The system is discretized along the flow direction (longitudinal) of the cogenerative collector. For each finite-volume element of the discretized computational domain, mass and energy balances are implemented. The collector geometry and materials parameters are taken from a commercially available device. An on-field experimental investigation is performed in order to validate the proposed model. The model is used to evaluate both electrical and thermodynamic parameters for each element of the domain and for fixed operating conditions. Finally, a sensitivity analysis is also performed in order to investigate the energetic performance of the cogenerative collector as a function of the main design/environmental parameters.

Efficiency of energy resource use is a key factor for a sustainable energy future. By matching the exergy levels of supply and demand, Energy Quality Management (EQM) of building energy supply systems may achieve more efficient use of energy resources. Beyond this, environmental impact of energy supply systems is another essential issue. This work addresses the influence of EQM on CO 2 emissions in the operation optimization of a Distributed Energy System (DES). A multi-objective linear programming problem is formulated to reduce energy costs and increase the overall exergy efficiency. Total CO 2 emissions are evaluated for the optimized operation strategies of the DES. The operators of the DES can choose the operation strategy from the Pareto front, based on their priorities and also aware of effects on CO 2 emissions. Results demonstrate more efficient use of energy resources and reduction in CO 2 emissions through EQM, as compared with conventional energy supply systems.

This paper investigates the impact of the standard approximations embodied in the well-known Momentum Theory on its performance prediction capabilities. To this aim, the results of the momentum theory, which is still widely used in all Blade Element/Momentum codes for the analysis and/or design of wind turbines, are compared with those obtained with an actuator disk model based on Computational Fluid Dynamics techniques. In this method, the axisymmetric and steady Euler equations are solved with a classical finite volume approach, while the turbine effects are modelled through a set of axial and tangential body forces distributed over a disk shaped region representing the rotor swept surface. Since this method does not rely on the momentum theory simplifying assumptions, it can be suitably employed to verify the momentum theory validity. The analysis is carried out using the well documented experimental data of the National Renewable Energy Laboratory Phase VI wind turbine.

Dolomite-based binders are characterised by interesting technical and environmental features. For their synthesis, sources of both CaO and MgO are required. The idea developed in this work is to couple the synthesis of dolomite-based binders, starting from a natural dolomite, through the concept of concentrated solar energy (needed to drive the endothermal dolomite calcination process) in fluidised bed reactors. To this end, a fluidised bed system, where the concentrated solar radiation is mimicked by the use of Xe-lamps (short-arc), has been set up and operated. Natural dolomite (sieved in the 420-590 ?m size range) was calcined at a nominal temperature of 850 °C, and bed temperature profiles during solar-driven calcination were investigated. Then, four binders were prepared by mixing slaked dolomite (obtained from the hydration of solar calcined dolomite) with either blast furnace slag or coal fly ash as supplementary cementitious materials. The binders were hydrated for curing times ranging from 7 to 56 days. X-ray fluorescence, X-ray diffraction and combined differential thermal and thermogravimetric analyses were employed as characterisation techniques both to analyse the chemical composition of starting materials and to investigate the evolution of the hydration in the four systems.

Battery participation in the service of power system frequency regulation is universally recognized as a viable means for counteracting the dramatic impact of the increasing utilization of renewable energy sources. One of the most complex aspects, in both the planning and operation stage, is the adequate characterization of the dynamic variation of the state of charge of the battery in view of lifetime preservation as well as the adequate participation in the regulation task. Since the power system frequency, which is the input of the battery regulation service, is inherently of a stochastic nature, it is easy to argue that the most proper methodology for addressing this complex issue is that of the theory of stochastic processes. In the first part of the paper, a preliminary characterization of the power system frequency is presented by showing that with an optimal degree of approximation it can be regarded as an Ornstein–Uhlenbeck process. Some considerations for guaranteeing desirable performances of the control strategy are performed by assuming that the battery-regulating power depending on the frequency can be described by means of a Wiener process. In the second part of the paper, more realistically, the regulating power due to power system changes is described as an Ornstein–Uhlenbeck or an exponential shot noise process driven by a homogeneous Poisson process depending on the frequency response features requested of the battery. Because of that, the battery state of charge is modeled as the output of a dynamic filter having this exponential shot noise process as input and its characterization constitutes the central role for the correct characterization of the battery life. Numerical simulations are carried out for demonstrating the goodness and the applicability of the proposed probabilistic approach.

In this paper a grid-tied photovoltaic (PV) cascaded H-bridge (CHB) inverter with embedded storage units is proposed. The multi-input single-output inverter architecture allows a distributed maximum power point tracking (DMPPT) approach, thus mitigating the mismatch effects. The energy storage units (ESUs) embedded at each dc-link provides more flexibility to the power circuit compensating for the inherent variability of the PV sources. The proposed power system ensures a continuous power supply to the grid also in case of PV power fluctuations due to irradiance conditions as well as to the MPPT. In particular, the presence of a storage element allows a voltage sweep on the PV source to be implemented, thus guaranteeing the maximization of PV energy harvesting, with no detrimental effect on the power delivery to the utility network. The numerical results, carried out on a single-phase nineteen-level PV CHB inverter, reveal the improved performance of the proposed design and control technique.

The safeguard of power equipments is assuming a major role in the deregulated electricity market, where a malfunctioning power system could be responsible for serious damages to a large number of system operators having access to the shared energy resource. In this context thermal monitoring of power cables represents a key issue in evaluating the risks associated with a given load management policy especially during emergency conditions. In particular this demands for reliable assessment models that should be able to predict the transient thermal behaviour when the load exceeds the nameplate value. In this connection the application of both simplified and detailed power cable thermal models is often complicated by the presence of uncertainties affecting the tolerances of the input data. The effect of these uncertainties could influence the final solution to a considerable extent. A comprehensive tolerance analysis is therefore required in order to incorporate the effect of data uncertainties into the thermal modelling process. To address this problem, in the paper the employment of interval mathematic is proposed. Several numerical results are presented and discussed in order to assess the effectiveness of the proposed methodology which offer a rough qualitative insight of the solution in a very short time, comparable to the time required for a deterministic numerical simulation.