• Energy Research
• Closed Access close
• Open Source close
• US close
• FR close
• Aurora Universities Network close

Abstract In recent years, distributed energy systems (DESs) have been recognized as a promising option for sustainable development of future energy systems, and their application has increased rapidly with supportive policies and financial incentives. With growing concerns on global warming and depletion of fossil fuels, design optimization of DESs through economic assessments for short-run benefits only is not sufficient, while application of exergy principles can improve the efficiency in energy resource use for long-run sustainability of energy supply. The innovation of this paper is to investigate exergy in DES design to attain rational use of energy resources including renewables by considering energy qualities of supply and demand. By using low-temperature sources for low-quality thermal demand, the waste of high-quality energy can be reduced, and the overall exergy efficiency can be increased. The goal of the design optimization problem is to determine types, numbers and sizes of energy devices in DESs to reduce the total annual cost and increase the overall exergy efficiency. Based on a pre-established DES superstructure with multiple energy devices such as combined heat and power and PV, a multi-objective linear problem is formulated. In modeling of energy devices, the novelty is that the entire available size ranges and the variation of their efficiencies, capital and operation and maintenance costs with sizes are considered. The operation of energy devices is modeled based on previous work on DES operation optimization. By minimizing a weighted sum of the total annual cost and primary exergy input, the problem is solved by branch-and-cut. Numerical results show that the Pareto frontier provides good balancing solutions for planners based on economic and sustainability priorities. The total annual cost and primary exergy input of DESs with optimized configurations are reduced by 21–36% as compared with conventional energy supply systems, where grid power is used for the electricity demand, and gas-fired boilers and electric chillers fed by grid power for thermal demand. A sensitivity analysis is also carried out to analyze the influence of energy prices and energy demand variation on the optimized DES configurations.

Thermal energy storage systems (TES) based on shape-stabilized phase change materials (SSPCM) designed from recycled Tetra Pak (TP) waste, paraffin wax (PW), and expanded graphite (EG) were investigated in this study. This work represents the first study to explore TP waste composed of low-density polyethylene (LDPE)/aluminum (Al) components for energy storage applications. The LDPE part serves as a matrix conserving a material in a compact, solid shape after PW melting; PW acts as an active phase change component contributing to heat absorption/release through a phase change (from a solid to a liquid state, and vice versa) of its crystalline phase. EG serves as a filler that enhances the thermal conductivity and mechanical properties of materials. The focus was put on the optimization of the composition of SSPCM including PW, and EG, to check thermal, mechanical, and rheological properties which influence the future processability of such systems through extrusion, as well as to investigate the synergic effect of graphite and residual Al component on thermal conductivity and leakage of PW. There are two main demands on polymer/PW blends, namely well-separated melting peaks for both components at significantly different temperatures, and good compatibility between polymer and PW. The best performance of SSPCM investigated in this study was found for a mixture having the composition TP/PW/EG = 50/40/10 w/w/w. This mixture shows well-balanced properties, including appropriate heat storage and release parameters, thermal conductivity, thermal diffusivity, toughness and strength, and low leakage of PW from the material. This system can store 116.2 J/g of heat energy and release 93.8 J/g of heat energy. The determination of the heat energy storage and release was performed by the transient guarded hot plate technique. Tensile testing revealed that Young's modulus of the TP/PW/EG = 50/40/10 w/w/w composition was 924 ± 71 MPa and the stress at break was 8.2 ± 1.2 MPa, which are sufficient values from the applicability ...

Abstract Predicting heat transfer is a primary task in the design of open-cell foams. When a Local Thermal Non Equilibrium (LTNE) model is employed, convection heat transfer between the solid and fluid phases is considered, and a volumetric heat transfer coefficient needs to be defined. Some recent studies pointed out that the effects of developing convection heat transfer between the fluid and the solid in a foam are to be taken into account. The developing thermal flow of air through an open-cell foam, with a uniform heat flux solid/fluid boundary condition, is investigated numerically in this paper. The geometry is modeled with reference to Kelvin's tetrakaidecahedron foam model. A correlation among the porosity, the cell diameter and the ratio of heat transfer surface to volume is derived. Three regions are identified along the flow direction: an impingement region, a thermally developing region and a thermally developed region. Dimensional and dimensionless convection heat transfer coefficients have been predicted numerically as a function of the axial coordinate of the foam, for different values of the Reynolds number and the porosity. A correlation is presented among the predicted values of the volumetric Nusselt number, the porosity, and the Reynolds number in the thermally developed region, which is in good agreement with experimental data and numerical predictions by other authors. Finally, the analysis of the convection heat transfer through a single foam cell, at a local pore-scale, is presented.

We censused primate populations at three non-hunted ‘terra firme’ forests of south-eastern Colombian Amazonia. The aggregate biomass densities of diurnal primates at all sites were amongst the lowest recorded for any non-hunted forest in western Amazonia and elsewhere in the Neotropics. Densities of red howler monkeys were low, as is typical in Amazonian terra firme forests far removed from white-water rivers, and densities of woolly monkeys were 1.5–3.5 times lower than those estimated for this species in central-western Brazilian Amazonia. Densities of small to mid-sized primates except for brown capuchins (Cebus apella) and white-faced capuchins (Cebus albifrons) were similar to those of other oligotrophic Amazonian forest sites. Our results are in agreement with other studies showing that terra firme forests of lowland Amazonia typically sustain a low biomass density of primates and other mid-sized to large vertebrates. Large reserves are therefore required to assure the viability of primate populations in oligotrophic systems. Given the escalating negative impacts of human habitat disturbance and hunting in Colombian Amazonia, we urge that a baseline sampling protocol to quantify the abundance and distribution of the harvest-sensitive vertebrate fauna be established within protected areas and the large indigenous reserves so that conservation efforts can be defined and implemented.

Fusarium poae is one of the Fusarium species commonly detected in wheat kernels affected by Fusarium Head Blight. Fusarium poae produces a wide range of mycotoxins including nivalenol (NIV). The effect of temperature on colony growth and NIV production was investigated in vitro at 5-40 °C with 5 °C intervals. When the data were fit to a Beta equation (R2 ≥ 0.97), the optimal temperature was estimated to be 24.7 °C for colony growth and 27.5 °C for NIV production. The effects of temperature on infection incidence, fungal biomass, and NIV contamination were investigated by inoculating potted durum wheat plants at full anthesis; inoculated heads were kept at 10-40 °C with 5 °C intervals for 3 days and then at ambient temperature until ripening. Temperature significantly affected the incidence of floret infection and fungal biomass (as indicated by DNA amount) in the affected heads but did not affect NIV content in the head tissue. Inoculation of potted plants with F. poae did not reduce yield.

In this paper, statistical analysis of lightning-induced voltages on distribution lines accounting for lossy ground is proposed. The analysis is performed by means of a Monte Carlo-based probabilistic approach. It aims at deducing parametric distributions that best fit the probability density functions of the induced voltages. A lightning model based on step-function channel-base current is employed.

Several cases of fatal enterocolitis have been described in association with the use of docetaxel (DTX), and this increase in adverse events has been concomitant with a change in formulation. Indeed in 2010, a new DTX-based presentation has been introduced in the form of a single ready-to-use vial by Sanofi-Aventis, presentation also used for generics. In this study, different available formulations were compared (Sanofi 2 vials, Sanofi 1 vial, Accord Healthcare, Kabi, Hospira) in terms of composition compliance with control specifications and simulated micelle behaviour to try to determine what could be the potential causes of this problem. This work had permitted to show that all the tested products complied with specifications in terms of dosage and purity. Variations in the composition of polysorbate 80 (PS80) have been observed but are probably too small to be responsible for the toxicity found in patients. However, we identified a difference in micelle size and release kinetics probably because of doubling concentration of ethanol in new formulation. As a result, we emphasised the importance in the case of DTX of conducting bioequivalence studies as expected in European Medicines Agency (EMA) guidance to ensure patient safety, even though these formulation changes might seem minor. Therefore, further studies are needed to explore the potential role of ethanol, PS80 and the unbound fraction of DTX in the development of enterocolitis in patients treated with DTX.

Abstract This work focuses on the study of heat transfer mechanisms in composites materials which may be used for Latent Heat Thermal Energy Storage applications. These composites contain phase change material (PCM) which can absorb and release energy during thermal cycling. PCM’s used here are paraffins microencapsulated in poly(methylmethacrylate); microencapsulation avoids the flow of paraffin when it is in the liquid state. Samples with different paraffin weight fractions and particles shape and distribution were studied in this work. Scanning Electron Microscopy and Differential Scanning Calorimetry were used to determine morphology and perform measurements of phase changes temperatures, enthalpies and heat capacity respectively. Further, a periodic method (DICO) allowed measuring thermal conductivity (λ) and diffusivity (a) of the composites at temperatures below and above of the paraffin phase change from crystalline solid to isotropic liquid.