• Energy Research
• 7. Clean energy close
• 6. Clean water close
• IN close
• UA close
• Transport Research close

Purpose. In modern conditions of energy consumption growth and a rapid increase in energy prices the actual problem is the development and implementation of energy efficiency programs and resource-saving conversion in to a source to provide the needs of industry and municipal power. The paper aims to solve the urgent problem of energy saving and efficient use of fuel-energy ones and heat supply system optimization on the basis of Uman National University of Horticulture (UNUH). Methodology. The work investigated the process of heating and hot water supply in the course of 2007-2015 years. Implementation of current problems of energy saving is grounded on the scientific-practical and efficient assurance of fuel and energy usage. At the same time energy-saving technologies are viewed as a priority direction of the energy sector development, reduction of man-induced impact on the environment and as a way of improving the competitiveness of the national economy. Findings. Statistical data acquisition and analyzing of gas flow and outside air temperature for nine years was carried out. On the basis of this analysis, the problem was identified and specific targets for its solutions were set. Originality. Scientific novelty lies in solving the problem of energy saving and efficient use of fuel resources in Ukraine through the use of a systematic approach, the methodology development of efficient use of different fuels and optimization of local heating operation, applying contemporary automation and control systems. Firstly it was in detail analyzed and conducted the comprehensive assessment of various factors influence on energy conservation. It takes into account the human factor, professionalism and responsibility of the operators of boilers and their superiors, as well as the relevant control services. Practical value. For UNUH campus hybrid use of solid fuel and gas boilers was carried out. Decentralization of the university heating system has been conducted through the restoration of 350 individual heating systems in residential buildings, remote departments and campus dormitories. The conclusions propose the list of activities upon the real economy of fuel and energy resources, and measures to overcome the economic and political crisis in the country.

The paper represents the analysis, which has helped to establish the usage of gas hydrate technologies in the methane conversion. This gas could be obtained in different ways. Possibilities and sources for the gas obtaining have been demonstrated. Use of other environmentally friendly sources to support operation in such systems in terms of joint energy complex has been considered. The necessary kinetic connections to provide operational sustainability of all the constituents have been given. The approach helps evaluate quantitatively the priority of its physicochemical transformations to obtain gas hydrates artificially. It is possible to transport methane at considerable distances when it is solidified. Actually, in this case there is no necessity to build costly compressor stations and pipelines for its transportation to consumers. The approach is extremely important for mining regions as it helps prolong the operating period and working out of the abandoned and off-balance coal reserves. In this case, it is proposed to apply special gasification technologies tending to maximum methane recovery. The proposed solutions give the possibility to define the trends of our further research. They will be highlighted in the following authors’ studies.

The Danish energy system is undergoing a transition from a system based on storable fossil fuels to a system based on fluctuating renewable energy sources. At the same time, more of and more of the energy system is becoming electrified; transportation, heating and fuel usage in industry and elsewhere. This article investigates the development of the Danish energy system in a medium year 2030 situation as well as in a long-term year 2050 situation. The analyses are based on scenario development by the Danish Climate Commission. In the short term, it is investigated what the effects will be of having flexible or inflexible electric vehicles and individual heat pumps, and in the long term it is investigated what the effects of changes in the load profiles due to changing weights of demand sectors are. The analyses are based on energy systems simulations using EnergyPLAN and demand forecasting using the Helena model. The results show that even with a limited short-term electric car fleet, these will have a significant effect on the energy system; the energy system’s ability to integrated wind power and the demand for condensing power generation capacity in the system. Charging patterns and flexibility have significant effects on this. Likewise, individual heat pumps may affect the system operation if they are equipped with heat storages. The analyses also show that the long-term changes in electricity demand curve profiles have little impact on the energy system performance. The flexibility given by heat pumps and electric vehicles in the long-term future overshadows any effects of changes in hourly demand curve profiles. International Journal of Sustainable Energy Planning and Management, Vol 7 (2015)

Purpose.The railways of Ukraine have been operated the locomotives, which are both morally and physically obsolete. Therefore, to ensure the competitiveness of rail transport it is necessary to update the locomotive fleet, and first of all the fleet of electric locomotives, because electrified railways provide the greater part of passenger and freight traffic. In this connection it is of special importance to determine the optimum parameters of the nominal mode of electric rolling stock. The purpose of the work is to examine the features of solution of these problems with respect to electric locomotives. Methodology. Assuming that the limit values of traction force are determined by the conditions of wheel-rail grip, then the power of the nominal mode can be represented as the product of rated speed, estimated friction coefficient, train weight and the coefficients that represent the ratio of the estimated (starting) value of traction force to value of traction force the nominal mode and the ratio of the mass of the locomotive to the train weight. Since the mass of the train is not a constant value, there is always a surplus power of the locomotive fleet required for the mastering of a predetermined volume of transportations. Reduced overcapacity of the locomotive fleet can be achieved by introduction of the locomotives of different power, designed for driving trains of different weight that will result in increased completeness of the power use but also in difficulty in selecting of locomotives for trains in operation. The paper shows the method of calculating the optimum values of power, speed and traction force of the nominal mode. It presents the mathematical model of the relationship of traction rate, excessive capacity and power of the traction unit. Findings.It is proved that the power of the traction unit, the total fleet power requirement and the excess of power in absolute units are proportional to the speed of the nominal mode. To reduce the total power of the fleet when selecting the optimum power of the traction unit it is necessary to take into consideration the speed of the nominal mode, defined by the condition of minimization of power consumption for traction, i.e. the smallest value that enables the implementation of the given running speed and the powerredundancy level required for operation. Originality. It consists in the development of a unified algorithm for determining the optimal parameter values of the nominal mode of passenger, freight and freight-passenger electric locomotives. Practical value. The authors determined the minimization costs during production, acquisition and maintenance of electric locomotives, whose nominal mode parameters are designed according to the above procedure.

Electricity supply in India is from a centralized grid. Many parts of the country experience grid interruptions. Life cycle energy and environmental analysis has been done for a 27 kWp photovoltaic system which acts as grid backup for 3 h outage in an Indian urban residential scenario. This paper discusses energy requirements and carbon emission for a PV storage system for five different battery technologies in Indian context. This can be used as a metric for comparative analysis for new batteries, with an undeveloped market. The energy requirements for the components are quantified and are compared in terms of energy payback time (EPBT) and Net Energy Ratio (NER). All the calculations are done for Indian context. EPBT is found to be in the range of 2–4.5 years for all the systems, while NER is in the range of 6.6–2.52. NaS has the highest emission factor of 0.67 kgCO2/kWh and the least for NiCd (0.091 kgCO2/kWh). These factors can be used to select a PV battery option and to target selection of materials and systems based on the reported values.

This article addresses the problem that fluctuations in the torque of an internal combustion engine (ICE) lead to additional energy losses, as it causes fluctuations in the speed and kinetic energy of the car. These losses increase as the frequency of oscillations of the torque of the internal combustion engine approaches the frequency of free (natural oscillations) of the running gear of the car in the longitudinal direction. If there is an elastic connection between the traction force and the movement of the car, the movement of the latter can be represented as complex. At the same time, the portable movement is uniform, and the relative movement is oscillatory. This article presents the results of the study of these losses for cars with mechanical and combined electromechanical drive wheels. Analytical expressions are obtained, which allows to take into account additional energy losses including the tangential rigidity of the tire and the rigidity of the suspension in the longitudinal direction. When using a combined electromechanical drive of the drive wheels as well as in the case of a mechanical transmission of a car, the resonance is dangerous. But with the increase in the share of torque kem on the wheel generated by the electric motor, the relative additional energy losses for the movement of the car are reduced.

Solar distillation is a practical alternative for freshwater production in arid zones where seawater is abundant. The attractiveness of this approach resides in the simplicity of the solar still, equipment used to produce saline-free water for drinking, intensive agriculture, domestic use and other purposes. A solar still is an apparatus exposed to solar radiation that consists essentially of a basin with a solar collector where saline water is deposited and covered with a transparent inclined glass plate. The system operates as a greenhouse where the heated seawater evaporates and condensates on the inner surface of the cover. The distillate yield is collected in an external container. A research group in Mexico has been working for years doing research on the process of freshwater production with solar stills. Various research aspects have been addressed, among which are mathematical modeling of the physical phenomenon, practical research by building solar stills with different geometries and sizes, and the proposal of a process for mass-production manufacturing of solar stills with technology innovations. This paper is an overview of some of the most relevant results obtained by these research efforts.

In this article the following problem has been considered: ways of efficiency increase for electric drives installed at the railway machinery repair enterprises taking into account the specific conditions of technological processes.