• Energy Research
• Closed Access close
• PL close
• AT close
• EU close
• SDSN Greece close

This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 723649 Indoor environmental quality (IEQ) measurement and survey data of demonstration buildings in the hybridGEOTABS project

Vehicles with hybrid drive systems, are increasingly more often being equipped with solutions that increase the drive systems efficiency. One of such solutions is to use an increased supply voltage for electric motors of such vehicles. The battery voltage is increased several times in the inverter system in order to increase the electrical power supplied to the electric motor. This article presents possible uses of such voltage amplification (called boost) in urban traffic conditions. The tests used the latest models of vehicles with hybrid drive systems equipped with the same drive units: Lexus NX 300h and Toyota RAV4 Hybrid. The study analyses the conditions of starting such a system and the characteristics of its operation. It has been shown that the amplification of the voltage powering the electrical machinery in both vehicles occurs at high torque values. The maximum voltage amplification–almost threefold (up to 650 V) allows a two-fold increase in the torque of the drive system.

Abstract The supercritical power plant analyzed in this paper consists of the following elements: a steam turbine, a hard-coal-fired oxy-type pulverized fuel boiler, an air separation unit with a four-end-type high-temperature membrane and a carbon dioxide capture unit. The electrical power of the steam turbine is 600 MW, the live steam thermodynamic parameters are 650°C/30 MPa, and the reheated steam parameters are 670°C/6 MPa. First of all the net efficiency was calculated as functions of the oxygen recovery rate. The net efficiency was lower than the reference efficiency by 9–10.5 pp, and a series of actions were thus proposed to reduce the loss of net efficiency. A change in the boiler structure produced an increase in the boiler efficiency of 2.5–2.74 pp. The range of the optimal air compressor pressure ratio (19–23) due to the net efficiency was also determined. The integration of all installations with the steam turbine produced an increase in the gross electric power by up to 50.5 MW. This operation enabled the replacement of the steam regenerative heat exchangers with gas–water heat exchangers. As a result of these alterations, the net efficiency of the analyzed power plant was improved to 5.5 pp less than the reference efficiency.

Abstract Given the need to reduce the CO2 emissions coming from the manufacturing sector, it is important, for planning purposes, to know which countries and which manufacturing sub-sectors have the greatest potential for reducing energy use. Using data from the International Atomic Energy Agency and the United Nations Industrial Development Organization, the authors estimate trends in global decoupling of energy use and manufacturing value added, compare energy-use intensity in six country groups and estimate the potential for reducing energy use and CO2 emissions under two scenarios and compare selected sub-sector energy intensity and estimate the potential for reducing energy use CO2 emissions. The comparison of energy intensities across country groups and among countries suggests that there still remains significant potential to reduce energy use and associated CO2 emissions. The analysis of four sub-sectors in developing and transition economies also shows similar but varied potential for reducing energy use and associated CO2 emissions.

SummaryThe German government has adopted a law that requires sewage plants to go beyond the recovery of phosphorus from wastewater and to promote recycling. We argue that there is no physical global short‐ or mid‐term phosphorus scarcity. However, we also argue that there are legitimate reasons for policies such as those of Germany, including: precaution as a way to ensure future generations’ long‐term supply security, promotion of technologies for closed‐loop economics in a promising stage of technology development, and decrease in the current supply risk with a new resource pool.

Abstract Efficiency of the earth-to-air heat exchangers depends not only on their thermal performance but also on the total pressure losses that are the cost of harvesting a geothermal heat. In this paper the sensitivity analysis of the flow characteristics to the change of multi-pipe exchanger geometry is presented. Experimental investigation and CFD simulation results present total pressure losses in the considered exchangers and airflows in each branch-pipes. Considered geometrical structures varies in the number of parallel pipes, pipes length, main pipes diameters and supply type. The experimental investigations were conducted on the exchangers models in a scale 1:4. To investigate the real size exchangers, validated CFD flow performance model was used. A costless modification of heat exchanger supply-type from Z-type to U-type structure (change in air inlet location) is verified as a simple method of decreasing total pressure losses by 6–36% and improving airflow division uniformity by 11–80%. It is shown that main pipes diameter that are 1.4 times bigger than parallel pipes diameter can result in diminished total pressure losses by 56–73% and improved airflow division uniformity by 6–59%. The least significant effect on the flow characteristics has the branch-pipe length. Total pressure losses of long branch-pipes exchangers can be 15–32% higher than for short ones and the airflow division uniformity can be 8–35% higher. Results can be used for choosing the proper geometry of multi-pipe earth-to-air heat exchangers from the flow performance point of view. Presented flow characteristics can be used in detailed analysis and energy assessment of exchangers cooperating with the mechanical ventilation system in building.

Abstract The direct carbon fuel cells with solid oxide electrolyte (DC-SOFC) and anodes deposited by inject printing (EM/DCIJP) were studied. The cells were fed with carbon fuel obtained by the direct RF plasma splitting of methane. Since the (EM/DCIJP)M/DCIJP technology allows easy modification of electrode material, the effect of Cu addition to the Ni–YSZ anode was investigated. The significant improvement of the cell performance with the new anode was observed.

Human diamine oxidase (hDAO, EC 1.4.3.22) is the key enzyme in the degradation of extracellular histamine. Consumption of alcohol is a known trigger of mast cell degranulation in patients with mast cell activation syndrome. Ethanol may also interfere with enzymatic histamine degradation, but reports on the effects on DAO activity are controversial. There are also conflicting reports whether disulfiram, an FDA-approved agent in the treatment of alcohol dependence, inhibits DAO. We therefore investigated the inhibitory potential of ethanol and disulfiram and their metabolites on recombinant human DAO (rhDAO) in three different assay systems. Relevant concentrations of ethanol, acetaldehyde, and acetate did not inhibit rhDAO activity in an in vitro assay system using horseradish peroxidase (HRP) -mediated luminol oxidation. The aldehyde dehydrogenase (ALDH; EC 1.2.1.3) inhibitors cyanamide and its dimer dicyanamide also had no effect on DAO activity. In one assay system, the irreversible ALDH inhibitor disulfiram and its main metabolite diethyldithiocarbamate seemed to inhibit DAO activity. However, the decreased product formation was not due to a direct block of DAO activity but resulted from inhibition of peroxidase employed in the coupled system. Our in vitro data do not support a direct blocking effect of ethanol, disulfiram, and their metabolites on DAO activity in vivo.

Abstract Demand response aims to change the energy consumption patterns of normal customers in response to changes in price rate or incentive offers. This process reduces peak loads and in turn potentially lowers the energy cost for customers. In this study, we propose a new demand response scheme on the basis of an adaptive consumption level pricing scheme. On the one hand, this strategy encourages customers to manage their energy consumption and consequently lower their energy bill. On the other hand, it allows utilities to manage the aggregate consumption and predict load requirement. Unlike other pricing schemes, such as block tariff and time-of-use, the proposed pricing scheme can lower the energy bill of about 73% of customers, assuming that the total utility revenue is the same for all pricing schemes. On the basis of the currently available schemes in the literature, we find that the proposed method has significant advantages over other schemes in terms of fairness in charging customers.