• Energy Research
• engineering and technology close
• 7. Clean energy close
• 11. Sustainability close
• 3. Good health close
• AU close
• CA close

Production of biodiesel from yellow grease (waste cooking oil and waste animal fats) is fast emerging as a promising alternative to address the twin challenges before the biodiesel industry today-fluctuation in prices of vegetable oil and the food versus fuel debate. Yellow grease has a high percentage of free fatty acids (FFA) and proves to be an unsuitable feedstock for biodiesel production from commercially viable alkali-catalyzed production systems due to saponification problems.“Green” methodologies based on heterogeneous solid acid catalyzed reactions have the potential to simultaneously promote esterification and transesterification reactions of yellow grease to produce biodiesel without soap formation and offer easy catalyst separation without generation of toxic streams. This paper presents kinetic studies for the conversion of model yellow grease feeds to biodiesel using a heteropolyacid supported on alumina (HSiW/Al2O3) using a batch autoclave. Three model yellow grease feeds were prepared using canola oil with added FFA such as palmitic, oleic and linoleic acid. A pseudo homogeneous kinetic model for the parallel esterification and transesterification was developed. The rate constants and activation parameters for esterification and transesterification reactions for the model yellow grease feeds were determined. The rate constants for esterification are higher than the transesterification rate constants. The kinetic model was validated using the experimental biodiesel data obtained from processing a commercial yellow grease feed. The kinetic model could be used to design novel processes to convert various low-value waste oils, fats and non-food grade oils to sustainable biodiesel. Keywords: Yellow grease, Canola oil, Free fatty acids, Heteropolyacid, Kinetics for esterification and transesterification

Short-term generation scheduling is an important function in daily operational planning of power systems. It is defined as optimal scheduling of power generators over a scheduling period while respecting various generator constraints and system constraints. Objective of the problem includes costs associated with energy production, start-up cost and shut-down cost along with profits. The resulting problem is a large scale nonlinear mixed-integer optimization problem for which there is no exact solution technique available. The solution to the problem can be obtained only by complete enumeration, often at the cost of a prohibitively computation time requirement for realistic power systems. This paper presents a hybrid algorithm which combines Lagrangian Relaxation (LR) together with Evolutionary Algorithm (EA) to solve the problem in cooperative and competitive energy environments. Simulation studies were carried out on different systems containing various numbers of units. The outcomes from different algorithms are compared with that from the proposed hybrid algorithm and the advantages of the proposed algorithm are briefly discussed.

Microgrids are increasingly being used as a platform to integrate distributed generation such as renewable energy sources and (RESs) conventional sources in both grid-connected and isolated power systems. Due to the inherent intermittent nature of RESs, energy storage systems (ESSs) that can absorb fluctuations have become inevitable. Nevertheless, large capacities of ESSs increase the initial cost while small capacities lead to instabilities and increase in the cost of conventional fuels. Therefore, finding the optimal size of the ESS for a given application is essential for the reliable, efficient and economical operation of a microgrid. Once the battery size is decided, maintaining its energy at appropriate levels is essential to ensure stable and safe operation of the microgrid. This paper presents a novel expert fuzzy system - grey wolf optimization (FL-GWO) based intelligent meta-heuristic method for battery sizing and energy management. The proposed energy management operation is carried out by a Grey Wolf Optimiser (GWO) that is helped to set the membership functions and rules of the fuzzy logic expert system. The unit commitment (UC) issue, which is essential for the proper operation of the isolated microgrid, has been additionally considered in this paper. To verify the performance of the proposed method, results are compared with the rules-based method and traditional GWO algorithm. It has been proven from the results that the FL-GWO has a significant convergence property and capability to minimize the Levelized Cost Of Electricity (LCOE) by 14.13% and 24.15% compared with conventional GWO algorithm and rules-based method, respectively. The weather conditions for different climates is used to verify the performance of the intelligent energy management method under different operating scenarios. The results show that the intelligent online multi-objective energy management strategy is capable of managing a smooth power flow with the same optimal configuration in the isolated microgrid, minimising the fossil fuel utilisation and reducing the CO2 emission level.

Abstract Global hydropower growth continues to accelerate with 25% of total capacity installed in just the last 10 years. This accelerating expansion and the important storage facility hydropower means it is increasingly important to understand the reasons for operational failures. This is a challenge because the major reason for failures involves the complex interaction of hydraulic, mechanical and electric subsystems. Historically, reliability modelling has been split in two directions, focusing on different sub-systems, and has not yet been unified. Here these approaches are unified with a novel expression of unbalanced forces. This model with operational data are validated and the important modes of oscillation in the shaft are identified. Finally, the mechanism of the first-order oscillation mode exciting a second-order mode is presented. This integrated and accurate mathematical model is a major advance in the diagnosis and prediction of failures in hydropower operation.

Mixed transition metal oxides with high theoretical capacity show great potential to replace carbonaceous anode materials in lithium-ion batteries.

Abstract The phase change of sodium acetate (SA) aqueous solution to sodium acetate trihydrate (SAT) requires large supercooling degree, then the aqueous solution can be at liquid state at fairly low temperature without releasing the stored latent heat. Such a feature makes SAT a promising material for seasonal solar thermal energy storage. The present study firstly summarized the thermo-physical properties of the solid SAT and liquid SA aqueous solution at different temperatures and concentrations, including equilibrium temperatures, densities, specific heats and thermal conductivities. The calculation methods of these properties have been established. Secondly, with the aid of the above properties, a mathematic model of the thermal discharge process of the storage system, i.e. the solidification process of supercooled SA aqueous solution, was built based on the heat transfer between the phase changing material within a single storage tube and the external flowing heat transfer fluid (HTF). The experimentally obtained SAT crystal growth rate and the enthalpy change of solidifying supercooled SA aqueous solution were employed to aid the modelling. The discharge temperature and thermal power of the storage system were numerically obtained and analysed. The influence of the ambient temperature, the mass flow rate as well as the heat transfer coefficient of the HTF on the thermal discharge performance were discussed. Finally, the seasonal thermal storage density of SAT was given and compared to that of water and some sorption materials.

AbstractHigh‐performance dye‐sensitized solar cell (DSSC) devices rely on photoanodes that possess excellent light‐harvesting capabilities and high surface areas for sufficient dye adsorption. In this work, morphologically controlled SnO2 microstructures were synthesized and used as an efficient light‐backscattering layer on top of a nanocrystalline TiO2 layer to prepare a double‐layered photoanode. By optimizing the thickness of both the TiO2 bottom layer and the SnO2 top layer, a high power conversion efficiency (PCE) of 7.8 % was achieved, an enhancement of approximately 38 % in the efficiency compared with that of a nanocrystalline TiO2‐only photoanode (5.6 %). We attribute this efficiency improvement to the superior light‐backscattering capability of the SnO2 microstructures.

Abstractπ‐Conjugated polyelectrolytes (CPEs) have been studied as interlayers on top of a separate hole transport layer (HTL) to improve the wetting, interfacial defect passivation, and crystal growth of perovskites. However, very few CPE‐based HTLs have been reported without rational molecular design as ideal HTLs for perovskite solar cells (PeSCs). In this study, the authors synthesize a triphenylamine‐based anionic CPE (TPAFS‐TMA) as an HTL for p‐i‐n‐type PeSCs. TPAFS‐TMA has appropriate frontier molecular orbital (FMO) levels similar to those of the commonly used poly(bis(4‐phenyl)‐2,4,6‐trimethylphenylamine) (PTAA) HTL. The ionic and semiconducting TPAFS‐TMA shows high compatibility, high transmittance, appropriate FMO energy levels for hole extraction and electron blocking, as well as defect passivating properties, which are confirmed using various optical and electrical analyses. Thus, the PeSC with the TPAFS‐TMA HTL exhibits the best power conversion efficiency (PCE) of 20.86%, which is better than that of the PTAA‐based device (PCE of 19.97%). In addition, it exhibits negligible device‐to‐device variations in its photovoltaic performance, contrary to the device with PTAA. Finally, a large‐area PeSC (1 cm2) and mini‐module (3 cm2), showing PCEs of 19.46% and 18.41%, respectively, are successfully fabricated. The newly synthesized TPAFS‐TMA may suggest its great potential as an HTL for large‐area PeSCs.