• Energy Research
• Closed Access close
• Open Source close
• Embargo close
• AU close
• JP close

Abstract A new conical-cylindrical top-discharge blow tank is designed, by introducing the pulsed gas to facilitate discharging, for stable transportation for kaolin powders. A series of experimental studies on pulsed gas characteristic parameters like pulsed gas flow rate Qpulsed (5 m3/h ≤ Qpulsed ≤ 25 m3/h), pulsed interval tpulsed (1 s ≤ tpulsed ≤ 5 s) and pulsed width τpulsed (50 ms ≤ τpulsed ≤ 250 ms) are conducted with the fluidized gas flow rate of 12 m3/h. The experiments mainly test the powder mass flow rate and solid-gas ratio in the conveying process. The results indicate that the mass flow rate and solid-gas ratio range 12.6–278.04 kg/h and 0.9–19.56 kg/m3, respectively. With the increase of the pulsed gas flow rate, the mass flow rate and solid gas ratio first increase and then decrease. When the ratio of fluidized gas flow rate to pulsed gas flow rate is within 0.8–1.2, its conveying capacity reaches the maximum. Meanwhile, the increase in the pulsed interval leads to the decrease of the mass flow rate and solid-gas ratio. Moreover, the increase in the pulsed width leads to the initial increase and then the stabilization of the mass flow rate and solid gas ratio. When the pulsed width is 50 ms, the improvement of discharge would small. Conversely, increasing the pulsed width can increase the discharge, and stabilize subsequently until over 200 ms. Besides, moisture content is one of the important factors affecting kaolin powders discharge. When the moisture content is 0.83%, the pulsed gas does not improve the discharge significantly. Meanwhile, pressure distribution at different locations in the tank is also measured. The results reveal that the introduction of pulsed gas changes the pressure distribution in the tank. A pressure zone is formed on the upper part of the tank, which promotes the powder discharge.

Abstract To achieve optimal generation from a number of mixed power plants by minimizing the operational cost while meeting the electricity demand is a challenging optimization problem. When the system involves uncertain renewable energy, the problem has become harder with its operated generators may suffer a technical problem of ramp-rate violations during the periodic implementation in subsequent days. In this paper, a scenario-based dynamic economic dispatch model is proposed for periodically implementing its resources on successive days with uncertain wind speed and load demand. A set of scenarios is generated based on realistic data to characterize the random nature of load demand and wind forecast errors. In order to solve the uncertain dispatch problems, a self-adaptive differential evolution and real-coded genetic algorithm with a new heuristic are proposed. The heuristic is used to enhance the convergence rate by ensuring feasible load allocations for a given hour under the uncertain behavior of wind speed and load demand. The proposed frameworks are successfully applied to two deterministic and uncertain DED benchmarks, and their simulation results are compared with each other and state-of-the-art algorithms which reveal that the proposed method has merit in terms of solution quality and reliability.

Much of New South Wales and southern Queensland suffered from extreme drought from 2017 to 2019. This study models drought and bushfires impacts using VU‐TERM, a multi‐regional, dynamic CGE model. Prolonged drought pushed national real GDP to 0.7 per cent or more below base in 2018–2019 and 2019–2020. NSW’s real GDP fell relative to forecast by 1.1 per cent or $6.9 billion in 2018–2019 and 1.6 per cent or $10.2 billion in 2019–2020. These impacts reflect a severe diminution of farm output, given that agriculture accounts for around 1.6 per cent of NSW’s income. Bushfires exacerbated 2019–2020 losses. We assume that there is a full recovery in seasonal conditions in 2020. However, prolonged drought and bushfire destruction deplete farm capital through depressed investment and diminished herd numbers. Consequently, the income earning capacity of farms in recovery remains below that of a no drought base. The net present value of the national welfare loss is $63 billion, split between $53 billion in losses from drought and $10 billion from bushfires. The latter excludes any valuation of human lives lost, flora, fauna or forestry destruction. In the longer term, adaptation and policy responses will need to reflect the expectation of increased frequency of adverse climatic events.

Anaphylactic reactions to ethanol are rare with only seven cases reported in the literature. All previous cases have occurred following ingestion of alcoholic beverages or food to which an alcoholic beverage has been added. To date there are no cases in the literature of ethanol-induced anaphylaxis caused by the accumulation of endogenous ethanol in overripe fruit.We report a patient with ethanol-induced anaphylaxis who developed anaphylaxis following ingestion of overripe, but not fresh rock melon (Cucumis melo). The patient is a 24-year-old, previously well woman who experienced five episodes of acute anaphylaxis following ingestion of various alcoholic beverages and, on one occasion, following ingestion of overripe rock melon to which no ethanol was added. Ethanol-induced anaphylaxis was confirmed on blinded challenge; however, challenge with freshly prepared rock melon was negative. The patient declined further challenges.Ingestion of overripe fruits may cause anaphylaxis in patients with ethanol-induced anaphylaxis. These patients should therefore, be advised to avoid ingestion of overripe fruits.

Abstract It is demonstrated that the fuel deposit has a significant influence on the NOx and particular matter (PM) emissions, especially with the consideration of the more and more strict emission regulations issued by the governments, which results in that the near-nozzle spray has been received the increased attention, recently. In this study, the near-nozzle spray characteristics at the initial and end stages were investigated by a high-resolution camera with a laser as the light source. At the initial stage, microscopic behaviors of the near-nozzle spray were observed at upstream, midstream and downstream, respectively. Moreover, the injection frequency was changed to check the effect on the near-nozzle spray morphology. Next, the micro spray length, width and angle were obtained from the processed images. While, at the end stage, the near-nozzle spray evolutions were observed and characterized at 0.5, 0.3, 0.2 and 0.1 ms before the end of injection (BEOI), the end of injection (EOI), 0.05, 0.1, 0.15 and 0.2 ms after the end of injection (AEOI), respectively. Furthermore, the droplet area, spray area without droplets, droplet number and averaged diameter were calculated. Results show that three structures of the near-nozzle spray at the initial stage can be classified as mushroom, steeple and cylinder shapes. And the injection frequency has an influence on their formations owing to the residual fuel and sucked air AEOI. Moreover, although more droplets can be identified at the end stage with time, it does not indicate the better atomization. On the contrary, these droplets AEOI are responsible for the injector deposit in the real engine.

Abstract A three dimensional numerical model of the northwest (NW) Sabalan geothermal system was developed on the basis of the designed conceptual model from available field data. A numerical model of the reservoir was expressed with a grid system of a rectangular prism of 12 km × 8 km with 4.6 km height, giving a total area of 96 km2. The model has 14 horizontal layers ranging in thickness between 100 m to 1000 m extending from a maximum of 3600 to −1000 m a.s.l. Fifteen rock types were used in the model to assign different horizontal permeabilities from 5.0 × 10−18 to 4.0 × 10−13 m2 based on the conceptual model. Natural state modeling of the reservoir was performed, and the results indicated good agreements with measured temperature and pressure in wells. Numerical simulations were conducted for predicting reservoir performances by allocating production and reinjection wells at specified locations. Three different exploitation scenarios were examined for sustainability of reservoir for the next 30 years. Effects of reinjection location and required number of makeup wells to maintain the specified fluid production were evaluated. The results showed that reinjecting at Site B, immediate adjacent to production zone, is most effective for pressure maintenance of the system. On the base of existing data and assumptions the reservoir can sustain producing fluid equivalent to 50 MWe of electricity for more than 30 years. The reservoir can produce the maximum amount of fluids equivalent to 90–100 MWe for only 5 years, but the production capacity decreases to 50 MWe after 20 years of operation because of pressure and enthalpy drop. The reservoir can sustain 50 MWe over 100 years that can be defined as a sustainable production level of the field.

This paper investigates the intact and damage survivability of a floating–moored Oscillating Water Column (OWC) device using physical model experiments and Computational Fluid Dynamics (CFD) simulations. Different extreme wave conditions have been tested using irregular and regular wave conditions. The device was moored to the tank floor via four vertical taut lines and the effect of the mooring line pre–tension on the device response was studied. It was found that the instantaneous position of the floating device was a key factor in the survivability analysis such that a certain irregular wave train that might not include the largest wave could induce the maximum response. Reducing the pre–tension minimized the maximum surge, but significantly increased the maximum tension due to mooring slack events causing snatch loads. A design regular wave with a period equal to the peak period and a height of 1.9–2.0 times the significant wave height could reasonably predict the same maximum line tension as the irregular sea state, but a smaller wave height was required to achieve the maximum surge. A single failure in the mooring system increased the maximum tension by 1.55 times the intact tension. For a damaged mooring system, using the same design regular wave condition derived from the survivability analysis with an intact mooring system could result in overestimating the maximum tension by more than 20% in comparison to the tension from the irregular sea state, but a smaller regular wave height or a different regular wave condition representing another sea state could lead to the same maximum tension. This highlighted the importance of investigating survival conditions with a damaged mooring system instead of simply using the same conditions derived for the intact mooring system.