• Energy Research
• Restricted close
• Embargo close
• AU close
• RU close

Synopsis Climate change can directly and indirectly affect species distribution. Warming may allow for invasive species, such as apple snails, to migrate to higher latitudes where temperatures are more conducive to their survival and invasion success. Higher temperatures and lower pH ranges have been previously documented to affect the form and function of calcium carbonate shells, which serve many functions, including protection from predators and thermoregulation. This study aimed to quantify differences in the morphology and mechanical properties of invasive apple snail, Pomacea maculata, shells after altering temperature and pH. We mechanically tested shells among three five-week treatments: control, higher temperature, and lower pH. Ultimate Strength increased in shells that were exposed to higher temperatures, but Young’s Modulus and Peak Load did not differ among control, temperature, and pH treatments. Apple snails in higher temperature tanks increased their shell length over the five-week trials. Although snail morphometrics did not differ between sexes, male shells exhibited a higher Peak Load, Young’s Modulus, and Ultimate Strength compared to female shells. Our findings are consistent with previous gastropod studies, in that a lower pH is associated with a decrease in shell size, and higher temperatures yield larger snail shells with a higher ultimate strength. Peak Load did not significantly differ among treatments, which suggests that the cross-sectional area is relatively important when considering this species mechanical performance today and in future climates. Due to the intense nutritional and calcium demands of egg production, female snails may be more susceptible to weakened shells due to low pH environments caused by climate change.

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

Ostrava in the Moravian-Silesian region (Czech Republic) is a European air pollution hot spot for airborne particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), and ultrafine particles (UFPs). Air pollution source apportionment is essential for implementation of successful abatement strategies. UFPs or nanoparticles of diameter <100 nm exhibit the highest deposition efficiency in human lungs. To permit apportionment of PM sources at the hot-spot including nanoparticles, Positive Matrix Factorization (PMF) was applied to highly time resolved particle number size distributions (NSD, 14 nm-10 μm) and PM0.09-1.15 chemical composition. Diurnal patterns, meteorological variables, gaseous pollutants, organic markers, and associations between the NSD factors and chemical composition factors were used to identify the pollution sources. The PMF on the NSD reveals two factors in the ultrafine size range: industrial UFPs (28%, number mode diameter - NMD 45 nm), industrial/fresh road traffic nanoparticles (26%, NMD 26 nm); three factors in the accumulation size range: urban background (24%, NMD 93 nm), coal burning (14%, volume mode diameter - VMD 0.5 μm), regional pollution (3%, VMD 0.8 μm) and one factor in the coarse size range: industrial coarse particles/road dust (2%, VMD 5 μm). The PMF analysis of PM0.09-1.15 revealed four factors: SIA/CC/BB (52%), road dust (18%), sinter/steel (16%), iron production (16%). The factors in the ultrafine size range resolved with NSD have a positive correlation with sinter/steel production and iron production factors resolved with chemical composition. Coal combustion factor resolved with NSD has moderate correlation with SIA/CC/BB factor. The organic markers homohopanes correlate with coal combustion and the levoglucosan correlates with urban background. The PMF applications to NSD and chemical composition datasets are complementary. PAHs in PM1 were found to be associated with coal combustion factor.

Abstract Thermal energy storage systems for both heat and cold are necessary for many industrial processes. High energy density and high power capacity are desirable properties of the storage. The use of latent heat increases the energy density of the storage tank with high temperature control close to the melting point. Tube in PCM tank is a very promising system that provides high packing factor. This work presents an experimental study of a PCM tank for cold storage applications. Two different configurations and different flow rates of the heat transfer fluid were studied. The effectiveness of the PCM storage system was defined as that of a heat exchanger. The results showed that the heat exchange effectiveness of the system did not vary with time, decreased with increasing flow rate and increased with increasing heat transfer area. The effectiveness was experimentally determined to only be a function of the ratio m ˙ /A. This equation was found to be adequately be used to design a PCM storage system, and a case study is presented. It was shown that the tube in tank design together with a low temperature PCM is suitable as a thermal storage facility for cold storage.

The paper presents a method of analysis and design of urban landscapes called PlaceMaker. The method is intended as a key resource for assessing the identity of places and measures for its enhancement, reconstruction and design. By using different tools for analysis and interpretation of places and questionnaires administered to their users, PlaceMaker finds the identity material that the city has available and how to de-compose and re-compose it for its sustainable project transformation. Pedestrian-intensive areas, in particular urban, cultural and historical poles of attraction, increasingly bear the imprint of globalization, conveying messages which have developed in an uncontrolled manner and are aimed at conveying their users' patterns of thought and action. The presence of a dense mixture of contrasting elements and perceptions can detract from the image of a city. As regards, the paper is completed with a synopsis of the experiment carried out in an historic axe in London - Oxford Street - where globalization is in danger of levelling out the beauty of the area in favour of widespread genericity

A commercial drum chipper was fed alternately and piecewise with poplar stems and poplar tops, in order to determine the effect of piece size and tree part on machine performance. Chipping stems required most of the available power (231 kW) delivered by the tractor, whereas chipping tops took about half that much. However, productivity was twice as high with stems, compared to tops (i.e. 25 and 11 t h-1 of oven dry wood, respectively). As a consequence, specific fuel consumption per unit product was 15% lower with stems, compared to tops - i.e. 0.61 and 0.72 L m-3, respectively. Mean feeding speed was 0.37 m s-1 for stems and 0.41 m s-1 for tops, but the difference was not significant (p = 0.1677). Productivity and fuel consumption were strongly related to piece size, but tree part had its own additional effect, independent from size and possibly related to form. When chipping tops it is advisable to feed more pieces at a time, in order to partly compensate for the effect of piece size. Operators expecting to chip primarily small-size materials may acquire special chipper versions with wider drums and additional side rollers, for smoother mass feeding. oThe same chipper was tested with poplar stems and tops.oChipping stems resulted in higher productivity and lower fuel consumption.oChipping stems required most of the available tractor power.oChip particle size distribution was about the same for both feedstocks. © 2013 Elsevier Ltd.

In Italy, olive tree groves may offer up to a million tonnes of dry biomass per year as pruning residue. Searching for a cost-effective way to tap this potential, the authors tested a new machine, capable of recovering pruning residue at the same time as pruning. The pre-commercial prototype was tested on four different plots and compared to a simpler tractorbase mechanical pruning unit. The authors conducted detailed time-studies in order to determine machine productivity and residue recovery cost. The integrated machine can treat between 0.2 and 0.6 ha h(-1), producing between 0.33 and 1.03 tonnes of fresh residue hour(-1). Its integrated residue recovery function does not slow the pruning, which actually proceeds faster than with the tractor-base unit, due to the more efficient multiple-disc cutting bar. The marginal cost of residue recovery hovers around 40-45 (sic) fresh tonne(-1). However, the new machine must not be considered just as a biomass harvester, but rather as a mechanical pruning unit with an integrated biomass recovery function. Its main benefit derives from the capacity of performing a very effective mechanical pruning, and the residue recovery function is a secondary benefit yet unavailable on standard pruning machines. Its deployment must be seen in the context of a general effort to modernize olive grove management and to develop an integrated biomass production system, rather than as a further attempt to build a specialised biomass supply chain.

Artículos en revistas Advanced Metering Infrastructures (AMI) represent one of the first steps in the Smart Grid process, where Power Line Communication (PLC) is emerging as the most costeffective solution since it allows reusing electric infrastructures as communication channel. However, the performance of this technology is highly affected by the characteristics of the existing distribution network. This article presents a thorough sensitivity analysis to assess the operating limits of smart metering applications for multiple representative configurations of low voltage (LV) networks based on a PLC simulation framework that integrates DLMS/COSEM and PRIME standards. The number of registered nodes and the time to read all meters have been defined as Key Performance Indicators to assess the communication performance. The conclusions drawn from this study provide useful information for the integration of smart meter applications that take advantage of AMI under different local conditions. info:eu-repo/semantics/publishedVersion