• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• other engineering and technologies close
• DE close
• BE close

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

Abstract Social acceptance of innovative technologies is a key element of an effective transition towards more sustainable energy economies. However, innovative technologies like genetic modification also tend to spark controversy and backlash. So far, efforts to inform the public about any risks and benefits of novel technologies not only have struggled to foster acceptance but also neglect the interdependent foundations of consumer decision-making. Through a controlled experiment with German consumers (N = 322), we examine whether consumer support and rejection of genetic modification in bioenergy crops is influenced by the statements and actions of actors throughout the supply chain. In specific, we show that the decision of energy companies to sell and support GM bioenergy positively impacts consumer decisions to support. To ensure that decision outcomes were specifically impacted by the expressions of corporate actors, we controlled for the content and valence of information by random assignment to one of three treatments in which participants received positive, negative, or balanced (risks and benefits) information. We find that negative messaging diminished support and increased rejection relative to the other treatments. Lastly, the statements and actions of corporate actors also exerted an indirect influence on consumer decisions through their interactions with social trust and labels, e.g. greater support by farmers had a positive influence only for those who are more generally trustworthy. Given these results, we anticipate more attention to the importance of actors such as farmers and energy companies for the social acceptance of novel technologies in the energy sphere.

AbstractChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 100 leading journals. To access a ChemInform Abstract of an article which was published elsewhere, please select a “Full Text” option. The original article is trackable via the “References” option.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

Cogeneration of heat and electricity is an important pillar of energy and climate policy. To plan the production and distribution system of combined heat and power (CHP) systems for residential heating, suitable methods for decision support are needed. For a comprehensive feasibility analysis, the integration of the location and capacity planning of the power plants, the choice of customers, and the network planning of the heating network into one optimization model are necessary. Thus, we develop an optimization model for electricity generation and heat supply. This mixed integer linear program (MILP) is based on graph theory for network flow problems. We apply the network location model for the optimization of district heating systems in the City of Osorno in Chile, which exhibits the “checkerboard layout” typically found in many South American cities. The network location model can support the strategic planning of investments in renewable energy projects because it permits the analysis of changing energy prices, calculation of break-even prices for heat and electricity, and estimation of greenhouse gas emission savings.

Virtually developing of automotive power systems is currently experiencing increasing significance due to elevated vehicular electrification and automation of driving functions. The analysis of system-inherent disturbances requires accurate simulation models for both short-term transients or long-term driving cycles. The electrical behavior of electromechanical actuators such as brake or steering highly depends on the mechanical environmental interaction being dependent many variables. This contribution presents a methodology to extract abstracted models of machine driven actuators on the basis of an electric steering. The dynamics of a complex electromechanical model are investigated using pulse response analysis for differentiated operation points. The obtained model reduction is implemented in a frequency-dependent equivalent circuit.

The thermo-hydro-mechanical behaviour of a water-saturated cement-based heat store for domestic applications has been investigated. Numerical simulations have been employed to locate the critical regions during thermal loading, for which analytical solutions have been derived and validated by numerical simulations. The analytical solutions allow a fast screening of materials and design parameters in relation to the stresses induced by thermomechanical loading. Maximum stresses in the system have been quantified based on the thermomechanical properties of three heat exchanger materials selected by design engineers and of the filling material. Sensitivity analyses indicate that the stress distribution is very sensitive to the thermal expansion coefficients of the involved materials. The results of this study can serve as a guide line for the design of the present and similar heat storage systems. The analytical solution developed is a fast and robust method for the evaluation of stresses around heat exchangers embedded in a solid material and can serve as a tool for design optimisation.

The estimation of leak and break frequencies in piping systems is part of the probabilistic safety assessment of technical plants. In this paper, a statistical method based on the evaluation of German operational experience for piping systems with different diameters is described because an earlier estimation has been updated and extended introducing new methodical aspects and data. A major point is the inclusion of structural reliability models based on fracture mechanics calculation procedures. As an example of application the statistical estimation method for leak and break frequencies of piping systems with a nominal diameter of 50 mm (the volume control system of a German pressurized water reactor) was updated. Moreover, the evaluation of the operational experience was extended to 341 years with respect to cracks, leaks and breaks in the volume control system of German pressurized water reactors (PWR). Using the actual database, new calculations of leak and break frequencies have been performed and the results have been compared with previous values.

Abstract The kinetics of methane hydrate decomposition was studied using a semibatch stirred-tank reactor. The decomposition was accomplished by reducing the pressure on a hydrate slurry in water to a value below the three-phase equilibrium pressure at the reactor temperature. The data were obtained at temperatures from 274 to 283 K and pressures from 0.17 to 6.97 MPa. The stirring rates were high enough to eliminate mass-transfer effects. Analysis of the data indicated that the decomposition rate was proportional to the particle surface area and to the difference in the fugacity of methane at the equilibrium pressure and the decomposition pressure. The proportionality constant showed an Arrhenius temperature dependence. An estimate of the hydrate particle diameters in the experiments permitted the development of an intrinsic model for the kinetics of hydrate decomposition.