• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• Embargo close
• BE close
• UA close

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

A reduced-order, “grey-box” model of an active distribution network, intended for dynamic simulations of the transmission system, is derived. The network hosts inverter-based generators as well as static and motor loads, whose dynamic parameters are affected by uncertainty. This issue is addressed using Monte-Carlo simulations. The parameters of the equivalent are adjusted to match as closely as possible the average of the randomized responses, while their dispersion is accounted for through the weights of the weighted least-square minimization. A procedure is used to remove from the identification the parameters with negligible impact. To avoid over-fitting, the equivalent is tuned for multiple large-disturbance simulations. A recursive procedure is used to select the smallest possible subset of disturbances involved in the least-square minimization. Simulation results with a 75-bus MV test-system are reported. They show that the equivalent is able to reproduce with good accuracy the discontinuous controls of inverter-based generators, such as reactive current injection and tripping.

This paper presents the design of an extended Kalman filter (EKF) as a state-of-charge (SoC) estimator for a lithium–titanate (LTO) battery cell. The design is based on a Thevenin model of the equivalent battery electrical circuit with two parallel resistive-capacitive (RC) elements for the emulation of electrolyte polarization effects. The effectiveness of the proposed SoC estimator is verified through computer simulations on the comprehensive nonlinear battery simulation model featuring battery parameter vs. SoC variations, which is subject to highly dynamic loading regimes.

The concept and a new method for the shielded development of bottom gas hydrates have been proposed, the technological phases and constructive elements of their implementation have been substantiated. The research provides for the realization of the idea suggesting the simultaneous dissociation of the vast areas of a gas hydrate deposit, management of the targeted process of the penetration of methane recovered from gas hydrates into water space and its accumulation under the extensive gas-collecting shield wherefrom it is removed by bottom pipe transportation facilities. To do hydraulic fracturing, a well is drilled into the plane of the junction of the surface of a gas hydrate deposit and the rocks of a roof, the open system of fissures in the rocks of a roof is made through which produced gas is released to a gas-collecting blanket in a water.

Abstract This paper discusses the minimization of the fuel consumption of a gasoline engine through dynamic optimization. The minimization uses a mean value model of the powertrain and vehicle. This model has two state variables: the pressure in the engine intake manifold and the engine speed. The control input is the throttle valve angle. The model is identified on a universal engine dynamometer. Optimal state and control trajectories are calculated using Bock’s direct multiple shooting method, implemented in the software MUSCOD-II. The developed approach is illustrated both in simulation and experimentally for a generic test case where a vehicle accelerates from 1100 rpm to 3700 rpm in 30 s . The optimized trajectories yield minimal fuel consumption. The experiments show that a linear engine speed trajectory yields an extra fuel consumption of 13 % when compared to the optimal trajectory. It is shown that, with a simple model, a significant amount of fuel can be saved without loss of the fun-to-drive.

Theoretical and experimental data on the concentrations of methane in different phase states in the porous structure of coals from the Donets Basin are reported. On the saturation of coal samples with methane, the natural conditions of the occurrence of methane in coal beds were simulated for the equilibrium coal–gas system. The amounts of methane dissolved in a solid matrix and adsorbed on the pore surfaces of coal matter were measured by broad-band NMR spectroscopy. The values obtained did not exceed 20% of the total methane absorbed by the sample in an equilibrium state at a pressure of 10 MPa. Sorbed methane was the predominant phase state only upon the opening of a high-pressure chamber after the emission of methane from filtration channels.

Abstract Many countries committed themselves in the Kyoto protocol to reduce greenhouse gas (GHG) emissions. Some of these targeted emission reductions could result from a switch from coal-fired to gas-fired electricity generation. The focus in this work lies on Western Europe, with the presence of the European Union Emission Trading Scheme (EU ETS). For the switching to occur, several conditions have to be fulfilled. First, an economical incentive must be present, i.e. a sufficiently high European Union Allowance (EUA) price together with a sufficiently low natural gas price. Second, the physical potential for switching must exist, i.e. at a given load, there must remain enough power plants not running to make switching possible. This paper investigates what possibilities exist for switching coal-fired plants for gas-fired plants, dependent on the load level (the latter condition above). A fixed allowance cost and a variable natural gas price are assumed. The method to address GHG emission reduction potentials is first illustrated in a methodological case. Next, the GHG emission reduction potentials are addressed for several Western European countries together with a relative positioning of their electricity generation. GHG emission reduction potentials are also compared with simulation results. GHG emission reduction potentials tend to be significant. The Netherlands have a very widespread switching zone, so GHG emission reduction is practically independent of electricity generation. Other counties, like Germany, Spain and Italy could reduce GHG emissions significantly by switching. With an allowance cost following the switch level of a 50% efficient gas-fired plant and a 40% efficient coal-fired plant in the summer season (like in 2005), the global GHG emission reduction (in the electricity generating sector) for the eight modeled zones could amount to 19%.

The presented article will describe an 'effect-cause' model for the purpose of simulating the energy consumption of DC fed light rail vehicles. The model will assess the advantages of hybrid vehicles in terms of energy consumption, network power and voltage variations, line current and losses; and will help sizing and designing a supercapacitor based energy storage system (ESS) for both on-board, and stationary applications. The proposed modeling needs to allow the ESS sizing according to the objective that needs to be achieved, being braking energy recovery, voltage drop compensation and peak power shaving the most common goals of ESS use in hybrid vehicles. The needed power and energy levels will vary in function of the vehicle features and the driving cycle followed. This all can be determined by the quasi-static simulation tool to ease the design process. Another objective of the modeling tool is to evaluate the behaviour of the vehicle power flow controller, which manages the power from/to the ESS in function of the state of several variables.

No abstract available