• Energy Research
• engineering and technology close
• BE close

The interconversion of the ethanolate, hydrate and amorphous form of TMC114 ((3-[(4-amino-benzenesulfonyl)-isobutyl-amino]-1-benzyl-2-hydroxypropyl)-carbamic acid hexahydrofuro-[2,3-b]furan-3-yl ester) in open conditions was characterized. TMC114 hydrate and ethanolate form isostructural channel solvates. The crystal structure of TMC114 was obtained from single crystal X-ray diffraction, confirming that it is a channel solvate. Ethanol and water can exchange with one another. TMC114 ethanolate converts into TMC114 hydrate at moderate or high relative humidity (RH) at 25 degrees C, and it converts back into the ethanolate in ethanol atmosphere. The hydration level of the hydrate is determined by the environmental humidity. TMC114 hydrate collapses to the amorphous product when water is removed by drying at low RH or increasing temperature. TMC114 ethanolate becomes amorphous at elevated temperature in a dry environment below the desolvation temperature. Amorphous TMC114 obtained by dehydrating the hydrate during storage at room temperature/<5% RH, by increasing the temperature, or via desolvating the ethanolate by heating, converts into the hydrate at moderate or high RH at ambient conditions, and into TMC114 ethanolate in an ethanol atmosphere. Under ambient conditions, TMC114 ethanolate may convert into the hydrate, whereas the opposite will not occur under these conditions. The amorphous form, prepared by melting-quenching shows a limited water uptake. Whereas TMC114 ethanolate is stable in the commercialized drug product, special conditions can trigger its conversion.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

In the current situation with the unprecedented deployment of clean technologies for electricity generation, it is natural to expect that storage will play an important role in electricity networks. This paper provides a qualitative methodology to select the appropriate technology or mix of technologies for different applications. The multiple comparisons according to different characteristics distinguish this paper from others about energy storage systems. Firstly, the different technologies available for energy storage, as discussed in the literature, are described and compared. The characteristics of the technologies are explained, including their current availability. In order to gain a better perspective, availability is cross-compared with maturity level. Moreover, information such as ratings, energy density, durability and costs is provided in table and graphic format for a straightforward comparison. Additionally, the different electric grid applications of energy storage technologies are described and categorised. For each of the categories, we describe the available technologies, both mature and potential. Finally, methods for connecting storage technologies are discussed.

A reduced-order, “grey-box” model of an active distribution network, intended for dynamic simulations of the transmission system, is derived. The network hosts inverter-based generators as well as static and motor loads, whose dynamic parameters are affected by uncertainty. This issue is addressed using Monte-Carlo simulations. The parameters of the equivalent are adjusted to match as closely as possible the average of the randomized responses, while their dispersion is accounted for through the weights of the weighted least-square minimization. A procedure is used to remove from the identification the parameters with negligible impact. To avoid over-fitting, the equivalent is tuned for multiple large-disturbance simulations. A recursive procedure is used to select the smallest possible subset of disturbances involved in the least-square minimization. Simulation results with a 75-bus MV test-system are reported. They show that the equivalent is able to reproduce with good accuracy the discontinuous controls of inverter-based generators, such as reactive current injection and tripping.

In Belgium, and many other countries, rooftop solar panels are becoming a ubiquitous form of decentralised energy production. The increasing share of these distributed installations however imposes many challenges on the operators of the low-voltage distribution grid. They must keep the voltage levels and voltage balance on their grids in check and are often regulatory required to provide sufficient reception capacity for new power producing installations. By placing solar panels in different inclinations and azimuth angles, power production profiles can possibly be shifted to align more with residential power consumption profiles. In this article, it is investigated if the orientation of solar panels can have a mitigating impact on the integration problems on residential low voltage distribution grids. An improved simulation model of a solar panel installation is constructed, which is used to simulate the impact on a residential distribution grid. To stay as close to real-life conditions as possible, real irradiation data and a model of an existing grid are used. Both the developed model as the results on grid impact are evaluated.

This paper focuses on the specific growth rate estimation problem in a Polyhydroxybutyrate bioplastic production process by industrial fermentation. The kinetics of the process are unknown and there are uncertainties in the model parameters and inputs. During the first hours of the growth phase of the process, biomass concentration can be measured online by an optical density sensor, but as cell density increases this method becomes ineffective and biomass measurement is lost. An asymptotic observer is developed to estimate the growth rate for the case without biomass measurement based on corrections made by a pH control loop. Furthermore, an exponential observer based on the biomass measurement is developed to estimate the growth rate during the first hours, which gives the initial condition to the asymptotic observer. Error bounds and robustness to uncertainties in the models and in the inputs are found. The estimation is independent of the kinetic models of the microorganism. The characteristic features of the observer are illustrated by numerical simulations and validated by experimental results.

Abstract This paper discusses the minimization of the fuel consumption of a gasoline engine through dynamic optimization. The minimization uses a mean value model of the powertrain and vehicle. This model has two state variables: the pressure in the engine intake manifold and the engine speed. The control input is the throttle valve angle. The model is identified on a universal engine dynamometer. Optimal state and control trajectories are calculated using Bock’s direct multiple shooting method, implemented in the software MUSCOD-II. The developed approach is illustrated both in simulation and experimentally for a generic test case where a vehicle accelerates from 1100 rpm to 3700 rpm in 30 s . The optimized trajectories yield minimal fuel consumption. The experiments show that a linear engine speed trajectory yields an extra fuel consumption of 13 % when compared to the optimal trajectory. It is shown that, with a simple model, a significant amount of fuel can be saved without loss of the fun-to-drive.