• Energy Research
• 2016-2025close
• Closed Access close
• Embargo close
• BE close

Abstract Various assumptions are often made to model turbomachinery bladed assemblies. In particular, the cyclic symmetry of single rotor stages, and dynamically independence of isolated rotor stages are frequently used. The first assumption enables a drastic reduction of the required computational resources by considering only one sector instead of the entire assembly to model and analyze the dynamic behavior of the complete structure. However, small random blade-to-blade structural variations, known as mistuning, exist due to manufacturing tolerances, etc. and significantly affect the dynamic behavior of bladed disks. The second assumption also reduces the needed computational resources and time. However, ignore inter-stage coupling does not always describe accurately the disk or drum flexibility especially at the inter-stage boundaries. In this work, the component mode mistuning method is used for multi-stage assemblies to create a mistuning identification approach. An experimental modal analysis is performed on a two-stage monobloc academic bladed drum. The frequency response function is measured using a base excitation with an electrodynamic shaker and one measurement point per blade of each stage is used. The approach is used to identify mistuning in a multi-stage rotor. Numerical and experimental results are presented. Results show that the proposed approach is effective even for modes which are multi-stage.

The growing interest for in situ sensing in nanoliter droplets warrants a deeper study of the sensing capabilities and wetting principal of very small electrochemical sensing electrodes in contact with microfluidic droplets. For this study, a device consisting of a droplet generator followed by a 100 μm wide channel with a three-electrode set-up with a 10 μm wide working electrode is used. For measurements 5 mM ferri-/ferrocyanide was used as standard redox couple. It was experimentally found that a thin layer of the droplet phase was left behind on the electrodes, suggesting that the droplets do not need to wet the electrodes but rather merge with the water layer present on the electrodes. With this device, it was possible to detect the redox couple inside the microfluidic droplets and the currents reached a well-defined plateau almost immediately. However, the currents measured inside the droplets deviated from the expected trends for currents measured in flow. Also, a linear concentration curve could be obtained indicating that electrochemical quantitative sensing remains possible.

AbstractVegetation productivity first increases and then decreases with temperature; and temperature corresponding to the maximum productivity is called optimal temperature (Topt). In this study, we used satellite derived near‐infrared reflectance of vegetation (NIRv) data to map Topt of vegetation productivity at the spatial resolution of 0.1° on the Tibetan Plateau (TP), one of most sensitive regions in the climate system. The average Topt of non‐forest vegetation on the TP is about 14.7°C, significantly lower than the Topt value used in current ecosystem models. A remarkable geographical heterogeneity in Topt is observed over the TP. Higher Topt values generally appear in the north‐eastern TP, while the south‐western TP has relatively lower Topt (<10°C), in line with the difference of climate conditions and topography across different regions. Spatially, Topt tends to decrease by 0.41°C per 100 m increase in elevation, faster than the elevational elapse rate of growing season temperature, implying a potential CO2 regulation of Topt in addition to temperature acclimation. Topt increases by 0.66°C for each 1°C of rising mean annual temperature as a result of vegetation acclimation to climate change. However, at least at the decadal scale, there is no significant change in Topt between 2000s and 2010s, suggesting that the Topt climate acclimation may not keep up with the warming rate. Finally, future (2091–2100) warming could be close to and even surpass Topt on the TP under different RCP scenarios without considering potential climate acclimation. Our analyses imply that the temperature tipping point when the impact of future warming shifts from positive to negative on the TP is greatly overestimated by current vegetation models. Future research needs to include varying thermal and CO2 acclimation effects on Topt across different time scales in vegetation models.

Abstract This contribution experimentally evaluates and compares the performance of an ORC (organic Rankine cycle) system for stationary bottoming WHR (waste heat recovery) application operating with two different working fluids, SES36 and R245fa. The test rig is a regenerative cycle equipped with a single screw expander modified from a standard compressor characterized by a nominal shaft power of 11 kW. A total of 36 and 43 steady-state points are collected for SES36 and R245fa respectively, over a wide range of operating conditions by changing the expander rotational speed, the pump frequency and the cooling condenser flow rate. The performances of the ORC components are individually evaluated. A maximum expander isentropic efficiency of 60% is reached using SES36 at 3000 rpm, and a value of 52% is reached with R245fa at 3000 rpm. However, for a given pressure ratio the expander output power is higher with R245fa than with SES36. The overall performance of the ORC unit are investigated in terms of first and second law efficiencies and net output power for the two fluids. The results experimentally demonstrate the correlation between the working fluid critical temperature and the ORC unit working characteristics for low temperature waste heat recovery applications. Open experimental data are provided for both fluids.

Urban residents are exposed to higher levels of heat stress in comparison to the rural population. As this phenomenon could be enhanced by both global greenhouse gas emissions (GHG) and urban expansion, urban planners and policymakers should integrate both in their assessment. One way to consider these two concepts is by using urban climate models at a high resolution. In this study, the influence of urban expansion and GHG emission scenarios is evaluated at 100 m spatial resolution for the city of Brussels (Belgium) in the near (2031-2050) and far (2081-2100) future. Two possible urban planning scenarios (translated into local climate zones, LCZs) in combination with two representative concentration pathways (RCPs 4.5 and 8.5) have been implemented in the urban climate model UrbClim. The projections show that the influence of GHG emissions trumps urban planning measures in each period. In the near future, no large differences are seen between the RCP scenarios; in the far future, both heat stress and risk values are twice as large for RCP 8.5 compared to RCP 4.5. Depending on the GHG scenario and the LCZ type, heat stress is projected to increase by a factor of 10 by 2090 compared to the present-day climate and urban planning conditions. The imprint of vulnerability and exposure is clearly visible in the heat risk assessment, leading to very high levels of heat risk, most notably for the North Western part of the Brussels Capital Region. The results demonstrate the need for mitigation and adaptation plans at different policy levels that strive for lower GHG emissions and the development of sustainable urban areas safeguarding livability in cities.

The European Union is currently in the process of transformation toward a circular economy model in which different areas of activity should be integrated for more efficient management of raw materials and waste. The wastewater sector has a great potential in this regard and therefore is an important element of the transformation process to the circular economy model. The targets of the circular economy policy framework such as resource recovery are tightly connected with the wastewater treatment processes and sewage sludge management. With this in view, the present study aims to review existing indicators on resource recovery that can enable efficient monitoring of the sustainable and circular solutions implemented in the wastewater sector. Within the reviewed indicators, most of them were focused on technological aspects of resource recovery processes such as nutrient removal efficiency, sewage sludge processing methods and environmental aspects as the pollutant share in the sewage sludge or its ashes. Moreover, other wide-scope indicators such as the wastewater service coverage or the production of bio-based fertilizers and hydrochar within the wastewater sector were analyzed. The results were used for the development of recommendations for improving the resources recovery monitoring framework in the wastewater sector and a proposal of a circularity indicator for a wastewater treatment plant highlighting new challenges for further researches and wastewater professionals.

Abstract The numerical simulation of turbulent heat transfer in complex industrial flows represents a major challenge for RANS models. The impinging jet configuration is a popular test case for turbulence models, due to both the challenging nature of the flow field for the RANS approach and its widespread use in industrial applications. As a consequence, a large number of studies in the literature is dedicated to the assessment of a broad variety of turbulence models in this configuration. In particular, a significant effort has been put into the assessment of different closures for the turbulent momentum flux. In contrast, relatively little attention has been paid to the modelling of the turbulent heat flux term, and the classical Reynolds analogy is almost universally employed for this purpose despite its well-known limitations. Nevertheless, recently there has been a growing interest towards the development and assessment of more advanced closures for the turbulent heat flux. In this context, in the present work six turbulence models relying on different closures for both the turbulent momentum and heat fluxes have been used to simulate a planar impinging jet at unity, moderate and low Prandtl number and thoroughly assessed against a recently published reference DNS database. It is shown that the use of an advanced differential closure for the Reynolds stresses can result in an improvement in the prediction of the flow field. This, in turn, directly results in a more accurate prediction of the mean temperature at unity Prandtl number when the Reynolds analogy is employed for the closure of the turbulent heat flux. On the other hand, the inadequacy of the latter approach appears evident at low Prandtl values, and the necessity to account at least for the variability of the turbulent Prandtl number is demonstrated. It is then inferred that the most promising approach for such complex cases is represented by the combined use of anisotropic models for both the turbulent flow and the thermal fields.

Abstract A linear economy approach results in many environmental challenges: resources become depleted and end up as waste and emissions. One of the key strategies to overcome these problems is using waste as a resource, i.e. evolving toward a circular economy. To monitor this transition, suitable indicators are needed that focus on sustainability issues whilst taking into account the technical reality. In this paper, we develop such an indicator to quantify the circular economy performance of different plastic waste treatment options. This indicator is based on the technical quality of the plastic waste stream and evaluates resource consumption by using the Cumulative Exergy Extraction from the Natural Environment (CEENE) method. To illustrate the use of this new indicator, it was applied in a case study on post-industrial plastic waste treatment. The results show that the indicator can be a very useful approach to guide waste streams towards their optimal valorization option, based on quality of the waste flow and the environmental benefit of the different options.