• Energy Research
• Closed Access close
• Open Source close
• US close
• CA close
• AU close

Abstract We demonstrate the importance of stock turnover on industrial energy efficiency through a literature review and a case study of energy-intensive equipment, i.e. the electric arc furnace in the US steel industry. We describe the common methods for assessing stock turnover. We have found that both stock turnover and retrofit are important elements to explain the energy efficiency improvement rates. We investigated the development of electricity use in electric arc furnaces in the United States by tracking the development of individual furnaces over the period 1990–2002. This provides a detailed picture of changes in the stock or fleet of furnaces through turnover and/or retrofit. Our results confirm the results of other empirical studies that there is no clear lifetime of equipment. However, retired furnaces are distinctly less efficient than furnaces remaining in the stock, while new furnaces are distinctly more efficient than the average stock. We found an annual average improvement in specific electricity consumption of 1.3%/year over the studied period, of which 0.7%/year was due to stock turnover and 0.5%/year due to retrofit of stock in service throughout the period.

Structural and physiological changes that occur as trees grow taller are associated with increased hydraulic constraints on leaf gas exchange, yet it is unclear if leaf-level constraints influence whole-tree growth as trees approach their maximum size. We examined variation in leaf physiology, leaf area to sapwood area ratio (L/S), and annual aboveground growth across a range of tree heights in Eucalyptus regnans. Leaf photosynthetic capacity did not differ among upper crown leaves of individuals 61.1-92.4 m tall. Maximum daily and integrated diurnal stomatal conductance (g s) averaged 36 and 34% higher, respectively, in upper crown leaves of ~60-m-tall, 80-year-old trees than in ~90-m-tall, 300-year-old trees, with larger differences observed on days with a high vapor pressure deficit (VPD). Greater stomatal regulation in taller trees resulted in similar minimum daily leaf water potentials (Ψ L) in shorter and taller trees over a broad range of VPDs. The long-term stomatal limitation on photosynthesis, as inferred from leaf δ (13)C composition, was also greater in taller trees. The δ (13)C of wood indicated that the bulk of photosynthesis used to fuel wood production in the main trunk and branches occurred in the upper crown. L/S increased with tree height, especially after accounting for size-independent variation in crown structure across 27 trees up to 99.8 m tall. Despite greater stomatal limitation of leaf photosynthesis in taller trees, total L explained 95% of the variation in annual aboveground biomass growth among 15 trees measured for annual biomass growth increment in 2006. Our results support a theoretical model proposing that, in the face of increasing hydraulic constraints with height, whole-tree growth is maximized by a resource trade-off that increases L to maximize light capture rather than by reducing L/S to sustain g s.

Abstract Many energy-related investments are made without a clear financial understanding of their values, risks, and volatilities. In the face of this uncertainty, the investor—such as a building owner or an energy service company—will often choose to implement only the most certain and thus limited energy-efficiency measures. Conversely, commodities traders and other sophisticated investors accustomed to evaluating investments on a value, risk, and volatility basis often overlook energy-efficiency investments because risk and volatility information are not provided. Fortunately, energy-efficiency investments easily lend themselves to such analysis using tools similar to those applied to supply side risk management. Accurate and robust analysis demands a high level of understanding of the physical aspects of energy-efficiency, which enables the translation of physical performance data into the language of investment. With a risk management analysis framework in place, the two groups—energy-efficiency experts and investment decision-makers—can exchange the information they need to expand investment in demand-side energy projects. In this article, we first present the case for financial risk analysis in energy efficiency in the buildings sector. We then describe techniques and examples of how to identify, quantify, and manage risk. Finally, we describe emerging market-based opportunities in risk management for energy efficiency.

This paper gives a introduction of a SMES unit using 2G HTS wires. A complete SMES system including both superconducting coils and control circuit has been designed to operate at 77 K. Three single-phase H-bridge converters have been used in the control circuit. A loop control signal is sent out by using 32 fixed point Digital Signal Processor (DSP). The complete circuit has been both modelled in simulation and built experimentally. The results validate that this SMES successfully compensates a voltage sag in a power system.

The catalytic active sites of NiFe and NiFeCr (oxy)hydroxides are revealed byoperandospectroscopic techonologies for alkaline water oxidation.

Abstract The influence of the solid-phase wall boundary condition was investigated in Eulerian–Eulerian numerical simulations of a bubbling fluidized bed. Parametric studies of the particle–wall restitution coefficient and specularity coefficient were performed to evaluate their impact on the predicted flow hydrodynamics in terms of bed expansion, local voidage, and solid velocity. Both two- and three-dimensional simulations were conducted and compared with available experimental data on solid velocity and bubble properties. It is found that the wall effect plays an important role in CFD models. Such factors as the voidage at the bubble boundary, averaging method, and minimum bubble size also influence the mean bubble diameter.

This paper develops a strategy for the continuing and improved supply of woodfuels to urban and industrial consumers in Sub-Sahara Africa. It argues that continued use of these fuels is not only a necessity, but is also in the best economic interest of most of the countries in this region. It shows that intensified and more orderly utilization of woodfuels can help to enhance, rather than impinge upon environmental parameters. Some examples are provided that illustrate how such strategies can be put into practice.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

Abstract Moltres is a new physics application for modeling coupled physics in fluid-fuelled, molten salt reactors. This paper describes its neutronics model, thermal hydraulics model, and their coupling in the MOOSE framework. Neutron and precursor equations are implemented using an action system that allows use of an arbitrary number of groups with no change in the input card. Results for many-channel configurations in 2D-axisymmetric and 3D coordinates are presented and compared against other coupled models as well as the Molten Salt Reactor Experiment.