• Energy Research
• other engineering and technologies close
• 13. Climate action close
• CA close
• BE close
• MA close
• UA close

Abstract This study develops a novel sustainability assessment methodology for energy systems using life-cycle emission factors and sustainability indicators. Here, the global warming and environmental impact dimensions of the sustainability assessment methodology are examined in detail. A comparative analysis shows that a wind-battery system produces fewer potential global warming, stratospheric ozone depletion, air pollution, and water pollution impacts compared to a gas-fired system. The wind-battery system generates 13% of the life-cycle GHG emissions and 22% of the life-cycle ozone-depleting substance emissions of a gas-fired power plant. Nitrous oxide contributes more than 90% of the stratospheric ozone depletion potential of gas-fired and wind-battery systems.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

The poultry industry is one of the largest and fastest growing sectors of livestock production in the world. The estimated 2010 world flock was over 18 billion birds with a yearly manure output of 22 million tonnes. Storage and disposal of raw poultry manure has become an environmental problem because of the associated air, water and soil pollution. Environmental and health problems such as odor and pathogens that may arise during and after land application of raw manure can be eliminated by drying. Dried manure can be utilized as a soil conditioner to improve soil tilth and reduce the problems associated with soil compaction and as a feed for ruminants because of its high nitrogen content. The aim of this study was to investigate the kinetics of thin layer drying of poultry manure and evaluate the effects of drying with heated air on the chemical and biological properties of manure. The effects of temperature and depth of manure layer were evaluated. The profile of the moisture content of poultry manure followed an exponential decay curve. The moisture decay constant was affected by the drying temperature and the depth of the manure layer. At the three temperature levels studied, the time required to dry poultry manure in 1 cm-deep layer was the least, followed by 2 and 3 cm-deep layers, respectively. The diffusion coefficient increased with both temperature and depth of drying layer, but did not show a linear increase with either variable. The optimum depth for drying manure (at which the highest drying effectiveness occurred) was 3 cm. Drying manure at 40-60°C resulted in the loss of 44-55% of the total Kjeldahl nitrogen, with losses increasing with both the temperature and depth of manure. The pH of the manure decreased from the initial value of 8.4 before drying to about 6.6 after drying. The odor analysis indicated that dried poultry manure did not have an offensive odor. Drying achieved 65.3 and 69.3% reductions in odor intensity and offensiveness, respectively. Reductions in the number of bacteria, mold/yeast and E.coli were 65-99, 74-99 and 99.97% respectively. The greatest reductions in microbial population occurred at the highest temperatures (60°C) and the thinest manure depths (1 cm). Heated air drying of poultry manure at temperatures between 40 and 60°C was effective in killing pathogens and removing odor.

Abstract In this paper, energy and exergy analyses of the geothermal-based hydrogen production via thermochemical water decomposition using a new, four-step copper–chlorine (Cu–Cl) cycle are conducted, and the respective cycle energy and exergy efficiencies are examined. Also, a parametric study is performed to investigate how each step of the cycle and its overall cycle performance are affected by reference environment temperatures, reaction temperatures, as well as energy efficiency of the geothermal power plant itself. As a result, overall energy and exergy efficiencies of the cycle are found to be 21.67% and 19.35%, respectively, for a reference case.

Abstract Hydrogen fuel cells are received increasingly wide attention in order to develop green ships and reduce greenhouse gas emissions in the field of waterway transportation. Metal hydrides (MHs) can be used to store hydrogen for green ships due to their high volumetric storage capacity and safety. Various measures should be considered in the design and manufacture process of the MH reactor to strengthen its performance of heat and mass transfer and obtain an acceptable hydrogen storage capacity. In this work, LaNi5 hydride is used as the hydrogen storage material and packed in the reactor. A basic axisymmetric numerical model for the hydrogen storage system without a heat exchanger has been developed and proved to be effective through the comparison between its simulation results and the published data during dehydriding. A hybrid heat exchanger, which is consisted of a phase change material (PCM) jacket and a coiled-tube, has been applied into the hydrogen storage system to relieve the thermal effect of MH in the dehydriding process on system performance. Effects of the heat transfer coefficient between the circulating heating water in the coil-tube and the MH bed, the temperature of circulating heating water and the pressure at the outlet on the dehydriding performance have been investigated. Based on parametric study, the relationships among the average dehydriding rate, the heat transfer coefficient, the heating water temperature and the outlet pressure have been found and fitted as simple equations. These fitted equations can be considered as a reference, which provides an important method to effectively control the dehydriding rate in order to satisfy the fuel requirement of the power unit and ensure the safe navigation of green ships in the future.

Abstract Geological sequestration of CO 2 is an immediately available and technologically feasible means of reducing CO 2 emissions into the atmosphere, which is particularly suited to landlocked sedimentary basins. Geoscience, engineering, economic and public issues need addressing by governments and industry before proceeding with full scale implementation. Specific site selection should be based on a suitability analysis, a proper inventory of potential sites, an assessment of the fate of the injected CO 2 and a capacity determination, together with surface criteria such as CO 2 capture and transport. The suitability analysis, both at the basin and regional scales, is based on geological, geothermal, hydrodynamic, basin maturity, economic and societal criteria. The inventory of sequestration sites needs also identification of major CO 2 point sources and a cost benefit analysis. The potential for CO 2 escape and migration is a deciding factor in screening out unsafe sites. Site capacity should be determined based on in situ conditions and CO 2 properties and behavior. Transforming the geological space into the CO 2 space is an important step along the road map for selection of suitable CO 2 injection sites that allows the identification of safe large capacity sites. An example of application from the Alberta basin is presented.

Carbon capture, utilization, and storage (CCUS) is a gas injection technology that enables the storage of CO2 underground. The aims are twofold, on one hand to reduce the emissions of CO2 into the atmosphere and on the other hand to increase oil/gas/heat recovery. Different types of CCUS technologies and related engineering projects have a long history of research and operation in the USA. However, in China they have a short development period ca. 10 years. Unlike CO2 capture and CO2-EOR technologies that are already operating on a commercial scale in China, research into other CCUS technologies is still in its infancy or at the pilot-scale. This paper first reviews the status and development of the different types of CCUS technologies and related engineering projects worldwide. Then it focuses on their developments in China in the last decade. The main research projects, international cooperation, and pilot-scale engineering projects in China are summarized and compared. Finally, the paper examines the challenges and prospects to be experienced through the industrialization of CCUS engineering projects in China. It can be concluded that the CCUS technologies have still large potential in China. It can only be unlocked by overcoming the technical and social challenges.

The concept and a new method for the shielded development of bottom gas hydrates have been proposed, the technological phases and constructive elements of their implementation have been substantiated. The research provides for the realization of the idea suggesting the simultaneous dissociation of the vast areas of a gas hydrate deposit, management of the targeted process of the penetration of methane recovered from gas hydrates into water space and its accumulation under the extensive gas-collecting shield wherefrom it is removed by bottom pipe transportation facilities. To do hydraulic fracturing, a well is drilled into the plane of the junction of the surface of a gas hydrate deposit and the rocks of a roof, the open system of fissures in the rocks of a roof is made through which produced gas is released to a gas-collecting blanket in a water.

Abstract In order to further reduce the impact of climate fluctuations on the typical meteorological year (TMY) database, this paper introduces an ensemble empirical model decomposition method to extract the periodic fluctuation and random fluctuation data from outdoor climate data separately, and to construct a comprehensive description parameter that eliminates the influence of random fluctuation data. An innovative TMY based on the comprehensive description parameter was developed in six selected cities of different climate zones in China. Compared with the existing Chinese TMY development method and outdoor design parameters, it is found that the typical meteorological months (TMMs) of each city and the outdoor design parameters from the improved TMY database have changed to a certain extent. Through the correlation analysis between improved TMY database and the cumulative long-average meteorological data, it reveals that the improved TMY can better describe the local average climatic characteristics. Finally, this paper discusses the impact of the improved TMY on the building heat loss index and outdoor thermal comfort in different building shapes. The results demonstrate that the energy demand and outdoor thermal comfort analysis based on the improved TMY are closer to long-term averaged outdoor climate, and the calculation deviations compared with conventional method are reduced by 1.18%–21.08% and 53.42%–76.82% respectively. This research will refine outdoor climate data for building design and analysis.