• Energy Research
• other engineering and technologies close
• 7. Clean energy close
• 11. Sustainability close
• CA close
• BE close
• UA close

This paper examines and optimizes parameters that affect the air cooling of a Lithium-Ion (Li-Ion) battery, used in Electric Vehicles (EVs). A battery pack containing 150 cylindrical type Li-Ion battery cells in a PVC casing is investigated. An equal number of tubes are used in the pack as a medium to cool the battery by using a fan when the vehicle is stationary or with ambient air when in motion. The parameters affecting the air cooling of battery are studied and optimized by considering their practical constraints. The objective function and Number of Transfer Unit (NTU) are developed. Finally, a genetic algorithm method is employed to optimize the decision variables. Analysing the results shows that NTU can be maximized by increasing the diameter of tubes on the battery and keeping the air velocity in a certain range.

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.

Abstract This study develops a novel sustainability assessment methodology for energy systems using life-cycle emission factors and sustainability indicators. Here, the global warming and environmental impact dimensions of the sustainability assessment methodology are examined in detail. A comparative analysis shows that a wind-battery system produces fewer potential global warming, stratospheric ozone depletion, air pollution, and water pollution impacts compared to a gas-fired system. The wind-battery system generates 13% of the life-cycle GHG emissions and 22% of the life-cycle ozone-depleting substance emissions of a gas-fired power plant. Nitrous oxide contributes more than 90% of the stratospheric ozone depletion potential of gas-fired and wind-battery systems.

Abstract In the present study, Loblolly pine biomass residue was converted to bio-oil in a two-step process, consisting of 1) fast pyrolysis in the presence of zeolite ZSM-5 as a catalyst to produce pyrolysis oil, 2) hydrogenation of pyrolysis oil using formic acid as the hydrogen source in presence of Ru/activated carbon catalyst. Pyrolysis oils were analyzed by 13C, 31P and HSQC-NMR and the results revealed that the zeolite-induced catalytic fast pyrolysis process led to effective demethoxylation, producing more catechol and p-hydroxy-phenyl hydroxyl groups in the bio-oils, resulting in a decrease in the methoxyl group content by about 85 % and rich aromatic structures in the pyrolysis oils. The properties of pyrolysis oil with and without zeolite were in the bio-oil range. Hydrogenated pyrolysis oil showed that 79 % of the aromatic protons are eliminated and 87 % of protons are aliphatic in nature, with no oxygen attached to the α-carbon.

Abstract Space–time kinetics calculations for CANDU ® 1 reactors are routinely performed using the Improved Quasistatic (IQS) method. The IQS method calculates kinetics parameters such as the effective delayed-neutron fraction and generation time using adjoint weighting. In the current implementation of IQS, the direct flux, as well as the adjoint, is calculated using a two-group cell-homogenized reactor model which is inadequate for capturing the effect of the softer energy spectrum of the delayed neutrons. Additionally, there may also be fine spatial effects that are lost because the intra-cell adjoint shape is ignored. The purpose of this work is to compare the kinetics parameters calculated using the two-group cell-homogenized model with those calculated using lattice-level fine-group heterogeneous adjoint weighting and to assess whether the differences are large enough to justify further work on incorporating lattice-level adjoint weighting into the IQS method. A second goal is to evaluate whether the use of a fine-group cell-homogenized lattice-level adjoint, such as is the current practice for Light Water Reactors (LWRs), is sufficient to capture the lattice effects in question. It is found that, for CANDU lattices, the generation time is almost unaffected by the type of adjoint used to calculate it, but that the effective delayed-neutron fraction is affected by the type of adjoint used. The effective delayed-neutron fraction calculated using the two-group cell-homogenized adjoint is 5.2% higher than the “best” effective delayed-neutron fraction value obtained using the detailed lattice-level fine-group heterogeneous adjoint. The effective delayed-neutron fraction calculated using the fine-group cell-homogenized adjoint is only 1.7% higher than the “best” effective delayed-neutron fraction value but is still not equal to it. This situation is different from that encountered in LWRs where weighting by a fine-group cell-homogenized adjoint is sufficient to calculate the correct effective delayed-neutron fraction. It is concluded that lattice-level weighting with a detailed fine-group heterogeneous adjoint is desirable for the correct calculation of the effective delayed-neutron fraction in CANDU lattices.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

AbstractChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 100 leading journals. To access a ChemInform Abstract of an article which was published elsewhere, please select a “Full Text” option. The original article is trackable via the “References” option.

In the current situation with the unprecedented deployment of clean technologies for electricity generation, it is natural to expect that storage will play an important role in electricity networks. This paper provides a qualitative methodology to select the appropriate technology or mix of technologies for different applications. The multiple comparisons according to different characteristics distinguish this paper from others about energy storage systems. Firstly, the different technologies available for energy storage, as discussed in the literature, are described and compared. The characteristics of the technologies are explained, including their current availability. In order to gain a better perspective, availability is cross-compared with maturity level. Moreover, information such as ratings, energy density, durability and costs is provided in table and graphic format for a straightforward comparison. Additionally, the different electric grid applications of energy storage technologies are described and categorised. For each of the categories, we describe the available technologies, both mature and potential. Finally, methods for connecting storage technologies are discussed.