• Energy Research
• Open Source close
• Embargo close
• 13. Climate action close
• 11. Sustainability close
• DE close
• CA close

Engineered cementitious composites (ECCs) are special types of fibre-reinforced cementitious composites (FRCC) with higher strain capacity which can be achieved with low fibre volume as low as 2% and total elimination of coarse aggregates. Due to the outstanding performance of ECCs, they are suitable for various construction and repair applications. However, in order for ECCs to achieve their properties; a high amount of binder which is primarily composed of Portland cement (PC) is used alongside a special type of ultrafine silica sand (USS) which is different from the conventional natural fine aggregates. The production of PC is known to be detrimental to the environment due to its high carbon dioxide emissions coupled with the high consumption of natural resources. Thus, the high use of PC content in ECCs posed a sustainability threat. Similarly, the USS used in ECCs are not readily available everywhere and are expensive. The processing of the USS coupled with its transportation over long distances would also increase the cost and embodied carbon of ECCs. Hence, in order to promote more development and applications of ECCs for various applications; this dissertation aims to provide innovative ways to improve the sustainability of ECCs and their performances. This dissertation offers four solutions to improve the sustainability of ECCs which are (i) use of unconventional industrial by-products as partial replacement of PC (ii) total replacement of PC in ECCs with alternative sustainable binders (iii) replacement of USS in ECCs with recycled materials and (iv) the use of supplementary cementitious materials to replace a high volume of PC. The findings from this study revealed sustainable ECCs with acceptable mechanical and durability performance can be achieved with the use of alternative binders or replacement of the conventional USS used in ECC mixtures. The sustainability and cost assessment of the ECCs indicated that the incorporation of industrial by-products such as blast furnace slag (BFS) especially at higher content is beneficial to reducing the negative environmental impact and economic burden associated with ECCs compared to the conventional ECC. The sustainability index and cost index of the ECCs further showed that the use of BFS is more beneficial when the sustainability and cost of the ECCs are compared with the corresponding performance. Similarly, the use of recycled materials as an alternative to USS was found to result in a significant reduction in the embodied carbon and cost of ECCs. The use of recycled materials such as expanded glass (EG) as aggregates in ECCs was also found to improve the thermal insulation properties of ECCs making such ECC suitable for the production of building envelope elements.

In industrialized countries, large amounts of mineral wastes are produced. They are re-used in various ways, particularly in road and earth constructions, substituting primary resources such as gravel. However, they may also contain pollutants, such as heavy metals, which may be leached to the groundwater. The toxic impacts of these emissions are so far often neglected within Life Cycle Assessments (LCA) of products or waste treatment services and thus, potentially large environmental impacts are currently missed. This study aims at closing this gap by assessing the ecotoxic impacts of heavy metal leaching from industrial mineral wastes in road and earth constructions. The flows of metals such as Sb, As, Pb, Cd, Cr, Cu, Mo, Ni, V and Zn originating from three typical constructions to the environment are quantified, their fate in the environment is assessed and potential ecotoxic effects evaluated. For our reference country, Germany, the industrial wastes that are applied as Granular Secondary Construction Material (GSCM) carry more than 45,000 t of diverse heavy metals per year. Depending on the material quality and construction type applied, up to 150 t of heavy metals may leach to the environment within the first 100 years after construction. Heavy metal retardation in subsoil can potentially reduce the fate to groundwater by up to 100%. One major challenge of integrating leaching from constructions into macro-scale LCA frameworks is the high variability in micro-scale technical and geographical factors, such as material qualities, construction types and soil types. In our work, we consider a broad range of parameter values in the modeling of leaching and fate. This allows distinguishing between the impacts of various road constructions, as well as sites with different soil properties. The findings of this study promote the quantitative consideration of environmental impacts of long-term leaching in Life Cycle Assessment, complementing site-specific risk assessment, for the design of waste management strategies, particularly in the construction sector.

Abstract As main contributors to greenhouse gas emissions, power and transportation are crucial sectors for energy system decarbonization. Their interaction is expected to increase significantly: plug-in electric vehicles add a new electric load, increasing grid demand and potentially requiring substantial grid upgrade; hydrogen production for fuel cell electric vehicles or for clean fuels synthesis could exploit the projected massive power overgeneration by intermittent and seasonally-dependent renewable sources via Power-to-Hydrogen. This work investigates the infrastructural needs involved with a broad diffusion of clean mobility, adopting a sector integration perspective at the national scale. The analysis combines a multi-node energy system balance simulation and a techno-economic assessment of the infrastructure to deliver energy vectors for mobility. The article explores the long-term case of Italy, considering a massive increase of renewable power generation capacity and investigating different mobility scenarios, where low-emission vehicles account for 50% of the stock. First, the model solves the energy balances, integrating the consumption related to mobility energy vectors and taking into account power grid constraints. Then, an optimal infrastructure is identified, composed of both a hydrogen delivery network and a widespread installation of charging points. Results show that the infrastructural requirements bring about investment costs in the range of 43–63 G€. Lower specific costs are associated with the exclusive presence of FCEVs, whereas the full reliance on BEVs leads to the most significant costs. Scenarios that combine FCEVs and BEVs lie in between, suggesting that the overall power + mobility system benefits from the presence of both drivetrain options.

Abstract While it is generally accepted that our fossil fuel-dominated energy systems must undergo a sustainable transition, researchers have often neglected the potential impacts of this on water and land systems. However, if unintended environmental impacts from this process are to be avoided, understanding its implications for land use and water demand is of crucial importance. Moreover, developed countries may induce environmental stress beyond their own borders, for instance through extensive imports of bioenergy. In this paper, Germany serves as an example of a developed country with ambitious energy transformation targets. Results show that in particular, the politically-driven aspiration for more organic farming in Germany results in a higher import quota of biomass, especially biofuels. These imports translate into land demand, which will exceed the area available in Germany for bioenergy by a factor of 3–6.5 by 2050. As this will likely bring about land stress in the respective exporting countries, this effect of the German energy transformation ought to be limited as much as possible. In contrast, domestic water demand for the German energy system is expected to decrease by over 80% through 2050 due to declining numbers of fossil-fuelled power plants. However, possible future irrigation needs for bioenergy may reduce or even counterbalance this decreasing effect. In addition, energy policy targets specific to the transport sector show a high sensitivity to biomass imports. In particular, the sector-specific target for greenhouse gas reductions will seemingly promote biomass imports, leading to the above-described challenges in the pursuit of sustainability.

Abstract The rapid uptake of renewable energy sources requires new forms of flexibility in electricity systems, including a more responsive demand-side. The social acceptability, scale and economic value of flexible demand remain subjects of conjecture. In this paper we inform this debate with a multi-methods approach using three instruments: surveys, observations and modelling. This multi-method approach brings out similarities and differences between Germany and Great Britain in relation to demand-side flexibility. Participants in both countries express a high willingness to participate in time variant tariffs, but their implementation may need to be context specific. In Germany national peak demand occurs at midday, when PV generation results in lower emission factors. Conversely, British peak demand is in the early evening when emission factors are at their highest. The differences in responses allow us to explore important technical and cultural differences affecting the need for flexibility. Germany gains most from flexibility during the daytime in summer, while flexibility in Great Britain contributes most during winter evenings. We observe high degrees of acceptability of time-variant electricity tariffs (55%) and willingness to shift demand is high, resulting in peak demand reductions of up to 14.5%. However, the resulting cost and carbon savings of these efforts is less than 2% in both countries. We conclude that short term carbon or cost savings may be less powerful motivators for load shifting measures than long term system decarbonisation.

Abstract Behavior change towards sustainable lifestyles such as adoption of renewable energy technologies is a significant element in the fight against anthropogenic climate change. Increasingly, private households can be observed to take up different renewable energy technologies; however, the introduction of these technologies is not accompanied by a broader adoption of pro-environmental behaviors, as recent studies have shown. At the same time, group settings and social capital seem to promote the uptake of wide-ranging sustainability measures. Six case studies were conducted among different sustainable community projects in Germany to shed light on why and how broad sustainability transformation in such settings comes about. Findings suggest that successful implementation of wide-ranging sustainable measures and changes in behaviors in community settings result from motivations that originate from an interplay of social needs, social capital, social norms, and environmental concern. Strong environmental attitudes, not among all, but a critical mass of members and key individuals are necessary. The desire for community and other motives, along with social influence and social norms push individuals with low environmental concern to participate in sustainable endeavors.

As Europe is not on track in meeting its 2020 energy savings target, there has been quite some debate to make the energy savings target binding instead of indicative. Although the final draft text of the Energy Efficiency Directive left the option of a binding target explicitly open for the period beyond 2014, this statement has watered down in the adopted Directive: If still not on track mid-2014, the European Commission will propose "further measures." In this paper, we argue that a binding energy savings target could be the first EU legal initiative to look beyond 2020 serving as a beacon for other policies such as for renewables and greenhouse gases that need redefinition after 2020. We therefore explore four possible design options of a binding savings target and assess their feasibility. We conclude that a binding target at Member State level (opposed to an EU-wide target like for the EU Emission Trading System (ETS)) is the most feasible. A binding target at Member State level would ensure political accountability and commitment to deliver results while providing flexibility to choose and apply the most suitable tools to achieve the target. It could provide a framework to guide ambitious and coherent implementation of EU energy efficiency policies, as well as the strengthening of national policies. Furthermore, binding targets at Member State level will make Member States take an ambitious position in Brussels when new energy or CO2 performance standards for appliances and transport modes are to be set. A Member State binding target applied to end-users (excluding ETS companies) is a design option that covers the vast majority of the cost-effective energy savings potential, maintains the flexibility for ETS companies, and supports the most cost-effective achievement of a greater share of renewables.

Abstract The transport sector is one of the major drivers of global climate change, with a large share related to the personal use of cars. Paradoxically, as efforts are undertaken to reduce this share, a trend to buy large, heavy cars with comparatively high fuel consumption is occurring nearly worldwide. In this article, we analyze the possible influence of social norms in car-buying decisions and in particular in the trend towards sport utility vehicles (SUVs). We develop a model applying a multi-criteria decision analysis approach and quantify the influence of social norms on car-buying decisions. Four main data sources are used: Surveys on German car buyers and their preferences conducted by VuMA Touchpoints and ARAL, longitudinal data by the Sinus-Institute on different social groups in German society, as well as ADAC assessments on characteristics of different car types. Our results indicate that social norms play a significant role in driving the demand for heavyweight passenger cars across most social groups, while the desire for social esteem leads some groups in particular to purchase SUVs and off-road vehicles. By taking society’s heterogeneity into account, we show that social norms are group-specific and not universal in society. Nevertheless, car choice is to a certain extent always influenced by social norms and ranges among different social groups between 24% and 42% in our model calculations. The novel approach taken in this research can be applied beyond the mobility sector to other environmentally significant consumer behaviors.