• Energy Research
• Open Access close
• Restricted close
• Open Source close
• engineering and technology close
• FR close
• CA close

Editorial Complex Optimization and Simulation in Power Systems

Production of biodiesel from yellow grease (waste cooking oil and waste animal fats) is fast emerging as a promising alternative to address the twin challenges before the biodiesel industry today-fluctuation in prices of vegetable oil and the food versus fuel debate. Yellow grease has a high percentage of free fatty acids (FFA) and proves to be an unsuitable feedstock for biodiesel production from commercially viable alkali-catalyzed production systems due to saponification problems.“Green” methodologies based on heterogeneous solid acid catalyzed reactions have the potential to simultaneously promote esterification and transesterification reactions of yellow grease to produce biodiesel without soap formation and offer easy catalyst separation without generation of toxic streams. This paper presents kinetic studies for the conversion of model yellow grease feeds to biodiesel using a heteropolyacid supported on alumina (HSiW/Al2O3) using a batch autoclave. Three model yellow grease feeds were prepared using canola oil with added FFA such as palmitic, oleic and linoleic acid. A pseudo homogeneous kinetic model for the parallel esterification and transesterification was developed. The rate constants and activation parameters for esterification and transesterification reactions for the model yellow grease feeds were determined. The rate constants for esterification are higher than the transesterification rate constants. The kinetic model was validated using the experimental biodiesel data obtained from processing a commercial yellow grease feed. The kinetic model could be used to design novel processes to convert various low-value waste oils, fats and non-food grade oils to sustainable biodiesel. Keywords: Yellow grease, Canola oil, Free fatty acids, Heteropolyacid, Kinetics for esterification and transesterification

Upwelling processes bring nutrient-rich waters from the deep ocean to the surface. Areas of upwelling are often associated with high productivity, offering great economic value in terms of fisheries. The sensitivity of spring/summer-time coastal upwelling systems to climate change has recently received a lot of attention. Several studies have suggested that their intensity may increase in the future while other authors have shown decreasing intensity in their equatorward portions. Yet, recent observations do not show robust evidence of this intensification. The Senegalo-Mauritanian upwelling system (SMUS) located at the southern edge of the north Atlantic system (12°N–20°N) and most active in winter/spring has been largely excluded from these studies. Here, the seasonal cycle of the SMUS and its response to climate change is investigated in the database of the Coupled Models Inter comparison Project Phase 5 (CMIP5). Upwelling magnitude and surface signature are characterized by several sea surface temperature and wind stress indices. We highlight the ability of the climate models to reproduce the system, as well as their biases. The simulations suggest that the intensity of the SMUS winter/spring upwelling will moderately decrease in the future, primarily because of a reduction of the wind forcing linked to a northward shift of Azores anticyclone and a more regional modulation of the low pressures found over Northwest Africa. The implications of such an upwelling reduction on the ecosystems and local communities exploiting them remains very uncertain.

Abstract The integrity of PWR pressure vessels is assured by keeping the crack tip stress intensity factor below the toughness of the material under monotonic isothermal loading. To study the effects of sudden cooling associated with a thermal gradient, a specially modified compact specimen has been developed. This has been used to carry out tests in the transition zone with different loading-temperature sequences liable to call the conventional criteria into question. The test is described in detail in Part I of this article [Chapuliot S, et al. Thermomechanical analysis of thermal shock fracture in the brittle/ductile transition zone. Part I: Description of the tests. Engng Fract Mech, 72, 2005, 661–73]. The second part describes numerical investigations to estimate the local mechanical fields at the crack tip and the overall parameters of the fracture mechanics. Finite element thermomechanical calculations are used to interpret the results of these new thermal shock tests using the master curve concept [ASTM E 1921–1997. Standard test method for determination of reference temperature To for ferritic steels in the transition range, 1997] and the Beremin statistical model [Beremin FM. A local criterion for cleavage fracture of a nuclear pressure vessel steel. Metall Trans A, 14A, November 1983, 2287–777].

Abstract This work aims to predict the general performances of a pilot parabolic trough collector during transient periods. To do so, a one-dimensional thermal model has been developed. It has been validated with experimental results from two different experimental setups, in steady-state conditions, with a transmitted power maximum error of 3.4%. Since the model only predicts the collector's thermal behavior, the parabolic trough collector has been first optically qualified. Then, optical efficiencies were used as input for the model. Experimental results were obtained in steady-state conditions and compared to the model. Then, experimental and numerical results were compared during two period of time with varying inlet conditions (i.e. dynamic condition tests): the first one with stable conditions, and the other one with harsh conditions. The developed model showed a good capability of predicting the thermal behavior of the parabolic trough collector with unstable environment (DNI, mass flow, inlet temperature), with a 9.6% relative standard error in the worst case. As a conclusion, while previous studies only focused on steady-state conditions, it has been showed that this kind of model can be used to precisely predict the dynamic behavior of large power plants.

Abstract This paper investigates the optimal choice of building energy efficiency (BEE) standard in the context of centralised urban district heating system in northern China. By employing a techno-economic analysis approach, we demonstrate that the current BEE standard implemented in the Chinese cities should be tightened further in order to achieve a socially optimal level. Without considering the externality costs associated with carbon dioxide (CO2) emissions, current BEE standards need to be upgraded to the equivalent level of French RT2005 standard coupled with a properly designed district coal-fired Combined Heat and Power (CHP). In contrast, the equivalent efficiency standard of Swedish building code is preferably to be implemented in the case of explicit carbon emission restriction as long as the marginal cost of carbon emission (carbon price) is sufficiently high. The fuel-switching policy (from coal to natural gas) in the urban district heating system would result in significant increase in overall costs if the BEE upgrade is not taken into account simultaneously. It is also found that BEE improvements in northern Chinese cities are more cost-effective than investing in low-carbon technologies such as wind power or Carbon Capture and storage in the EU and US with regard to CO2 emissions mitigation.

The assessment of voltage stability margins is a promising direction for wide-area monitoring systems. Accurate monitoring architectures for long-term voltage instability are typically centralized and lack scalability, while completely decentralized approaches relying on local measurements tend towards inaccuracy. Here we present distributed linear algorithms for the online computation of voltage collapse sensitivity indices. The computations are collectively performed by processors embedded at each bus in the smart grid, using synchronized phasor measurements and communication of voltage phasors between neighboring buses. Our algorithms provably converge to the proper index values, as would be calculated using centralized information, but but do not require any central decision maker for coordination. Modifications of the algorithms to account for generator reactive power limits are discussed. We illustrate the effectiveness of our designs with a case study of the New England 39 bus system. 10 pages, submitted for publication

Abstract Building-based active envelopes play an important role to reduce active heating supplies. Several techniques are developed to enhance the energy performances of active building envelopes; meanwhile, numerous numerical and mathematical models are also developed to conduct the performance analysis of these techniques. In this paper, we propose a state-space model for solar active wall-based Phase Change Materials (PCM). The advantage of this method remains in its simplicity to provide details of internal nodes and input/output parameters. The low-cost calculation is a supplementary advantage versus a heavy numerical method. The proposed numerical model is applied for a multi-layer wall with PCM Wallboards (PCMW) embedded between indoor and outdoor environments. The results show the ability of the state-space model to estimate the thermal behavior of the system, as well as the thermal characteristics of embedding PCM in the internal face of the wall. It significantly contributes to stabilize the indoor temperature and to ensure the thermal comfort.

Demand-Side Management systems aim to modulate energy consumption at the customer side of the meter using price incentives. Current incentive schemes allow consumers to reduce their costs, and from the point of view of the supplier play a role in load balancing, but do not lead to optimal demand patterns. In the context of charging fleets of electric vehicles, we propose a centralised method for setting overnight charging schedules. This method uses evolutionary algorithms to automatically search for optimal plans, representing both the charging schedule and the energy drawn from the grid at each time-step. In successive experiments, we optimise for increased state of charge, reduced peak demand, and reduced consumer costs. In simulations, the centralised method achieves improvements in performance relative to simple models of non-centralised consumer behaviour.