• Energy Research
• engineering and technology close
• 11. Sustainability close
• 6. Clean water close
• CA close
• FR close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Abstract This paper investigates the optimal choice of building energy efficiency (BEE) standard in the context of centralised urban district heating system in northern China. By employing a techno-economic analysis approach, we demonstrate that the current BEE standard implemented in the Chinese cities should be tightened further in order to achieve a socially optimal level. Without considering the externality costs associated with carbon dioxide (CO2) emissions, current BEE standards need to be upgraded to the equivalent level of French RT2005 standard coupled with a properly designed district coal-fired Combined Heat and Power (CHP). In contrast, the equivalent efficiency standard of Swedish building code is preferably to be implemented in the case of explicit carbon emission restriction as long as the marginal cost of carbon emission (carbon price) is sufficiently high. The fuel-switching policy (from coal to natural gas) in the urban district heating system would result in significant increase in overall costs if the BEE upgrade is not taken into account simultaneously. It is also found that BEE improvements in northern Chinese cities are more cost-effective than investing in low-carbon technologies such as wind power or Carbon Capture and storage in the EU and US with regard to CO2 emissions mitigation.

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.

Abstract The residential sector accounts for most of energy-consumption in developing countries in the form of traditional energy. The use of commercial energy is nominal and confined mostly to urban areas where fuelwood is already monetized. A model, based on an end-use/process analysis approach, is developed on a spreadsheet, which is capable of simulating scenarios to address issues of increasing traditional energy-demand caused by population growth, sustainable supply capacity of the existing energy resources, potential for development of new and renewable energy resources, technology. This paper is divided into two parts: general energy issues and the modelling approach, and the application of this approach to Nepal in the context of fuelwood-supply sustainability.

We study the determinants of PV adoption in the region of Flanders (Belgium), where PV adoption reached high levels during 2006-2012, because of active government intervention. Based on a unique dataset at a very detailed spatial level, we estimate a Poisson model to explain the heterogeneity in adoption rates. We obtain the following findings. First, local policies have a robust and significant impact on PV adoption, providing indirect evidence that the larger regional incentives formed the basis for the strong development of PV adoption in the region. Second, there is a strong unconditional income effect, implying a Matthew effect in the subsidization of PVs. Our third finding is however that this income effect is largely driven by the fact that wealthier households are more likely to adopt because they tend to be larger (and hence higher users), are more frequent house owners (who capture more of the benefits), or own houses that are better suited for PV. We can thus identify the channels through which wealthier households are more likely to benefit from the PV support. Finally, we identify the importance of several housing characteristics: PV adoption tends to be more likely in larger and in more recently built houses. In several extensions, we consider the determinants of the average size of installed PVs, and the differential impact of certain variables over time.

Abstract Bitumen recovery by steam-solvent coinjection involves the coupled thermal/compositional mechanisms for reduction of bitumen viscosity. Reliable design of such processes requires reservoir flow simulation based on a proper phase-behavior model so that the oleic-phase viscosity near the steam-chamber edge can be modeled reliably. However, the effect of bitumen characterization (e.g., the number of pseudo components used) on steam-solvent coinjection simulation has not been studied in detail, and can be realized only after running multiple reservoir simulations, which is time consuming. There are two main objectives in this paper. One is to develop a reliable method for bitumen characterization by improving the fluid characterization method that was recently developed based on perturbation from n-alkanes (PnA). The other is to develop a novel analytical method for assessing the sensitivity of a particular coinjection simulation to bitumen characterization without having to perform reservoir simulations. A simulation case study is given to validate this analytical method. A proper number of pseudo components for bitumen characterization cannot be determined without considering the effect of phase behavior on the oleic-phase viscosity at chamber-edge conditions in steam-solvent coinjection simulation. Results show that the analytical method developed in this research can detect the sensitivity of recovery simulation to bitumen characterization without performing multiple flow simulations using different sets of fluid models. The PnA-based method developed for bitumen characterization gives reliable predictions of phase behavior for bitumen/solvent mixtures with a small amount of experimental data.

Biodegradation of organic matter, including petroleum-based fuels and biofuels, can create undesired secondary water-quality effects. Trace elements, especially arsenic (As), have strong adsorption affinities for Fe(III) (oxyhydr)-oxides and can be released to groundwater during Fe-reducing biodegradation. We investigated the mobilization of naturally occurring As, cobalt (Co), chromium (Cr), and nickel (Ni) from wetland sediments caused by the introduction of benzene, toluene, ethylbenzene, and xylenes (BTEX) and ethanol mixtures under iron- and nitrate-reducing conditions, using in situ push-pull tests. When BTEX alone was added, results showed simultaneous onset and similar rates of Fe reduction and As mobilization. In the presence of ethanol, the maximum rates of As release and Fe reduction were higher, the time to onset of reaction was decreased, and the rates occurred in multiple stages that reflected additional processes. The concentration of As increased from <1 μg/L to a maximum of 99 μg/L, exceeding the 10 μg/L limit for drinking water. Mobilization of Co, Cr, and Ni was observed in association with ethanol biodegradation but not with BTEX. These results demonstrate the potential for trace-element contamination of drinking water during biodegradation and highlight the importance of monitoring trace elements at natural and enhanced attenuation sites.

Abstract Communication between vehicles and road infrastructure can enable more efficient use of the road network and hence reduce congestion in urban areas. This improvement can be enhanced by distributed control due to its lighter computational load and higher reliability. Despite favourable impacts on traffic, little is known about the effects of such systems on near-road air quality. In this study, an End-To-End (E2E) dynamic distributed routing algorithm in Connected and Automated Vehicles (CAVs) was applied in downtown Toronto, to identify whether benefits to network throughput were associated with lower near-road NO2 concentrations. We observe significant reductions in the emissions of Greenhouse Gases (GHGs) with increased penetration of CAVs. Nonetheless, at times, the emissions of nitrogen oxides (NOx) increased with higher CAVs. Besides, a higher frequency and severity of NO2 hot-spots were observed under a 100% CAV scenario. Impacts of the proposed system on electric energy consumption in a full electric vehicle network were also investigated, indicating that the addition of CAVs that are electric did not contribute to high energy savings. We propose that such new transformative technologies in transportation should be designed with air pollution and public health goals.

Abstract Conversion of carbon contained in the solid residues (tars + biochar) derived from urban biomass gasification named herein TC would allow enhancing the yield of carbon species (CO/CO2) in synthetic gas. For this purpose, three low cost materials have been tested as possible catalysts: iron species (reduced Fe), bone meal (BM), and ashes (ash) recovered from biochar complete oxidation. The parametric study used the following as variables: air GHSV, onset of reaction temperature, reaction time to optimize CO/CO2 molar ratio and tar content in the produced gas. Results showed an autocatalytic effect of biochar leading to the catalytic conversion of approximately 78% of tars by the native metals contained in TC. The catalytic effect was further enhanced by adding Fe, BM, and extra ash. Addition of Fe catalyst resulted in significant heat generation (temperature increase of ca. 500 °C) and a twofold decrease in reaction time to consume all the carbon. Use of ash and BM as catalysts exhibit heat generation comparable to Fe, along with an improved reaction time, complete tars conversion and a CO/CO2 molar ratio to above 1.3 in the produced gas.