• Energy Research
• Closed Access close
• Restricted close
• Embargo close
• 7. Clean energy close
• 12. Responsible consumption close
• 6. Clean water close
• CA close
• IR close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Among various bioreactors examined in anaerobic digestion and dark fermentation, UASB bioreactor has shown to be a promising alternative. However, mass transfer resistance and biomass washout have been the issues that reported as draw backs of the granular system in the literature. Another problem associated with such a system is its long start-up period as a result of biomass washout and long microbial granulation stage. In this paper, the results obtained from an UASFF bioreactor in methane (AD process) and hydrogen (DF process) production from POME, are presented to assess mass transfer of substrate into the granules and also study the role of internal packing used in the middle part of reactor in the process stability. The value of effectiveness factor, η, for AD and DF processes were calculated to be 0.96 and 0.94, respectively, indicating that there was no mass transfer resistance due to internal and/or external factors. The results showed that the packing material could retain biomass in the reactor and had outstanding contribution in the granulation enhancement. Its role as a supplementing treatment stage was more significant at low HRTs and up-flow velocities.

This paper presents a novel modified interactive honey bee mating optimization (IHBMO) base fuzzy stochastic long-term approach for determining optimum location and size of distributed energy resources (DERs). The Monte Carlo simulation method is used to model the uncertainties associated with long-term load forecasting. A proper combination of several objectives is considered in the objective function. Reduction of loss and power purchased from the electricity market, loss reduction in peak load level and reduction in voltage deviation are considered simultaneously as the objective functions. First, these objectives are fuzzified and designed to be comparable with each other. Then, they are introduced into an IHBMO algorithm in order to obtain the solution which maximizes the value of integrated objective function. The output power of DERs is scheduled for each load level. An enhanced economic model is also proposed to justify investment on DER. An IEEE 30-bus radial distribution test system is used to illustrate the effectiveness of the proposed method.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract In-core nuclear fuel management is one of the most important concerns in the design of nuclear reactors. Two main goals in core fuel loading pattern design optimization are maximizing the core effective multiplication factor in order to extract the maximum energy, and keeping the local power peaking factor lower than a predetermined value to maintain the fuel integrity. Because of the numerous possible patterns of fuel assemblies in the reactor core, finding the best configuration is so important and challenging. Different techniques for optimization of fuel loading pattern in the reactor core have been introduced by now. In this study, a software is programmed in C# language to find an order of the fuel loading pattern of a VVER-1000 reactor core using the perturbation theory. Our optimization method is based on minimizing the radial power peaking factor. The optimization process launches by considering an initial loading pattern and the specifications of the fuel assemblies which are given as the input of the software. The results on a typical VVER-1000 reactor reveal that the method could reach to a pattern with an allowed radial power peaking factor and increases the cycle length 1.1 days, as well.

Abstract The power system needs to satisfy its customers demand with minimum cost and emission. Fuel cost has straight relationship with energy cost. This paper presents an advanced parallelized particle swarm optimization algorithm (PSPSO) for finding optimal combination of power generation units that minimizes the total fuel cost and emission. In this algorithm, time requirements for solving complex large-scale CEED problem can be substantially reduced using parallel computation and it performs the update of positions and velocities in the end of each iteration. The proposed approach is applied on four test systems and compared with other techniques. The results represent that PSPSO has better convergence than other techniques.

Abstract Commercial potential in developing countries has always received a great attention from international investors, but this is not the case in Waste-to-Energy sector. Waste-to-Energy is bound up with various uncertainties rooted in its long-term nature therefore incorporating risks regarding political matters in developing countries makes it more complex. The present study substantiates the incompatibility of classic valuation methods in risky projects. Consequently, to deal with the riskiness of Waste-to-Energy investment in less developed countries, the combination of binomial tree analysis and Decoupled NPV is proposed. The hybrid approach is deployed to value a Waste-to-Energy project in Iran, and all evidence attest to the robustness of the method. The contribution of this paper can open up new vistas for investing in Waste-to-Energy industry, thus abating the catastrophic effects of landfill gas emissions.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

This paper presents an experimental study of indoor thermal environment near a full-scale glass facade with different types of shading devices under varying climatic conditions in winter. Interior glazing and shading temperature, operative temperature and radiant temperature asymmetry were measured for facade sections with roller shades and venetian blinds at different positions. Interior glass surface temperatures can be high during sunny days with low outdoor temperature. Shading systems significantly improved operative temperature and radiant temperature asymmetry during cold sunny days, depending on their properties and tilt angle. During cloudy days the impact was smaller, however the shading layers could still decrease the amount of heat loss through the facade. A transient building thermal model, which also calculates indoor environmental indices under the presence of solar radiation, was developed and compared with the experimental measurements. Part II of this paper uses this validated model with a transient, two-node thermal comfort model (including transmitted solar radiation) for assessment of indoor environmental conditions with different building envelope and shading properties, facade location and orientation.