• Energy Research
• Closed Access close
• CA close
• IT close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Changes in the main weather features are becoming perceivable in Italy. In the last years, the average temperature and the intensity of rainstorms are increasing. Such phenomena could lead to changes in the earth-atmosphere interaction. Accounting for the high vulnerability of the Italian territory, an obvious consequence would concern the effects on the hydro-geological hazards, including landslides and floods. As a matter of fact, the higher frequency of high magnitude flood and landslide events represent an alarm bell. It is necessary to explore with all available instruments the consequences of the potential climate changes. Since quantitative predictions are not possible, the only way to run is depicting rational scenarios for the most vulnerable contexts adopting a multidisciplinary approach. Based on projections of potential climate changes in the 21st century, the report examines their potential impact in the context of the Italian peninsula. After a general overview about typical slope responses to weather changes, some quantitative scenarios have been depicted for representative geomorphological contexts. The last part of the paper examines changes in the expected risk, based on the characteristics of the Italian territory and its vulnerability, looking at the initiatives to undertake for its mitigation.

The electrical resistance of Ni 50 Ti 30 Hf 20 and Ni 50 Ti 40.5 Hf 9.5 alloys during Stress Assisted Two Way Memory Effect was investigated with the aim to deduce the relationship between electrical resistance and deformation across the transformation range. Results show an almost linear relationship although a crossing point between increasing and decreasing deformation may compromise the use of these alloys actuators.

A detailed analysis of the effects of ground grid configuration on grounding performance has been carried out for uniform and horizontally stratified soils with multiple layers. The results of the analysis reveal that the most efficient and cost-effective design is highly dependent on soil structure type and characteristics. In the absence of ground rods, grounding grids with uniform mesh size are quite efficient in soils having a thin (relative to grid size) high resistivity (relative to the lower layers) top soil, while grids with small mesh size at the periphery of the grid provide optimum performance in uniform soils and soils with low resistivity top soils. Ground rods were found to be effective only when a significant portion of their length is in contact with a low resistivity soil, as expected.

Experiments were carried out to determine the accuracy and validity of estimations of hepatic blood flow from systemic clearances of ethanol during very low dose (8 μmol∙min−1∙kg−1) infusions of ethanol in anesthetized cats. Systemic clearances were compared with directly measured hepatic blood flow using a hepatic venous long-circuit technique. This technique allowed direct measurement and alteration of hepatic blood flow and collection of arterial, portal, and hepatic venous blood samples without depletion of the animal's blood volume. In 18 cats, Vmax for ethanol was 93 ± 7 μmol∙min−1 per 100 g liver or 21 ± 2 μmol∙min−1∙kg·body weight−1 and Km was 144 ± 19 μM in terms of logarithmic mean sinusoidal concentration. At the dose of 8 μmol∙min−1∙kg body weight−1 used for estimation of hepatic blood flow, extraction was 0.95 ± 0.07 (mean ± SD). Systemic clearance of ethanol overestimated directly measured hepatic blood flow by 15 ± 16%. Hepatic blood flow changes expressed as percentages of the control level were accurately estimated from systemic ethanol clearance (100 ± 10%). Since 73 ± 12% of the infused ethanol was eliminated by the liver and 83 ± 11% was eliminated by the splanchnic bed, an extrasplanchnic uptake of 17% accounted for the overestimation of hepatic blood flow. Estimation of hepatic blood flow from systemic clearances of ethanol during very low dose infusions may have advantages over other clearance methods. Its use in cats was illustrated in a separate series of experiments and it was shown that surgery significantly reduced hepatic blood flow. The method may merit trial for estimation of hepatic blood flow in humans.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract Bio-based polyurethane (BPU) foams were successfully prepared using hydrothermally liquefied wheat straw (WS) to substitute a mass fraction of up to 50% of polyols. Response surface methodology (RSM) based on central composite design (CCD) was employed to optimize four process parameters: NCO/OH molar ratio, loading of crosslinking agent (glycerol), loading of catalyst (a mixture of triethylene diamine, stannous octoate, and triethanolamine), and loading of blowing agent (water) for the maximum compression strength of the rigid BPU foams. With the quadratic orthogonal regression model, verified by experimentation, the maximum compression strength of approximately 180 kPa was obtained at the following optimal conditions: NCO/OH molar ratio of 1.24:1, glycerol addition of 12.11%, catalyst loading of 0.76%, and blowing agent addition of 1.31% in relation to the total mass of polyols. The BPU foam prepared at the optimal conditions exhibits good thermal conductivity (0.045 Wm−1K−1) and thermal stability, comparable to those of a reference foam prepared with 100% PPG400.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.