• Energy Research
• Closed Access close
• Embargo close
• 7. Clean energy close
• 12. Responsible consumption close
• CA close
• IT close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

The crucial role evaluation can play in the co-development of project design and its implementation will be addressed through the analysis of a case study, the Green Communities (GC) project, funded by the Italian Ministry of Environment within the EU Interregional Operational Program (2007-2013) "Renewable Energy and Energy Efficiency". The project's broader goals included an attempt to trigger a change in Italian local development strategies, especially for mountain and inland areas, which would be tailored to the real needs of communities, and based on a sustainable exploitation and management of the territorial assets. The goal was not achieved, and this paper addresses the issues of how GC could have been more effective in fostering a vision of change, and which design adaptations and evaluation procedures would have allowed the project to better cope with the unexpected consequences and resistances it encountered. The conclusions drawn are that projects should be conceived, designed and carried out as dynamic systems, inclusive of a dynamic and engaged evaluation enabling the generation of feedbacks loops, iteratively interpreting the narratives and dynamics unfolding within the project, and actively monitoring the potential of various relationships among project participants for generating positive social change.

Abstract Economically harvesting energy from a microbial fuel cell (MFC), increasing its electrical power production, and developing its role as a practical energy supply, needs a low-cost and high-performance design of the MFC compartments. According to this strategy, a novel monolithic membrane electrode assembly (MEA) was fabricated and evaluated as an air–cathode in a single-chamber MFC (SCMFC). The MEA was made of bacterial cellulose (BC), conductive multi-walled carbon nanotubes (CNT), and nano-zycosil (NZ). BC, as a nano-celluloses with oxygen barrier property, can maintain anaerobic conditions for the anode compartment. Binder-less CNT coating on BC avoids costly binders such as poly-tetra fluoro ethylene (PTFE) and Nafion and decreases the MEA charge transfer resistance. NZ, as a very cheap modifier, not only prevents the anolyte leakage but also provides more MEA’s active sites for the oxygen reduction reaction (ORR). The electrochemical performance of the MEA was compared to a PTFE- based gas diffusion electrode (GDE) in the SCMFC. The MEA cell provided a pulse power density of 1790 mW/m2, roughly twice as high as the pulse power density of GDE (920 mW/m2). SCMFC’s internal resistance decreased from 1.84 KΩ (with GDE) to 0.8 KΩ (with MEA). Also, the cell’s columbic efficiency increased from 4.2% (with GDE) to11.7% (with MEA). Additionally, the capacitance of the MEA (65 mF) was much higher than the value for GDE (0.73 mF). Thus, the MEA compared to the GDE showed higher performance in the SCMFC for electricity generation and wastewater treatment at a lower cost.

Abstract This article focuses on the results obtained by the enforcement of a original greenhouse gas emissions policy, issued in recent years in several municipalities in Northern Italy. The Municipality of Reggio Emilia was one of the firsts in Italy to develop and adopt a voluntary building energy-consumption certification method called Ecoabita, aiming to promote energy efficiency in buildings over its jurisdiction. Several reasons make this project innovative: first, the certification method has been processed through and verified by a quality international agency, secondly the procedure is assisting financial-incentive policies both on mandatory (European Directive 2002/91/CE) and voluntary basis (Municipality Protocol Ecoabita), finally it allows to obtain eligible credits for avoided emissions that can be negotiated on the CO2 exchange market. With specific reference to Reggio Emilia case, acknowledged the amount of actions, that are normally scheduled in the municipality throughout a year, it has been evaluated the benefit, in terms of environmental improvement, descended from the protocol, also projecting their trend in future years up to 2020 as well, demonstrating the scheduled interventions are fundamental in sought of the achievement of the Kyoto and Copenhagen commitments. The entire procedure has been developed in accordance to the parameters given by UNFCCC for these kinds of analyses and has been recently confirmed to be one of the most accurate international accounting procedure by a survey developed by the scientific committee of the European Project LIFE-LAKS.

This paper presents an experimental study of indoor thermal environment near a full-scale glass facade with different types of shading devices under varying climatic conditions in winter. Interior glazing and shading temperature, operative temperature and radiant temperature asymmetry were measured for facade sections with roller shades and venetian blinds at different positions. Interior glass surface temperatures can be high during sunny days with low outdoor temperature. Shading systems significantly improved operative temperature and radiant temperature asymmetry during cold sunny days, depending on their properties and tilt angle. During cloudy days the impact was smaller, however the shading layers could still decrease the amount of heat loss through the facade. A transient building thermal model, which also calculates indoor environmental indices under the presence of solar radiation, was developed and compared with the experimental measurements. Part II of this paper uses this validated model with a transient, two-node thermal comfort model (including transmitted solar radiation) for assessment of indoor environmental conditions with different building envelope and shading properties, facade location and orientation.

Abstract Probability density functions (PDFs) are normally used to describe wind speed distribution for the proper selection of wind turbines in a given location. The identification of a suitable PDF is fundamental for accurately assessing the wind energy potential and designing the wind farms. To achieve this objective, the use of a mixture of two truncated normal distributions (MTTND), defined for v ≥ 0 and obtained by linearly combining two normal distributions with different means and variances, is proposed in this work for the representation of the wind speed PDF. The distribution is a function of five parameters, does not require a high computational burden and allows the representation of wind calm hours (v = 0). The use of the MTTND allows an accurate estimation to be obtained of the experimental discrete distribution of the probability density and cumulative probability, and the characteristic statistical quantities used to estimate the available energy and the performance indicators in the selection of both the site and wind turbine. The validity of the use of the MTTND was verified by comparison with the most widespread PDFs in the scientific literature: Weibull, Rayleigh, lognormal, gamma, inverse Gaussian and Burr. This comparison was developed using experimental wind speed data relating to five Italian locations and a location in Colorado (USA) belonging to the National Renewable Energy Laboratory. For each location, the parameters of each PDF were obtained with the least squares non-linear regression method. The results of the comparisons, in terms of the coefficient of determination R2 and root mean square error (RMSE) for goodness of fit and in terms of relative error in the calculation of the statistical quantities, show that the use of the MTTND gives rise to greater accuracy than a conventional wind speed PDF.

Abstract Reaching universal access to electricity by 2030 requires a massive deployment of mini-grids in rural areas of developing countries. Among the many challenges hindering this process, there are the high uncertainties in assessing demand patterns in rural communities, the costs of field survey campaigns, and the absence of ample and reliable datasets coming from existing projects. This paper tries to address these issues by presenting and discussing a database of load profiles from sixty-one off-grid mini-grids from developing countries worldwide, gathered from the literature, private developers and fieldworks, and reported with technical, socio-economic and geographical characterization factors. A clustering procedure led to the identification of five archetypal load profile clusters, which are presented and analyzed together with their load duration curves. Subsequently, the distribution among the clusters of the various characterization factors selected is studied. The proposed approach allows to widen the range of load profiles usually considered, and to seek correlations between the load profile shapes, the peak power and average energy consumption per connection, the number of customers, the age of measurement, geographical position, operator model, type of tariff and generation technologies present. This work establishes a first step in the creation of a shared database for load profiles of rural mini-grids, helping to overcome the lack of available data and difficulties of demand assessment, proposing original insights for researchers to understand load patterns, and contributing to reduce risks and uncertainties for mini-grid developers.

Energy management is an enabling technique to guarantee the reliability and economy of hybrid electric systems. This paper proposes a novel machine learning-based energy management strategy for a hybrid electric bus (HEB), with an emphasized consciousness of both thermal safety and degradation of the onboard lithium-ion battery (LIB) system. Firstly, the deep deterministic policy gradient (DDPG) algorithm is combined with an expert-assistance system, for the first time, to enhance the “cold start” performance and optimize the power allocation of HEB. Secondly, in the framework of the proposed algorithm, the penalties to over-temperature and LIB degradation are embedded to improve the management quality in terms of the thermal safety enforcement and overall driving cost reduction. The proposed strategy is tested under different road missions to validate its superiority over state-of-the-art techniques in terms of training efficiency and optimization performance.