• Energy Research
• 2016-2025close
• CA close
• UA close

Енергоефективність та енергозбереження є пріоритетним напрямком розвитку науки, технологій і техніки в Україні. Проведена в усьому світі політика енергозбереження спрямована на всі галузі і наукові дослідження в усіх сферах. Значним споживачем енергоресурсів є заклади вищої освіти. Актуалізація нормативно-правової та технічної бази, спрямованих на проектування і експлуатацію будівель з низьким рівнем енергоспоживання і високим класом енергоефективності свідчить про необхідність короткострокового вирішення проблеми. При цьому має місце відсутність системного погляду на енергоефективність, що не дозволяє оцінити рівень витрат енергоресурсів на всьому протязі життєвого циклу закладів вищої освіти, що показує необхідність пошуку ефективних шляхів вирішення проблеми. Для оцінки впливу факторів на електроспоживання та енергоефективність Київського національного університету технологій та дизайну було використано метод множинної регресії, проведений статистичний аналіз отриманих даних. В результаті вдалося з'ясувати, що дані електроспоживання не підкоряються закону нормального розподілу, тому побудувати точний прогноз електроспоживання важко. Використання ХАБ знань з енергоефективності дозволило провести більш якісний аналіз і виділити основні фактори, що впливають на електроспоживання. Університет має нерегульоване центральне опалення, системи індивідуального кондиціонування, а також центрального та індивідуального освітлення. У зв'язку з цим для проведення енергетичного моніторингу і енергоаудиту будівель університету було обрано такі основні фактори: середня температура повітря на вулиці, середня тривалість світлового дня, опалювальний період, середня кількість осіб, які працюють в день, протягом місяця. Впровадження запропонованої схеми структурної організації типової системи автоматичного обліку енергоспоживання університету на базі університетського ХАБ знань з енергоефективності: серверу, що дозволяє збирати, зберігати і обробляти дані; маршрутизатори за допомогою різних провідних і бездротових технологій ...

To mitigate the temperature increase in urban environments and reduce its impact on energy consumption and the quality of the environment, urban retrofitting technologies have been developed and applied worldwide. High albedo in urban surfaces and additional vegetation are the most efficient strategies to accomplish these goals. The objective of this study is to estimate the weight of these strategies, both individually and integrated, on the cooling potential of two Latin American cities. To do this, 36 low and high urban density scenarios were simulated with the ENVI-Met software. The simulation models were calibrated using air temperature curves which were monitored during the summer periods from 2010 to 2013. A Principal Components Analysis was carried out to establish possible associations between the proposed mitigation strategies and then the weight of anthropogenic heat was evaluated according to the configuration. The results show that the integrated mitigation strategies in urban areas -i. e. increase vegetation and albedo on horizontal surfaces- has a great potential to mitigate urban warming, showing a more significant impact on low-density urban configuration. The contribution of anthropogenic heat mainly produced by motorized transport and air conditioning systems, is a crucial input data for the urban microclimate simulations. Its impact on the urban densification processes may cancel out the benefits derived by the application of the mitigation strategies considered.

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.

Abstract The adoption rate and stringency of building energy standards in the U.S. have been increasing since the mid-1990s as a result of the Energy Policy Act mandate of 1992 (EPAct). Current evidence on the energy savings that accrue from commercial building energy standards is based on engineering simulations, which do not account for realized behaviour once a standard is actually adopted. This paper uses quasi-experimental variation in commercial building energy standard adoptions to estimate their effect on realized electricity consumption and cost-effectiveness. In states induced by EPAct to adopt an energy standard where all new nonresidential construction was erected under a commercial standard, electricity consumption per service worker is lower by about 12%, and total commercial electricity consumption is lower by 10%. Including early adopters and never-adopters to the analysis leads to a downward bias in the treatment effect. The realized electricity savings in the EPAct states represent three quarters of predicted simulated savings, and electricity saved in 2010 came at a cost of approximately 7.7 cents per kWh.

Abstract For 118 million residential housing units in the U.S., there is currently a gap between the potential energy savings that can be achieved through the use of existing energy efficiency technologies, and the actual level of energy savings realized, particularly for the 37% of housing units that are considered residential rental properties. Additional quantifiable benefits are needed beyond energy savings to help further motivate residential property owners to invest in energy efficiency upgrades. This research focuses on assessing the adoption of energy efficient upgrades in U.S. residential housing and the impact on rental prices. Ten U.S. cities are chosen for analysis; these cities vary in size across multiple climate zones, and represent a diverse set of housing market conditions. Data was collected for over 159,000 rental property listings, their characteristics, and their energy efficiency measures listed in rental housing postings across each city. Following an extensive data quality control process, over thirty different types energy efficient features were identified. The level of adoption was determined for each city, ranging from 5.3% to 21.6%. Efficient lighting and appliances were among the most common, with many features doubling as energy efficient and other desirable aesthetic or comfort improvements. Then using propensity score matching and conditional mean comparison methods, the relative impact on rent charged in each city was calculated, which ranged from a 6% to 14.1% increase in rent for properties with energy efficient features, demonstrating a positive economic impact of these features, particularly for property owners. This was further subdivided into five types of energy efficiency upgrade and three housing types. Single family homes generally demanded higher premiums with energy efficient features, however there was not a consistent pattern across the types of efficient upgrades. The results of this work demonstrate that investment in energy efficient technologies has quantifiable benefits for rental property owners in the U.S. beyond just energy savings. This methodology and results can also be used in other cities and by property owners, utility companies, or others, ultimately encouraging further investment and positive economic impact in residential energy efficiency and in turn improving energy and resource conservation in the building sector.

Abstract A new formulation for the evaporation, flashing, condensation processes taking place in the effects of thermal desalination systems which simulates the operation of both forward and parallel/cross configurations is coupled with an exergo-economic model based on the SPECO method. The thermo-economic model uses accurate properties for the seawater, brine, pure water and vapour and is solved with an equation solver which does not require the development of a specific solution algorithm as in most previous studies. This flexible model is used to analyze the influence of the number of effects N and the temperature difference ΔT e between effects on the technical and economic performance of multi-effect desalination systems with ejector vapour compression. In particular, it is shown that the performance calculated by an earlier black-box approach is not attainable by technically and economically realistic systems. It is also shown that for each feed configuration and a given number of effects there exists an optimum value of ΔT e which minimizes the cost of the produced potable water. This last result forms the basis of a procedure that combines black-box results with the optimum value of ΔT e and can be used to select the appropriate system for any specific application.