• Energy Research
• Closed Access close
• Open Source close
• 6. Clean water close
• 15. Life on land close
• 2. Zero hunger close
• 14. Life underwater close
• US close
• CA close

A prototype air cycle cooling system, designed for forced cooling of HPOF pipe-type cable, was built under an EPRI contract. Its main components are a turbine and compressor operated on a single high speed shaft and a compact cable. oil to air heat exchanger. Air cooling is supplemented by a spray water system. Tests were conducted on the prototype unit at the EPRI Waltz Mill Cable Test Facility to evaluate its performance and operating characteristics. This paper briefly describes this equipment and presents the results of the test program.

Abstract Fouling is one of the most significant problems for internally enhanced tubes installed in the shell and tube condensers. Due to the lack of long-term test data, current fouling models are developed based on accelerated particulate fouling tests that have the low precision and hence are inapplicable for predicting combined fouling in most practical cooling tower systems. In addition, the constant values of fouling resistance (factor) recommended by the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) are extremely limited under different operating conditions. To overcome these challenges, this research developed and validated two fouling prediction models based on experimental long-term tests. One of the models was in the form of a ratio of asymptotic fouling resistance of the enhanced tube to that of the plain tube ( R f ∗ / R f , p ∗ ), and the other one was in the form of the asymptotic fouling resistance of the directly enhanced tube ( R f ∗ ). Both models considered water quality, water velocity, and the tube geometries as the variables with the acceptable accuracy for prediction. 1) For the water quality, the parameter of valid concentration ( C com ) of cooling water was defined in this study, which reflected the potential amount of valid components to form the fouling. 2) For the water velocity, its impacts on the two critical parameters of the fouling process: sticking probability ( P ) and deposit bond strength ( ξ ) were investigated using experimental studies. Test results showed that in enhanced tubes with the increased water velocity the sticking probability ( P ) decreased continuously while the deposit bond strength (ξ) initially increased, and then, decreased. 3) For the tube geometries, by taking the parameters of tube geometries as variables the multi-variable correlations of the sticking probability ( P ) and deposit bond strength ( ξ ) were developed. From the results the generalized fouling prediction model as a ratio of asymptotic fouling resistance ( R f ∗ / R f , p ∗ ) was recommended for the application in HVAC&R industry due to its suitability and accuracy in practical project applications.

The natural hydrology of streams and rivers is being extensively modified by human activities. Water diversion, dam construction, and climate change have the potential to increase the frequency and intensity of low-flow events. Flow is a dominant force structuring stream aquatic insect communities, but the impacts of water diversion are poorly understood. Here we report results of an experimental stream flow diversion designed to test how aquatic insect communities respond to a low-flow disturbance. We diverted 40% to 80% of the water in three replicate streams for three summers, leading to summer flow exceedance probabilities of up to 99.9%. Shifts in habitat availability appeared to be a major driver of aquatic insect community responses. Responses also varied by habitat type: total insect density decreased in riffle habitats, but there was no change in pool habitats. Overall, the total biomass of aquatic insects decreased sharply with lowered flow. Collector-filterers, collector-gatherers, and scrapers were especially susceptible, while predatory insects were more resistant. Despite extremely low flow levels, there was no shift in aquatic insect family richness. The experimental water withdrawal did not increase water temperature or decrease water quality, and some wetted habitat was always maintained, which likely prevented more severe impacts on aquatic insect communities.

Abstract Survival, height and diameter for the first four year rotation were measured on two intensively cultured Populus hybrid plantations in central Pennsylvania. Treatments of control, irrigation, fertilization and fertilization/irrigation were installed on two sites and in two establishment years. Overall treatment survival was not affected by site but values were lower for 1980 planted trees (83%) than 1981 planted trees (90%). Survival values among the treatments were similar until the later ages of the first rotation. Treatments with fertilizers had lower four-year-old survival (78%) than the treatments without fertilizers (86%). The four-year-old control trees averaged 5.3 and 6.8 m in height, and 3.4 and 4.2 cm in diameter for the 1980 and 1981 establishment years, respectively. Fertilization, with or without irrigation, consistently increased annual height and diameter over the control. Fertilization/irrigation did not result in tree size values that were greater than fertilization. In general, there were inconsistent increases in annual height and diameter from irrigation.

Abstract Renewable energy sources (RES) coupled to desalination offers a promising prospect for covering the fundamental needs of power and water in remote regions, where connection to the public electrical grid is either not cost effective or not feasible, and where the water scarcity is severe. Stand-alone systems for electricity supply in isolated locations are now proven technologies. Correct matching of stand-alone power supply desalination systems has been recognized as being crucial if the system is to provide a satisfactory supply of power and water at a reasonable cost. The paper covers plants installed since 1990 on the coupling of the two technologies. The main driver promoting the take up of this technology is that water is a limiting factor for many countries in the Mediterranean region. This paper presents the two technologies, RES desalination, and describes the most promising couplings such as PV–reverse osmosis, wind-mechanical-vapor compression, geothermal-multieffect distillation, etc as well as technologies selection guidelines. Also, included applications and lessons learned from specific applications as well as data on the economics. RES for desalination is an important challenge and useful work has been done. However in order to provide practical viable plants, much remains to be done.

SummaryStudies investigated the patient‐care (in‐hospital) and outside‐the‐hospital energy consumptions for delivering the hemodialysis (HD) service. A life cycle inventory methodology was used for this patient‐based analysis for two hospitals located in Wichita, Kansas. It was found that, for both hospitals, the actual HD machines consumed approximately 3.5 kilowatt‐hours (kWh) of electrical energy per HD, only 8% to 16% of the total energy used for delivering the HD service (in hospital). This increases to 9.6 to 28.9 kWh of hospital billable energy for the whole system of HD machine, auxiliaries, and dialysis water treatment. Converting these hospital direct electrical energy values to natural resource energy (nre) then adding the cradle‐to‐gate natural resource energy for the manufacturing and supply chain of all the HD consumables, the total is 78 to 149 kWh nre/HD. The nre measures all the direct fuel burned to generate energy and is thus directly related to emissions to the air, water, and land and is a direct secondary impact on public health from HD. The ratio of outside‐the‐hospital energy to direct hospital HD electrical energy consumption is 4:1 to 7:1, so a broader base exists for improvement than just the hospital.

Abstract Hydraulic ram pump (HRP), also known as hydram, lifts water without using external power input. Its low performance combined with affordability of fuels has put this otherwise longstanding technology in the backburner of science and research for a long time, yielding to electric or fuel powered pumps. However, growing concerns about the impacts of fossil fuel use on the environment as well as the rising price of electricity has generated a renewed interest in such technology. The ram pump's operation in remote areas where power grid is not available adds research value on the technology. In this project, a novel approach, i.e., adding thermal energy to the flow to assist the water hammer pressure was modeled. Computational fluid dynamics (CFD) simulation was conducted using ansys. The results were validated experimentally in a 32 mm (27 mm internal diameter) drive pipe and a supply head of 2.18 m ram pump. The Analytical approach was more conservative. The results between simulation and experiment were fairly consistent, with only 6.99% error for pressure, and 10.16% for flowrate. The results show that pressure increased from 183.33 kPa to 342.32 kPa when thermally assisted to reach 150 °C. The experimental discharge flow increased from 11.72 l/min to 16.41 l/min for the corresponding temperature, a 42.01% increase.

Electron microscopic appearance of the liver sinusoid was examined in rats fed alcohol chronically in a complete liquid diet or in sucrose‐containing drinking water. The animals were kept on liquid diet (±alcohol) for 14 weeks or on sucrose‐containing drinking water (±alcohol) for 12.5 weeks and sacrificed thereafter. To rule out possible artifact induced by fixation procedure, livers were fixed by immersion (no perfusion), immersion preceded by perfusion, and by perfusion with glutaraldehyde and examined with both scanning and transmission electron microscopy. Regardless of the mode of its administration, and of the fixation procedure used, alcohol induced similar changes in liver sinusoid ultrastructure. Such changes included disruption of the sieve‐plate pattern of the sinusoidal endothelial cell fenestrations with the appearance of large gaps and resulting in a meshwork lining, wherein large areas of the sinusoid communicated freely with the underlying hepatocytes. Transmission electron microscopy complemented these findings. The results reported in this study demonstrate that alcohol‐induced structural changes of the liver sinusoid in the rat are similar whether alcohol is fed via a liquid diet or in drinking water. Therefore, alcohol administration in drinking water may provide a simple, inexpensive, and convenient method of inducing structural changes in the rat liver sinusoid.

The objective of this study was to determine effects of drought on selected root growth parameters and develop relationships between root parameters and tuber yield for selected Jerusalem artichoke (JA) genotypes. Three water regimes (Field capacity, 50% available soil water (AW) and 25% AW) and five JA varieties (JA 60, JA 125, JA 5, JA 89 and HEL 65) were planted with factorial treatments in a randomized complete block design with four replications. Data on root dry weight (RDW) and root: shoot ratios (RSR) were measured manually. Root diameter (RD), root length (RL), root surface area (RSA) and root volume (RV) were collected at harvest. Drought tolerance indices (DTI) were calculated for all root parameters. Drought reduced all root parameters and DTI but increased RSR in JA 60, JA 125, JA 5, and HEL 65. JA 125 had high values for all root traits and DTI of these traits under drought stress. JA 60 had high DTI of RDW, RD and RSR under mild and severe water stress. JA 5 had high DTI of RDW, RD, RL, RSR and RV under drought conditions. JA 89 and HEL 65 performed well for RDW, RD, RL and low DTI of all root characteristics. DTI for root parameters were positively correlated with tuber dry weight under mild and severe water stress. The JA 5, JA 60 and JA 125 varieties showed high DTI for some root traits, indicating that better root parameters contributed to higher tuber yield under drought stress.