• Energy Research
• Open Access close
• engineering and technology close
• CA close

To mitigate the temperature increase in urban environments and reduce its impact on energy consumption and the quality of the environment, urban retrofitting technologies have been developed and applied worldwide. High albedo in urban surfaces and additional vegetation are the most efficient strategies to accomplish these goals. The objective of this study is to estimate the weight of these strategies, both individually and integrated, on the cooling potential of two Latin American cities. To do this, 36 low and high urban density scenarios were simulated with the ENVI-Met software. The simulation models were calibrated using air temperature curves which were monitored during the summer periods from 2010 to 2013. A Principal Components Analysis was carried out to establish possible associations between the proposed mitigation strategies and then the weight of anthropogenic heat was evaluated according to the configuration. The results show that the integrated mitigation strategies in urban areas -i. e. increase vegetation and albedo on horizontal surfaces- has a great potential to mitigate urban warming, showing a more significant impact on low-density urban configuration. The contribution of anthropogenic heat mainly produced by motorized transport and air conditioning systems, is a crucial input data for the urban microclimate simulations. Its impact on the urban densification processes may cancel out the benefits derived by the application of the mitigation strategies considered.

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.

Abstract In the present study, Loblolly pine biomass residue was converted to bio-oil in a two-step process, consisting of 1) fast pyrolysis in the presence of zeolite ZSM-5 as a catalyst to produce pyrolysis oil, 2) hydrogenation of pyrolysis oil using formic acid as the hydrogen source in presence of Ru/activated carbon catalyst. Pyrolysis oils were analyzed by 13C, 31P and HSQC-NMR and the results revealed that the zeolite-induced catalytic fast pyrolysis process led to effective demethoxylation, producing more catechol and p-hydroxy-phenyl hydroxyl groups in the bio-oils, resulting in a decrease in the methoxyl group content by about 85 % and rich aromatic structures in the pyrolysis oils. The properties of pyrolysis oil with and without zeolite were in the bio-oil range. Hydrogenated pyrolysis oil showed that 79 % of the aromatic protons are eliminated and 87 % of protons are aliphatic in nature, with no oxygen attached to the α-carbon.

Exterior insulation finishing systems (EIFSs) can efficiently promote energy efficiency of buildings. In this study, an EIFS with high thermal efficiency is presented to improve the insulation behavior of building enclosure. Based on heat transfer analysis results, energy simulations of buildings with fire spread prevention structures were performed. Results revealed that heat flow through the wall increased by 10.3 % when using a metal rail to fix the insulation; in contrast, using non-combustible phenolic foam reduces heat flow by 37.4 %, satisfying the requirement for fire spread prevention structures. Additionally, the energy consumption decreased by 8.8 % when both mineral wool and phenolic foam were applied. Fire spread prevention structures are essential to improve the fire safety performance of buildings. This external insulation system efficiently promote energy saving in building; additionally, leveraging a phase change material to improve the thermal storage performance of the building can reduce energy consumption by up to 11.9 %.

The poultry industry is one of the largest and fastest growing sectors of livestock production in the world. The estimated 2010 world flock was over 18 billion birds with a yearly manure output of 22 million tonnes. Storage and disposal of raw poultry manure has become an environmental problem because of the associated air, water and soil pollution. Environmental and health problems such as odor and pathogens that may arise during and after land application of raw manure can be eliminated by drying. Dried manure can be utilized as a soil conditioner to improve soil tilth and reduce the problems associated with soil compaction and as a feed for ruminants because of its high nitrogen content. The aim of this study was to investigate the kinetics of thin layer drying of poultry manure and evaluate the effects of drying with heated air on the chemical and biological properties of manure. The effects of temperature and depth of manure layer were evaluated. The profile of the moisture content of poultry manure followed an exponential decay curve. The moisture decay constant was affected by the drying temperature and the depth of the manure layer. At the three temperature levels studied, the time required to dry poultry manure in 1 cm-deep layer was the least, followed by 2 and 3 cm-deep layers, respectively. The diffusion coefficient increased with both temperature and depth of drying layer, but did not show a linear increase with either variable. The optimum depth for drying manure (at which the highest drying effectiveness occurred) was 3 cm. Drying manure at 40-60°C resulted in the loss of 44-55% of the total Kjeldahl nitrogen, with losses increasing with both the temperature and depth of manure. The pH of the manure decreased from the initial value of 8.4 before drying to about 6.6 after drying. The odor analysis indicated that dried poultry manure did not have an offensive odor. Drying achieved 65.3 and 69.3% reductions in odor intensity and offensiveness, respectively. Reductions in the number of bacteria, mold/yeast and E.coli were 65-99, 74-99 and 99.97% respectively. The greatest reductions in microbial population occurred at the highest temperatures (60°C) and the thinest manure depths (1 cm). Heated air drying of poultry manure at temperatures between 40 and 60°C was effective in killing pathogens and removing odor.

AbstractUptake of electric vehicles is accelerating as governments around the world aim to decarbonize transportation. However, swift and widespread electric vehicle (EV) adoption will require some degree of controlled charging to mitigate the adverse impacts of electric vehicle adoption. Simulating the interaction between transportation and power requires new modelling tools with operational detail and spatial-temporal granularity. This analysis evaluates the potential benefits of utility-controlled charging (UCC) with the objective of reducing variable renewable energy (VRE) curtailment in decarbonized power systems using a framework that links travel and power system models using an intermediate charging model. Results show that the addition of VRE generation infrastructure shows the most impact on electricity system operating emissions and costs, but EV charging plays a significant role as well. Within EV charging strategies, UCC charging decreases emissions by 7% compared to uncontrolled charging. UCC is proven to be most effective in the summer due to higher electric vehicle fuel economy. Finally, the type of VRE generation infrastructure on the grid may have implications for siting of EV charging infrastructure due to the typical temporal peaks of wind and solar energy. These findings demonstrate how the use of distinct but linked travel and power sector models can be deployed to reduce multi-sector emissions and costs.

Carbon capture, utilization, and storage (CCUS) is a gas injection technology that enables the storage of CO2 underground. The aims are twofold, on one hand to reduce the emissions of CO2 into the atmosphere and on the other hand to increase oil/gas/heat recovery. Different types of CCUS technologies and related engineering projects have a long history of research and operation in the USA. However, in China they have a short development period ca. 10 years. Unlike CO2 capture and CO2-EOR technologies that are already operating on a commercial scale in China, research into other CCUS technologies is still in its infancy or at the pilot-scale. This paper first reviews the status and development of the different types of CCUS technologies and related engineering projects worldwide. Then it focuses on their developments in China in the last decade. The main research projects, international cooperation, and pilot-scale engineering projects in China are summarized and compared. Finally, the paper examines the challenges and prospects to be experienced through the industrialization of CCUS engineering projects in China. It can be concluded that the CCUS technologies have still large potential in China. It can only be unlocked by overcoming the technical and social challenges.