• Energy Research
• 12. Responsible consumption close
• 6. Clean water close
• 2. Zero hunger close
• 1. No poverty close
• CN close
• AU close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

The microbial electrolysis desalination and chemical-production cell (MEDCC) is a device to desalinate seawater, and produce acid and alkali. The objective of this study was to enhance the desalination and chemical-production performance of the MEDCC using two types of stack structure. Experiments were conducted with different membrane spacings, numbers of desalination chambers and applied voltages. Results showed that the stack construction in the MEDCC enhanced the desalination and chemical-production rates. The maximal desalination rate of 0.58 ± 0.02 mmol/h, which was 43% higher than that in the MEDCC, was achieved in the four-desalination-chamber MEDCC with the AEM-CEM stack structure and the membrane spacing of 1.5mm. The maximal acid- and alkali-production rates of 0.079 ± 0.006 and 0.13 ± 0.02 mmol/h, which were 46% and 8% higher than that in the MEDCC, respectively, were achieved in the two-desalination-chamber MEDCC with the BPM-AEM-CEM stack structure and the membrane spacing of 3mm.

Microwave-assisted alkali pre-treatment of wheat straw and its enzymatic hydrolysis were investigated and compared with the conventional alkali pre-treatment process. First, the effect of microwave power and pre-treatment time on the weight loss and composition of wheat straw was examined. The results show that the higher microwave power with shorter pre-treatment time and the lower microwave power with longer pre-treatment time had the same effect on the weight loss and composition at the same energy consumption. The comparison was then made between the effect of the microwave-assisted alkali pre-treatment and the conventional alkali one on the weight loss and composition of wheat straw. The wheat straw had a weight loss of 48·4% and a composition of cellulose 79·6%, lignin 5·7% and hemicellulose 7·8% after 25 min microwave-assisted alkali pre-treatment at 700 W, compared with a weight loss of 44·7% and a composition of cellulose 73·5%, lignin 7·2% and hemicellulose 11·2% after 60 min conventional alkali pre-treatment. The microwave-assisted alkali pre-treatment removed more lignin and hemicellulose from wheat straw with shorter pre-treatment time compared with the conventional alkali one. Finally, the enzymatic hydrolysis of pre-treated wheat straw (substrate concentration 50 g l−1, enzyme loading 20 mg g−1 substrate) was also investigated and the results indicate that the microwave-assisted alkali pre-treated wheat straw had higher hydrolysis rate, reducing sugar concentration and glucose content in the hydrolysate than the conventional alkali pre-treated one. Microwave-assisted alkali pre-treatment is a potential alternative of wheat straw pre-treatment for its enzymatic hydrolysis.

Lower Mekong Basin (LMB) experiences a recurrent drought phenomenon. However, few studies have focused on drought monitoring in this region due to lack of ground observations. The newly released Climate Hazards Group Infrared Precipitation with Station data (CHIRPS) with a long-term record and high resolution has a great potential for drought monitoring. Based on the assessment of CHIRPS for capturing precipitation and monitoring drought, this study aims to evaluate the drought condition in LMB by using satellite-based CHIRPS from January 1981 to July 2016. The Standardized Precipitation Index (SPI) at various time scales (1–12-month) is computed to identify and describe drought events. Results suggest that CHIRPS can properly capture the drought characteristics at various time scales with the best performance at three-month time scale. Based on high-resolution long-term CHIRPS, it is found that LMB experienced four severe droughts during the last three decades with the longest one in 1991–1994 for 38 months and the driest one in 2015–2016 with drought affected area up to 75.6%. Droughts tend to occur over the north and south part of LMB with higher frequency, and Mekong Delta seems to experience more long-term and extreme drought events. Severe droughts have significant impacts on vegetation condition.

In the water-rich karst regions, high water and mud outbursts are common geological disasters in tunnel construction. To ensure the safe and smooth construction of tunnel projects, it is necessary to consider anti-water pressure, water inrush prevention and geological disasters during the design of tunnels. Based on the Yongfutun Tunnel Project, this paper studies the application and effect of radial grouting and curtain grouting, which involves those in high-water-pressure tunnels under double-layer support conditions. To obtain the effects and parameters of radial grouting and curtain grouting, the influences of different grouting ranges on the tunnel’s surrounding rocks and supporting structures were analyzed and the finite difference method was adopted. The results show that the radial grouting of the surrounding rock can notably improve the initial support of the tunnel, but the impact is less obvious when the grouting range exceeds 4 m. The design of radial grouting is recommended to be 4.0 m to 4.5 m. Curtain grouting can effectively reduce the external water pressure of the tunnel lining. The external water pressure of the grouting area is 23% greater than that without curtain grouting. Curtain grouting can slow down the infiltration of external water pressure. This is beneficial to the stress of the tunnel lining structure, but the improvement in initial support force is slight. Moreover, curtain grouting improves the safety reserve of the secondary lining by strengthening the self-stability ability of the surrounding rock. Meanwhile, the double-layer primary support can effectively share the external water pressure and surrounding rock pressure. This study provides a certain reference for the lining design of high-water-pressure tunnels.

Abstract Transportation de-carbonization is a complex problem involving the economy, population, technology and environment. Implementing the pathway simulation based on systematic methods will help to optimize the transportation sustainability plan. This study’s key motivation is that earlier research ignored the relationship between driving factors and the transmission process. To quantitatively identify the path and process of emission reduction, a hybrid system dynamics STIRPAT-SD model is proposed to explore the transportation optimization’s de-carbonization ability. This study fully considers the composition of elements and subsystems based on the STIRPAT theoretical model and visually shows the system’s feedback relationship. Transportation structural and technical optimization scenarios are set to identify the threshold reduction paths. It is found these optimization strategies have significant de-carbonization effects. And transportation structure policy has the highest de-carbonization efficiency, the emission intensity decreased by 9.1% under the TSS2 scenario (Transportation structure scenario). This study proposes a novelty model combining dynamic simulating processes with a significantly theoretical model to improve simulation and factor composition accuracy. And the joint scenario setting identifies the most effective de-carbonization pathway and clarifies the threshold of all possible pathways. Research findings can effectively track, test, predict the achievement of policy goals, and provide policy optimization references for the sustainable development related to the transportation system in practice.

As a relatively mature technology, biomass molded fuel (BMF) is widely used in distributed and centralized heating in China and has received considerable government attention. Although many BFM incentive policies have been developed, decreased domestic traditional fuel prices in China have caused BMF to lose its economic viability and new policy recommendations are needed to stimulate this industry. The present study built a regionalized net present value (NPV) model based on real production process simulation to test the impacts of each policy factor. The calculations showed that BMF production costs vary remarkably between regions, with the cost of agricultural briquette fuel (ABF) ranging from 86 US dollar per metric ton (USD/t) to 110 (USD/t), while that of woody pellet fuel (WPF) varies from 122 USD/t to 154 USD/t. The largest part of BMF’s cost composition is feedstock, which accounts for up 50%–60% of the total; accordingly a feedstock subsidy is the most effective policy factor, but in consideration of policy implementation, it would be better to use a production subsidy. For ABF, the optimal product subsidy varies from 26 USD/t to 57 USD/t among different regions of China, while for WPF, the range is 36 USD/t to 75 USD/t. Based on the data, a regional BMF development strategy is also proposed in this study.

An energy-saving ethanol fermentation technology was developed using uncooked fresh sweet potato as raw material. A mutant strain of Aspergillus niger isolated from mildewed sweet potato was used to produce abundant raw starch saccharification enzymes for treating uncooked sweet potato storage roots. The viscosity of the fermentation paste of uncooked sweet potato roots was lower than that of the cooked roots. The ethanol fermentation was carried out by Zymomonas mobilis, and 14.4 g of ethanol (87.2% of the theoretical yield) was produced from 100g of fresh sweet potato storage roots. Based on this method, an energy-saving, high efficient and environment-friendly technology can be developed for large-scale production of fuel ethanol from sweet potato roots.