• Energy Research
• Restricted close
• CA close
• CN close
• EU close
• Renewable Energy close

Hot water heat stores with stratification are a common technology used in solar energy systems and reuse of waste heat. Adding a PCM module at the top of the water tank would give the system higher storage density, and compensate heat loss in the top layer. The work presented here includes experimental results and numerical simulation of the system using an explicit finite-difference method. Experiments and simulations were carried out using different cylindrical PCM modules. With only 1/16 of the volume of the store being PCM, 3/16 of water at the top of the store was held warm for 50% to 200% longer and the average energy density was increased by 20% to 45%. Furthermore, these 3/16 of water were reheated by the heat from the module after being cooled down in only 20 min.

Abstract An exergy analysis, which only considers the unavoidable exergy destruction, is conducted for single, double, triple and half effect Water–Lithium bromide absorption cycles. Thus, the obtained performances represent the maximum achievable performance under the given operation conditions. The coefficient of performance (COP), the exergetic efficiencies and the exergy destruction rates are determined and the effect of the heat source temperature is evaluated. As expected, the COP increases significantly from double lift to triple effect cycles. The exergetic efficiency varies less among the different configurations. In all cycles the effect of the heat source temperature on the exergy destruction rates is similar for the same type of components, while the quantitative contributions depend on cycle type and flow configuration. Largest exergy destruction occurs in the absorbers and generators, especially at higher heat source temperatures.

In this work, a novel enhanced deep borehole heat exchanger (EDBHE) was proposed to improve heat extraction efficiency based on the jet grouting method. By means of this technology, a soilcrete zone with high thermal conductivity was built near the wellbore. To analyze the feasibility and efficiency of this method, we firstly constructed a validated deep borehole heat exchanger (DBHE) model based on the field experimental data. Numerical simulations were carried out to investigate the 30-year production performance of EDBHE. Results demonstrated that the jet grouting method is an efficient way for improving thermal output of DBHE. It is evaluated that the average annual heat production rate over a 30-year heating period of EDBHE is 463.2 kW, which is 1.27 times as that of DBHE. Sensitivity analyses indicate that the heat production rate and outlet temperature mainly depend on the height and radius of the artificial soilcrete zone. However, thermal output is not sensitive to thermal conductivity of the soilcrete zone due to the higher thermal resistance of the geological formation. For the experimental site used in this work, the recommended height, radius, and thermal conductivity of the soilcrete are 1000 m, 1.0 m, and 50 W/m °C, respectively.

Increasing levels of wind energy in modern electrical power system is initiating a need for accurate analysis and estimation of transient stability of wind turbine generation systems. This paper investigates the transient behaviors and possible direct methods for transient stability evaluation of a grid-connected wind turbine with squirrel cage induction generator (SCIG). Firstly, by using an equivalent lump mass method, a three-mass wind turbine equivalent model is proposed considering both the blades and the shaft flexibility of the wind turbine drive train system. Combined with the detailed electromagnetic transient models of a SCIG, the transient behaviors of the wind turbine generation system during a three-phase fault are simulated and compared with the traditional models. Secondly, in order to quickly estimate the transient stability limit of the wind turbine generation system, a direct method based on normal form theory is proposed. The transient models of the wind turbine generation system including the flexible drive train model are derived based on the direct transient stability estimation method. A method of critical clearing time (CCT) calculation is developed for the transient stability estimation of the wind turbine generation system. Finally, the CCT at various initial mechanical torques for different dynamical models are calculated and compared with the trial and error method by simulation, when the SCIG stator terminal is subjected to a three-phase short-circuit fault. The results have shown the proposed method and models are correct and valid.

This paper describes a method that was applied as a part of the creation of a wind map for the Czech Republic. The method (abbreviated VAS/WindAtlas) combines an interpolation method (VAS) with the Wind Atlas methodology applied by using the microscale model WAsP. While WAsP eliminates the site-specific effects around measurement sites to provide generalised wind conditions (GWC), VAS interpolates the GWC over the entire domain and takes into account the general increase of wind speed with altitude. As a result, an altitude-dependent generalised wind map is provided. Then, a final high-resolution calculation is performed by WAsP. The VAS/WindAtlas method is considerably more simplified and less computationally demanding than approaches employing more complex numerical models, but it requires a sufficiently dense network of wind measurements, a thorough data quality evaluation and careful corrections that compensate for the known limitations of the applied data and methods. A comparison of the original wind map with new independent wind measurements, which were obtained after the wind map calculation, was performed with a detailed analysis of the expected errors and uncertainties at the validation sites. The presented VAS/WindAtlas method proved to be good solution to estimate wind resources of Czech Republic.

Olive pomace is an interesting agro-industrial byproduct that can be a potential raw material for densified biomass products. At first, 2-phase (2 PH) and 3-phase (3 PH) olive pomace pellets were analyzed in order to evaluate their quality in terms of the main parameters required by the European Standard EN 17225-6. The characterization of the pure pellets has shown important problems because of out of limits values of nitrogen, durability and copper in the two olive pomace. To improve the properties of olive pomace pellets, the possibility of manufacturing pellets by mixing olive pomace and olive tree pruning (PR) was investigated. Several blends at different weight ratios were analyzed in order to verify the effect of mixing on the pellet properties. It can be concluded that the physical properties of all mixtures are in compliance with the requirements of the standard. In particular, two best blends in terms of physical, chemical and mechanical characteristics were identified as becoming potential fuel for combustion and gasification applications: 75PR252 PH (75% pruning and 25% 2-phase pomace) and 50PR503 PH (50% pruning and 50% 3-phase pomace).

In 2008, following its R&D strategy roadmap for Concentrated Solar Power, Abengoa designed, built and tested a unique Molten Salts pilot plant at the representative scale of 8 MWhth, coupled with a trough oil loop. The objectives of this project were based on evaluating the technology at a scale at which the results are sufficiently representative of the real circumstances facing a commercial plant that utilizes this storage technology. To this end, the MS-TES plant was brought into operation on January 19th, 2009, been the first demo plant of indirect double tank storage in operation in the world. Key points such a material corrosion, analysis of possible leakage points, calculation of performance or true efficiency of the storage (including a thorough assessment of thermal losses) and analysis of plant operation are the lines that have been analysed at this plant. Operational aspects such as the mechanical assembling, the pre-heating, the filling up and plant performance were deeply addressed. Key components as the storage tanks, the heat exchanger, the molten salts pumps, the heat-tracing systems or valves and instrumentation were tested. In this first paper, the description and commissioning of the plant is presented together a set of lessons learnt to be applied at the commercial plant scale.

The metropolitan cities of developed countries comprise more than 50% of the global population and consume over 60% of the world's energy. Many governments plan to enhance their energy infrastructure and the electricity supply–demand reliability of their energy sources. Among them, South Korea's government has developed electricity generation facilities, most of which use renewable resources such as photovoltaic and wind energy. This study determines the optimal renewable electricity generation configuration for one of the largest metropolitan cities in South Korea, Busan metropolitan city. A simulation using 2013 Busan electricity demand data produces this optimal configuration, which includes photovoltaic panels, wind facilities, converters, and batteries with $0.399 of COE (Cost of Electricity) and 100% of renewable fractions. Both the study's practical limitations and implications are discussed.