• Energy Research
• CN close
• DE close
• TH close
• Energies close

A new non-pillar mining technology, gob-side entry retaining by roof cutting (GERRC), different from the conventional gob-side entry retaining formed by a roadside filling support, is introduced in this study. In the new technology, roof cutting is conducted so that the roof plate forms a short cantilever beam structure within a certain range above the retained entry, thus changing the stress boundary condition of the roof structure. To explore the deformation characteristics of the roof under this special condition, a short cantilever beam mechanical model was established and solved using energy theory and displacement variational methods. Meanwhile, a theoretical and analytical control solution for roof deformation was obtained and verified via field-measured results. Based on the aforementioned calculation, the relationship between the roof deformation and main influence parameters was explored. It was concluded that the rotation of the upper main roof and width of the retained entry had the most significant impacts on roof deformation. Bolt and cable support and temporary support in the entry had a non-obvious influence on the roof deformation and could not prevent the given deformation that was caused by the rotation of the upper main roof. Based on comprehensive theoretical analysis and calculation results, ideas and countermeasures to control short cantilever roof deformation—that is, designing a reasonable height of roof cutting and a controlled width of retaining entry—were proposed and tested. Field monitoring shows that the entry control effects were satisfactory.

The greenhouse’s energy consumption is a major limiting factor for output and development. To address this, it is necessary to adopt green and low-carbon heating technologies to replace traditional fuels. This will not only help conserve energy but will also reduce emissions, thereby improving the thermal environmental conditions for agriculture. This paper aims to research and develop a vertical heat exchange tube array device specifically designed for greenhouses. The focus is on enhancing the passive heat absorption and heat storage efficiency of the device and its influence on the thermal environment of the greenhouse. In order to improve the heat absorption and storage efficiency of the heat exchanger device and its impact on the greenhouse thermal environment, experimental comparative analysis was conducted using air, water, and phase-change materials as working fluids inside the pipes. Through a combination of experiments and simulations, it was verified that the heat exchanger device is capable of actively regulating the greenhouse thermal environment. The results show that heat exchangers of all three types of working fluids can effectively improve the stability of soil temperature and play a “shifting the peak and filling the valley” role in regulating the indoor air temperature while positively regulating the relative humidity of the air. Notably, when the working fluid is a phase-change material, it has the most significant impact on the thermal environment of the greenhouse.

Hydraulic fracturing is the main means for developing low-permeability shale reservoirs. Whether to produce artificial fractures with sufficient conductivity is an important criterion for hydraulic fracturing evaluation. The presence of clay and organic matter in the shale gives the shale creep, which makes the shale reservoir deform with time and reduces the conductivity of the fracture. In the past, the influence of shale creep was ignored in the study of artificial fracture conductivity, or the viscoelastic model was used to predict the conductivity, which represents an inaccuracy compared to the actual situation. Based on the classical Perzyna viscoplastic model, the elasto-viscoplastic constitutive model was obtained by introducing isotropic hardening, and the model parameters were obtained by fitting the triaxial compression creep experimental data under different differential stresses. Then, the constitutive model was programmed in a software platform using the return mapping algorithm, and the model was verified through the numerical simulation of the triaxial creep experiment. Then, the creep calculation results of the viscoplastic constitutive model and the power law model were compared. Finally, the viscoplastic constitutive model was applied to the simulation of the long-term conductivity of the fracture to study the influence of creep on the fracture width, and sensitivity analysis of the influencing factors of the fracture width was carried out. The results show that the numerical calculation results of the viscoplastic model were in agreement with the experimental data. The decrease in fracture width caused by pore pressure dissipation and reservoir creep after 72 h accounts for 32.07% of the total fracture width decrease.

T oilfield is the fractured-vuggy carbonate reservoir at a temperature of around 130 °C, with salinity of up to 22 × 104 mg/L. In order to solve the problem of the high water cut in the late development stage of T oilfield, we selected XN-T from 27 kinds of swelling retarding particles by testing their swelling capacity, and coated a thin film to improve its retarding swelling capacity. The mechanisms of strong water absorption and water-holding abilities of particles were analyzed by infrared spectrometry and SEM. In the core flow experiment, the plugging rate was found to be 98.42%. Finally, the injection parameters of the coated particles were optimized to maximize the water plugging and profile control ability, resulting in an optimal particle size of 0.4–0.6 mm and a mass fraction of 10%.

The application of voltage reduction in medium and low voltage grids to reduce peak power demand or energy consumption has been implemented since the 1980s using several approaches. Conservation Voltage Reduction (CVR), as one such approach, uses a voltage control device to reduce or increase the voltage setpoint on a busbar, thereby reducing or increasing the amount of active and reactive power supply in the network. Voltage regulation for CVR is always implemented according to established network planning standards in each country. Research in this field has proven that a CVR factor (CVRf) of 0.7–1.5 for peak demand reduction can be achieved. This is an evaluation metric of CVR. The aim of this research is to determine and validate CVRf for peak demand reduction by comparing actual results obtained during regular tap changes with other randomly distributed periods outside tap change operations, using a set of measurement data. It is important to understand CVR deployment capability by evaluating CVR potentials from historical random tap operations before a robust network-wide deployment is introduced. This research provides such guidance. It also provides a novel approach to determining tap changes from voltage measurements using a time-based algorithm. A CVRf ranging from 0.95 to 1.61 was estimated using a measurement dataset from a test field. The result of the entire evaluation shows that the CVRf are smaller during peak PV production and greater during peak demand periods. Further evaluation using statistical hypotheses testing and a control chart was used to validate the evaluation.

The tension legs are the essential parts of the tension legs platform-type (TLP-type) floating offshore wind turbine (FOWT) against the extra buoyancy of FOWT. Therefore, the TLP-type FOWT will face the risk of tension leg failure. However, there are seldom analyses on the hydrodynamic response and tension leg failure performance of FOWT with inclined tension legs. In this paper, a hydrodynamic model was established using three-dimensional hydrodynamic theory and applied in the motion response and tension analyses of FOWT with conventional and new tension leg arrangements on Moses. The influence of draft and tension leg arrangement on the performance of FOWT with inclined tension legs were studied. The optimum draft was the height of the column and lower tensions were obtained for the new tension leg arrangement. Moreover, the tension leg failure performance of FOWT with inclined tension legs was evaluated under different failure conditions. The results illustrated that the FOWT with the new tension leg arrangement can still operate safely after one tension leg fails.

Environmental pollution damages public health and affects economic development. Environmental regulation is the main way for the government to solve environmental pollution. So what type of environmental regulation works better for public health and economic development? Can environmental regulation have an influence on economic development through public health? To solve these problems, this research uses China’s provincial panel data from 2013 to 2017 to divide environmental regulation into command-control policy tools and economic incentive policy tools and uses the mediating effect model to examine the relationship among environmental regulation, public health and economic development. The results show that: (1) There is a positive correlation between economic incentive policy tools and economic development; while no significant relationship between command-control policy tools and economic development is founded; (2) The relationship between command-control policy tools and public health is not significant, while the relationship between economic incentive policy tools and public health is positive; (3) Public health does not play a mediating role between command-control policy tools and economic development but plays a partial mediating role between economic incentive policy tools and economic development. Therefore, the government should strengthen the use of economic incentive policy tools to promote public health and sustainable economic development.

A high-speed centrifugal pump is the key facility to deliver oil in an aero-engine. The stable operation is quite important to the safety of the engine. High-speed pump stability is essentially caused by the transient pressure pulsations excited by the complex flow within the pump, which needs to be clarified, especially for the pump under a rotating stall condition. In the current research, unsteady pressure pulsation and the corresponding flow distribution of the high-speed centrifugal pump are analyzed using the delayed detached-eddy simulation (DDES) method. Pressure signals within the pump are extracted by monitoring points. Results show that the dominant components in the pressure spectrum exhibit a significant difference at various flow rates, which locates at the blade passing frequency fBPF under the rated working condition and deviates to five times the shaft frequency (5fn) at the stalled condition. Such phenomenon is not observed in the normal centrifugal pump with low speed when using numerical and experiment methods, and usually the amplitude at fBPF reaches the maximum. Under the stalled condition, the component at 0.2fn is generated and considered as the rotating stall frequency, which is the same at different stalled flow rates. From velocity distribution, it is found that several blade channels are stalled as characterized by the large-scale separation bubbles, which are induced and triggered by the volute tongue.