• Energy Research
• physical sciences close
• CN close
• NL close

Characteristics of Tm:YAG ceramic for high efficient 2-μm lasers are analyzed. Efficient diode end-pumped continuous-wave and Q-switched Tm:YAG ceramic lasers are demonstrated. At the absorbed pump power of 53.2W, the maximum continuous wave (cw) output power of 17.2 W around 2016 nm was obtained with the output transmission of 5%. The optical conversion efficiency is 32.3%, corresponding to a slope efficiency of 36.5%. For Q-switched operation, the shortest width of 69 ns was achieved with the pulse repetition frequency of 500 Hz and single pulse energy of 20.4 mJ, which indicates excellent energy storage capability of the Tm:YAG ceramic.

Abstract An alkaline earth boro-aluminosilicate glass (Eagle XG), a soda-lime glass, and a light-weight polyethylene-terephthalate (PET) foil, used as typical substrates for photovoltaics, were treated by an energetic proton beam (3 MeV, dose 106–107 Gy) corresponding to approx. 30 years of operation at low Earth orbit. Properties of the irradiated substrates were characterized by atomic force microscopy, optical absorption, optical diffuse reflectance, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and terahertz (THz) spectroscopy. Minimal changes of optical and morphological properties are detected on the bare Eagle XG glass, whereas the bare PET foil exhibits pronounced increase in optical absorption, generation of photoluminescence, as well as mechanical bending. On the other hand, the identical substrates coated with Indium-tin-oxide (ITO), which is a typical material for transparent electrodes in photovoltaics, exhibit significantly higher resistance to the modifications by protons while ITO structural and electronic properties remain unchanged. The experimental results are discussed considering a potential application of these materials for missions in space.

Abstract The molten droplet fragmentation dominated by hydrodynamic mechanisms is the key process at the stage of pressure propagation in the process of the fuel–coolant interaction (FCI) which may occur during the course of a severe accident in a light water reactor (LWR). However, due to complication of the process, hydrodynamic fragmentation cannot be described by a particular mechanism, and there is no sufficient experimental studies under high pressure shock condition for this kind of fragmentation evaluation. In this paper, a multi-phase thermal hydraulic code with the Volume of Fluid Method (VOF) is developed, Continuum surface force (CSF) model is employed to compute the surface tension. The breakup process of a molten droplet under sudden accelerations is numerically analyzed to investigate the mechanism of fragmentation in vapor explosion. The results show that the breakup process experiences two stages: deformation and disintegration, which agrees with the simulation by Duan et al. (2003) using Moving Particle Semi-implicit (MPS) method. It is found that an increase in intensity of pressure pulse will accelerate the completion of breakup process and the dimensionless breakup time from the simulation is not strongly affected by Bond number ( Bo ). The simulation results suggest that the deformation imposed by the external hydrodynamic pressure distribution should be the dominant factor in breakup process for molten droplets in liquid–liquid system simulated in this paper.

Safety and Security Science

Abstract In this work, we propose an acoustic energy harvesting metamaterial consisting of an array of silicone rubber pillars and a PZT patch deposited on an ultrathin aluminum plate with several holes based on locally resonant mechanism. The resonance is formed by removing four pillars, drilling a few of holes and attaching the PZT patch on the aluminum plate. The strain energy originating from an incident acoustic wave is centralized in the resonant region, and the PZT patch is used to convert the elastic strain energy into electrical power. Numerical analysis and experimental results show that the proposed millimeter-scale harvester with holes obviously improves the effect of acoustic energy harvesting while performing at the subwavelength scale for sonic low-frequency environment (less than 1150 Hz). In addition, the experimental results demonstrate that the maximum output voltage and power of the proposed acoustic energy harvesting system with 16 holes of 2 mm radius are 3 and 10 times higher than those without holes at the resonant mode for 2 Pa of incident acoustic pressure. Both the number and size of holes have a significant effect on the performance of acoustic energy harvesting. The advantages of the proposed structure are easy-to-machine and full of practicality, and it can be used in broad applications for low-frequency acoustic energy harvesting.

AbstractNiNb2O6‐BaTiO3 ceramics were prepared using a solid‐state reaction method, and the effects of the addition of NiNb2O6 on the dielectric properties and energy‐storage characteristics of BaTiO3 were investigated systematically. We used XRD to show that the obtained NiNb2O6‐BaTiO3 ceramics possess a single perovskite structure. The addition of NiNb2O6 improves the energy density efficiency and leads to a decrease of the dielectric loss to less than 1 %. Moreover, optimum performances of the BaTiO3 ceramics can be achieved by the addition of 1.0 mol % NiNb2O6, at which content the obtained ceramic satisfies the X7R specification. The addition of NiNb2O6 stabilizes the crystalline lattice, which enhances the temperature stability of the dielectric properties accordingly.

Acoustic resonances in combustion systems like central heating boilers prohibit further technological advances in these systems. The design and construction is obstructed by acoustic problems because they are largely misunderstood, in spite of our increase in knowledge over the last decades. The flame often acts as an active element in the acoustic field, because the flame transfer function of acoustic waves has a large amplitude at low frequencies. Current models of the phase of the flame transfer function of Bunsen-type flames, based on kinematic behavior of the flame dynamics, completely miss the experimentally observed phase, unless the measured flow field is used in the model. In the current paper we analyze numerical results of the flame dynamics, flow field and flame transfer function found with a 2D detailed numerical model of the flow and structure of the flame on a multiple-slit burner. The model is validated with experiments of the flame dynamics (using chemiluminescence), flow dynamics (using PIV) and flame transfer function (using OH luminescence for the heat release fluctuations and heated wire probe for the acoustic distortions) on exactly the same configuration. A very good agreement is found which indicates the importance of predicting all the influences of the flow on the flame and vise-versa.