• Energy Research
• Restricted close
• other engineering and technologies close
• US close
• CN close
• CA close

Abstract The kinetics of methane hydrate decomposition was studied using a semibatch stirred-tank reactor. The decomposition was accomplished by reducing the pressure on a hydrate slurry in water to a value below the three-phase equilibrium pressure at the reactor temperature. The data were obtained at temperatures from 274 to 283 K and pressures from 0.17 to 6.97 MPa. The stirring rates were high enough to eliminate mass-transfer effects. Analysis of the data indicated that the decomposition rate was proportional to the particle surface area and to the difference in the fugacity of methane at the equilibrium pressure and the decomposition pressure. The proportionality constant showed an Arrhenius temperature dependence. An estimate of the hydrate particle diameters in the experiments permitted the development of an intrinsic model for the kinetics of hydrate decomposition.

Abstract Thermal energy storage (TES) systems are growing to a relevant role in solar cooling applications. Hence, high energy density is a desirable property of the TES system. Phase change materials (PCM) helps to increase this characteristic. A high temperature pilot plant able to test different types of TES systems and materials was designed and built at the University of Lleida (Spain). This pilot plant is composed mainly of three parts: heating system, cooling system, and different storage tanks. Two identical storage tanks based on the shell-and-tubes heat exchanger, one of them including 196 squared fins in the bundle of the tubes and the other without, were experimentally tested. Hydroquinone was selected as the storage material, having a latent heat of 205 kJ/kg and a phase change temperature between 168 and 173 °C. The aim of this paper is to test experimentally, and compare the average effectiveness of the TES systems analyzed using PCM for solar cooling and refrigeration applications. It was found out that for the same tank configurations (shell-and-tubes) even changing drastically the dimensions of the tank or the number and the diameter of the tubes, the average effectiveness curve proposed in the literature fits well with the results showed here.

<div class="section abstract"><div class="htmlview paragraph">The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO₂-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO₂-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.</div><div class="htmlview paragraph">In this framework, a comprehensive approach covering the whole powertrain is of primary importance in order to simultaneously meet the performance, efficiency, noise and emission targets, and therefore, further development of the combustion system design and injection system represent important levers for additional improvements. For this purpose, a dedicated 0.5 dm³ single-cylinder engine has been developed and equipped with, a state-of-the-art Euro 6 combustion system, and an advanced common rail fuel injection system (FIS) offering higher flexibility in terms of injection strategy and higher quantity accuracy. Three injector nozzles with different hydraulic flow rates (HF) have been selected and employed for the overall combustion process optimization.</div><div class="htmlview paragraph">The optimization has been performed by means of an extensive DoE-based test campaign in which the engine and FIS operating parameters have been parametrized with the aim to carry out a proper combination in terms of HF and injection strategy. The results at partial load conditions evidence significant advantages in applying an advanced injection pattern, while the HF reduction can significantly improve the smoke emission and combustion noise without fuel consumption penalties. Therefore, a proper combination and optimization of the HF and injection strategy can provide low noise and engine-out smoke while maintaining the rated power performance targets.</div></div>

The aim of the paper is to study the influence of the power transformer on signal transmission in the case of a power line communication (PLC) system in a overhead Medium Voltage (MV) power network. A model of the PLC system was carried out by means of the Simulink® software. A distributed parameter MV overhead line, two power transformers, the signal coupling interface of a ST7540 FSK powerline transceiver were included in the model. The performances of the complete PLC communication system are evaluated for different line lengths by means of the attenuation computed as ratio between the received and transmitted voltage signals. © 2011 IEEE.

Artículos en revistas Numerical models of transmission-constrained electricity markets are used to inform regulatory decisions. How robust are their results? Three research groups used the same data set for the northwest Europe power market as input for their models. Under competitive conditions, the results coincide, but in the Cournot case, the predicted prices differed significantly. The Cournot equilibria are highly sensitive to assumptions about market design (whether timing of generation and transmission decisions is sequential or integrated) and expectations of generators regarding how their decisions affect transmission prices and fringe generation. These sensitivities are qualitatively similar to those predicted by a simple two-node model. info:eu-repo/semantics/publishedVersion

Abstract Both steady-state AC and DC power flow models are commonly used for techno-economic studies of power systems. The DC-based approach limits the computational burden by assuming small-angle approximation, ignoring power losses, reactive power flows, and voltage variations. It, therefore, matters to understand if this approach affects system vulnerability, reliability, and contingency assessments. To this aim, we use the time-sequential Monte Carlo simulation and an N-k′-1 scenario for reliability and contingency analyses, respectively. Further, we introduce a new index for vulnerability assessment. The IEEE reliability test system (RTS) and the modified RTS are modeled. The results show that the DC model underestimates the reliability indices by about 20% and more than 90% in a stressed network. We also show a small error of 5%, owing to the assumptions of the DC model, which can lead to inaccurate simulations concerning the cascading failures. Finally, the sources of the inaccuracy in the DC-based model are investigated. The results prove that AC power flow model should be privileged for the line capacity-based assessments.

The recommended power quality (PQ) indices in electric power systems are defined based on the discrete Fourier transform (DFT). DFT is mostly evaluated applying fast Fourier transform (FFT) algorithm which requires signals to be periodic in nature. Hence, it evaluates PQ indices accurately for stationary PQ disturbances only. However, in case of nonstationary PQ disturbances signal is aperiodic and FFT results in erroneous assessment due to spectral leakage phenomena. Furthermore, FFT cannot provide time information of the PQ indices as computation is performed in frequency domain only. Which is significant shortcoming of the FFT when dealing with time-varying PQ disturbances to extract dynamic signature of the signal. Thereby, this paper presents a framework of redefining PQ indices for stationary and nonstationary PQ disturbances employing time-frequency distribution (TFD) method. Among all TFDs, reduced interference distribution (RID) represents the most suitable properties for analyzing time-varying PQ disturbances. Hence, in this work, it is employed to reformulate PQ indices typically used in electric power systems. The results of two synthetic examples considering stationary and nonstationary PQ disturbances imply that the RID-based redefined PQ indices are closer to the actual values. Also, they provide more accurate results than the existing transient PQ indices and traditional FFT-based method.

Electric vehicles (EVs) are considered a substitute for fossil-fueled vehicles due to rising fossil fuel prices and accompanying environmental concerns, and their use is predicted to increase dramatically shortly. However, the widespread use of EVs and their large-scale integration into the energy system will present several operational and technological hurdles. In the energy industry, an innovative solution known as the EVs smart parking lot (SPL) is introduced to handle EV charging and discharging electricity and energy supply challenges. This paper investigates social equity access and mobile charging stations (MCSs) for EVs, where the owner of MCSs is the EV parking lot. Accordingly, a new self-scheduling model for SPLs is presented in this paper that incorporates scheduling of the MCSs as temporary charging infrastructures while considering social equity access and optimizes SPL energy generation and storage schedule. The main objectives of this research are to (i) develop MCSs accessibility measures and quantify the equity impacts of MCSs locations by modeling prioritized demand based on several indices; (ii) determine the optimal set-points of SPL components (i.e., combined heat and power (CHP), photovoltaic system, electrical and heat-energy storage, and MCSs) to manage electrical peak demand and to maximize the economic benefits of SPLs. Results indicate that the proposed demand prioritization function model can meet the required EV charging demands for prioritized events, and the self-scheduling model for SPLs satisfies the charging demand of the EVs in the SPL location. Also, the social equity access to the EV charging stations is satisfied by analyzing the operation of MCSs around the prioritized demand of the prioritized events and social equity access indices.