• Energy Research
• 7. Clean energy close
• CN close
• US close
• GB close
• DE close
• FR close

The use of hydrogen gas as a means of decoupling supply from demand is crucial for the transition to carbon-neutral energy sources and a greener, more distributed energy landscape. This work shows how simple commercially available titanium nitride coatings can be used to extend the lifetime of 316 grade stainless-steel electrodes for use as the cathode in an alkaline electrolysis cell. The material was subjected to accelerated ageing, with the specific aim of assessing the coating’s suitability for use with intermittent renewable energy sources. Over 2000 cycles lasting 5.5 days, an electrolytic cell featuring the coating outperformed a control cell by 250 mV, and a reduction of overpotential at the cathode of 400 mV was observed. This work also confirms that the coating is solely suitable for cathodic use and presents an analysis of the surface changes that occur if it is used anodically.

Abstract A biomass oil/diesel blend was prepared using an emulsion method and combusted in a diesel engine. An injector was then removed and the morphology, composition, and structure of the carbonaceous deposits on the pintle-type nozzle were characterized using a combination of HRTEM, SEM/EDAX, Raman and XRD. Results showed that the carbon deposition of the emulsified fuel with high crystallinity was greater than that of diesel. The agglomerated particulate diameters of the deposited carbon from diesel and emulsified fuel were approximately 10–30 μm and 50 μm, respectively. The carbon deposition mechanism from the emulsified fuel was attributed to the high oxygen content of the groups leading to increased polymerization and subsequent condensation on the nozzle surfaces that was then carbonised.

The main problem involved in utilization of solar energy is low efficiency of photovoltaic conversion and high cost. The objectives of the paper are to increase the efficiency of photovoltaic cells and to reduce the cost of the photovoltaic module. A novel method is presented in this paper to increase the efficiency of photovoltaic modules and reduce the cost by the use of specially designed solar concentrators. The efficiency of photovoltaic module is increased by covering an angle of nearly 180° so that the sun's radiation converges through out the day from all angles on to a fixed flat plate module. The cost is reduced by use of cheaper glass for module and covering a wider area for the radiation. The above objectives are achieved by the use of a special arrangement of three lenses for the concentrators.

Sustainability of agro-food supply chains has recently become the subject of greater interest from consumers, firms, governmental organizations and academia as the environment continues to deteriorate. One of the most critical factors influencing the sustainability of an agro-food supply chain is its network design. A particularly challenging aspect in this context is the broad range of influencing indicators associated with the Triple Bottom Line (TBL) of sustainability that need to be considered. However, many of these indicators could not be fully integrated or measured by single-step optimization problems. This paper presents a critical literature review of operational research methods for the design of sustainable supply chains. A novel two-stage hybrid solution methodology is proposed. In the first stage, a partner selection is performed using a hybrid multi criteria decision making based on Analytic Hierarchy Process (AHP) method and the Ordered Weighted Averaging (OWA) aggregation method. The result obtained in the first stage is used in the second stage to develop a multi-objective mathematical model to optimize the design of the supply chain network. This approach allows the simultaneous consideration of all three dimensions of sustainability including carbon footprint, water footprint, number of jobs created and the total cost of the supply chain design. The proposed approach generates a Pareto frontier to aid users in making decisions. Numerical experiments are completed utilizing data from an agro-food company to demonstrate the efficiency and effectiveness of the proposed solution methodology. The analyzes of the numerical results provide important organizational, practical and policy insights on (1) the impact of financial and environmental sustainability on supply chain network design (2) the tradeoff analysis between environmental emission, water footprint, societal implications and associated cost for making informed decision on supply chain investment.

Cu2CdSn(S,Se)(4) is an important candidate material for thin film solar cell absorber layers. In this work, low-cost Cu2CdSnS4 nanocrytal thin film with a stannite structure has been successfully fabricated by a butyldithiocarbamate-based ethanol solution approach. The selenized Cu2CdSn(S,Se)(4) thin film shows large densely packed grains and has a suitable band gap value of 1.01 eV. The Cu2CdSn(S,Se)(4) thin film solar cell with a proof-of-concept power conversion efficiency of 3.1% was fabricated. (C) 2014 Elsevier B.V. All rights reserved.

Since the invention of fluorescent light sources, there is strong interest in Eu3+ activated phosphors as they are able to provide a high color rendering index (CRI) and luminous efficacy, which will also hold for phosphor converted light emitting diodes. Due to an efficient U6+ to Eu3+ energy transfer in Gd3Li3Te2O12:U6+,Eu3+, this inorganic composition shows red photoluminescence peaking at 611 nm. That means Eu3+ photoluminescence can be nicely sensitized via excitation into the U6+ excitation bands. Therefore, photoluminescence properties, such as temperature dependent emission and emission lifetime measurements, are presented. Charge transfer bands were investigated in detail. Additionally, density functional theory calculations reveal the band structure of the pure, i.e., non-doped host material. Obtained theoretical results were evaluated experimentally by the aid of diffuse UV reflectance spectroscopy.

Abstract The rapid increase in energy demand and the limited resources of fossil fuel as well as the environmentally damaging effects, drive the world to find new options for sustainable electricity generation, which is represented by renewable energies. Concentrating solar power (CSP) is one of the most promising technologies in the field of electricity generation to tackle this issue with a competitive cost in the future. This paper presents an investigation of the potential of implementation of CSP plants in Libya. The socio-economic context, current energy situation of the country and different types of CSP plants are discussed. Moreover, an assessment of site parameters required for CSP plants including solar resources, land use and topography, water resources and grid connections are investigated in detail. In addition, thermo-economic simulation of a 50 MW parabolic trough power plant is performed. The simulation is conducted based on meteorological data measured by the weather station installed at the Centre for Solar Energy Research and Studies (CSERS) in Tajoura city. The performance results are compared with the reference plant Andasol-1 in Spain. Even though the proposed plant is located on the North coast where solar resources are at their minimum compared with other regions of the country, the outcome of the study proves that Libya is not only suitable but it can be economically competitive in the implementation of CSP technology.

Abstract The convergence characteristics of two Monte Carlo models are investigated in this paper. These two models or their variations have been used by the electric power industry. Model 1 is based on the random sampling of generator and transmission line status for each hour. Model 2 advances the generation and transmission using the next-event approach. Mathematical analysis and system studies indicate that model 2 converges slower than model 1. The simulation time for model 2 is generally more than twice the mean duration of loss of load. The CPU time per year of simulation is shorter for model 2. However, the total CPU time for model 2 is much longer than for model 1.