• Energy Research
• engineering and technology close
• 7. Clean energy close
• 13. Climate action close
• 6. Clean water close
• MX close
• CO close

The present paper develops a methodology to choose the best connection scheme for traction substations of a Massive Electrical Railway System (MERS) and distribution substations in urban areas using graph theory and economical optimization.

Radiative heat transfer in a 1 kW cavity-type solar reactor devoted to the thermal reduction of compressed ZnO and SnO2 powders is analyzed by a Monte Carlo ray tracing simulation. The developed model takes into account the radiative properties of the reactant particles and of the ceramic cavity walls, as well as the angular intensity distribution of the incoming concentrated solar irradiation. The model also includes the conduction heat losses through the lateral walls and the energy consumed by the endothermic chemical reaction. It is used to predict the temperature and the absorbed flux density profiles on the inner cavity walls for different main features of the reactor, concerning the dimensions of the cavity and the type of reactant. Results show that the absorbed flux density profile and the theoretical thermochemical efficiency change with the cavity aspect ratio and with the oxide reactant. The cavity with an aspect ratio of 3 and a SnO2 pellet undergoing dissociation presents the highest thermochemical efficiency. Additionally, a different configuration of the reactor design is considered, which consists in implementing a layer of reactive particles on the inner lateral cavity wall. The model highlights that this type of reactor operation with a reactant layer on the lateral cavity wall results in an improved thermochemical efficiency.

Abstract Small-scale hydroelectric plants, primarily run-of-the-river designs, are regularly subjected to hard particle wear and cavitation erosion due to the wide range of operating points. Depending on the severity of the operating conditions and erosion damage experienced by the machine throughout its service life, the operating companies of these facilities will be impacted. The impact will be technical, operational, logistical, and economic. A small-scale generation plant located in Amaime River in Colombia, is one such case, where severe wear occurs in the turbine components, with a consequent reduction of efficiency. In this study, the analysis of the erosion damage has been expanded and supplemented by computational fluid dynamics (CFD). From this approach, correlations between the wear rate and power output were obtained. Likewise and in conjunction with the computer estimates, a methodology to analyse the costs associated with wear based on historical data of operation was developed, creating a strategy of operation based on a stopping criterion that depends primarily on sediment concentration, turbinated flow, and wear level. The methodology optimizes the use of generators, which takes into consideration the revenue generation and the costs associated with operation and maintenance of pieces under conditions of intrinsic erosion wear in the facility.

The black liquor is a byproduct of the kraft pulping process that contains more than half of the exergy content in the total woody biomass fed to the digester, representing a key supply of renewable energy to the pulping process. In this work, the conventional scenario of the black liquor use (i.e., concentration and combustion) is compared with the black liquor upgrading (via) gasification process for ammonia production in terms of economics, exergy efficiency and environmental impact. The combined energy integration and exergy analysis is used to identify the potential improvements that may remain hidden to the energy analysis alone, namely, the determination and mitigation of the process irreversibility. As a result, the exergy efficiencies of the conventional and the integrated cases average 40% and 42%, respectively, whereas the overall emission balance varies from 1.97 to −0.69 tCO2/tPulp, respectively. The negative CO2 emissions indicate the environmental benefits of the proposed integrated process compared to the conventional kraft pulp mill.

espanolSe presentan los resultados de un estudio sobre la significancia y la optimizacion de algunas variables (granulometria, velocidad de aire, contenido de biomasa y disposicion del reactor) en el poder calorifico del gas de sintesis obtenido de la gasificacion de biomasa (carbon vegetal y cuesco de palma africana). Mediante un diseno de experimento se evaluaron las cuatro variables que oscilaban entre 8-13mm para la granulometria, 0.8-1.4m/s para la velocidad del aire, 0-100 para el contenido de biomasa y ascendente-descendente para la disposicion del reactor. Se encontro que los factores correspondientes a la granulometria y el contenido de biomasa resultan ser los mas significativos en el poder calorifico del gas. Un poder calorifico maximo de 3.84MJ/Nm3 se obtuvo con la disposicion descendente del reactor, alimentacion de carbon vegetal con granulometria de 13mm y suministro maximo de flujo de aire. La verificacion del punto optimo de operacion mostro que tales condiciones de operacion favorecian la produccion de un gas con un alto poder calorifico. EnglishThe results of study on the significance and the optimization of some variables (particle size, air flow, biomass content and reactor disposition) in the calorific value of the synthesis gas obtained by gasification process of biomass (vegetal coal and biomass African palm) is presented. The four variables ranged from 8-13mm for the particle size, 0.8-1.4m/s for air flow, 0-100 for biomass content and updraft-downdraft disposition for the type of reactor were evaluated by an experimental design. It was found that the particle size and biomass content are the most significant factors to maximize the output calorific value of syngas. A maximum calorific value of 3.84MJ/Nm3 was obtained using the downdraft reactor with 13mm particle size and maximum air flow supply. The verification of the optimum operating point under these conditions showed that such operating conditions favored the production of a gas with high calorific value.

A reverse osmosis system driven by photovoltaic energy is an eco-friendly and sustainable way to produce freshwater in rural areas without connection to a power grid and with available brackish water sources. This paper describes a project where a photovoltaic-driven low-pressure reverse osmosis system (LPRO-PV) was designed, tested under laboratory conditions, and installed in Samalayuca, Chihuahua, Mexico, to evaluate the technical feasibility and social impact of this technology. The LPRO-PV system was tested with synthetic water with a salinity of 2921 ± 62.3 mg/L; the maximum freshwater volume produced was 1.8 ± 0.06 m3/day with a salinity value of 91 ± 1.9 mg/L. The LPRO-PV system satisfied the basic freshwater requirements for a local family of three members for one year, including the mobility-restriction period due to the COVID-19 pandemic. The social evaluation analysis reflects the importance of considering the technical aspects derived from the experimental tests, as well as the users’ perception of the performance and operation of the system. As a result of the implementation of this technology and the benefits described by the users, they committed to the maintenance activities required for the LPRO-PV system’s operation. This technology has great potential to produce fresh water in arid and isolated regions with high-salinity groundwater sources, thus fulfilling the human right to safe and clean drinking water.

Currently Smart Grids are considered as an optimum model for energy supply. It improves the efficiency, reliability and availability of the electricity supply. It uses structures to achieve compliance with interoperation that are used across the entire network. To achieve this, special devices are distributed through the entire grid. A RMU (Ring Main Unit) is a device that makes measurements of electrical variables of the grid and sends wirelessly information to a central station MTU (Master Terminal Unit). The RMU has the capacity to detect failures and perform control by disconnecting the grid. In this article, it is shown the design and manufacture of a scale RMU.

This work is the result to the study a different systems of exhaust pipes. The manufacturers of motorbike use a system with several volumes to reduce noise and use a catalyst to reduce emissions. In contrast, the manufacturers of exhaust system decided made a system using a perforated pipe and a rock wool to noise reducing. This system changes the pressure drop and temperature of exhaust gases and, therefore, request a different composition of catalyst.In this communication, it is shown the tests released in a test bench according with the cycle WLTC and the limits are the defined for EURO3. Where, we have changed the type of catalyst, the diameter of the end pipe and the calibration of electronic control unit of engine in order to measure following the test of homologation.The results of the different experiments indicate is very important the pressure drop in the replace exhaust system must be similar to the original system. The composition of the catalyst and the operating temperature are critical to reduce the emissions and the calibration of engine is the main influence. Keywords: Exhaust systems, Catalyst, Regulatory emissions, WLTC

Abstract Solar refrigeration projects both national and international with sorption and other refrigeration systems have been developed in Mexico and other Latin American countries in the last 15 years. A review of the main projects, both for solar cooling and refrigeration and the results obtained are presented in this paper. A methodology where 19 solar technologies for cooling were identified is also presented. Although solar cooling is still not an economically viable technology, the advances made and the experience gained in the projects described and the improved systems envisaged, will make solar refrigeration systems play an important role in the future.