• Energy Research
• other engineering and technologies close
• DE close
• BE close

Abstract The implementation of occupancy-controlled and daylighting-dimmed lighting systems has an impact on the energy consumption of residential buildings. The BAC factor method of EN ISO 52120-1 estimates that 8% of the lighting energy can be saved compared to conventional manual control. However, it is assumed that their ability to potentially lower the lighting energy consumption is strongly related to external factors, such as the extent of daylight entrance and the behaviour of the inhabitants. By means of simulations in EnergyPlus, the performances of automated and manual lighting control are compared for an apartment and semi-detached building located in Brussels (Belgium) with variation in the occupant behaviour and orientation. It appears that an automated lighting control including 0-100% dimmer reduces the lighting energy demand for all investigated cases with savings up to 38.4%, whereas a similar control without dimmer does not necessarily reduce the lighting electricity demand. However, the results show a considerable variation, making prediction methods as the BAC factor method highly inaccurate. The actual relative energy performance depends on the automation system, type of building, orientation and occupant behaviour (i.e. number of inhabitants and occupancy rate). Hereby, the number of inhabitants has the most considerable impact on the relative energy performances with differences up to 50%, while the occupancy rate shows a significant correlation, especially for low numbers of inhabitants.

Abstract Building-based active envelopes play an important role to reduce active heating supplies. Several techniques are developed to enhance the energy performances of active building envelopes; meanwhile, numerous numerical and mathematical models are also developed to conduct the performance analysis of these techniques. In this paper, we propose a state-space model for solar active wall-based Phase Change Materials (PCM). The advantage of this method remains in its simplicity to provide details of internal nodes and input/output parameters. The low-cost calculation is a supplementary advantage versus a heavy numerical method. The proposed numerical model is applied for a multi-layer wall with PCM Wallboards (PCMW) embedded between indoor and outdoor environments. The results show the ability of the state-space model to estimate the thermal behavior of the system, as well as the thermal characteristics of embedding PCM in the internal face of the wall. It significantly contributes to stabilize the indoor temperature and to ensure the thermal comfort.

Abstract In many visions and roadmaps, there is a broad agreement that fuel cells – both for stationary and mobile applications – are the key technology to allow the development of a hydrogen infrastructure. Furthermore, this development is generally thought to be based on a gradual, decentralised evolution. Nevertheless, in this paper it is argued that, taking into account the entire hydrogen chain (production, transport, storage, distribution and end-use), this decentralised fuel-cell based philosophy shows some serious flaws. Therefore, a new hydrogen-transition approach was pushed forward: mixing in of hydrogen into the natural-gas bulk. Using Flanders – the Northern part of Belgium – as a case study, the development of a transitory hydrogen infrastructure has been studied, taking into account the entire hydrogen chain and its dynamics, from production to end use. In a next step, this transition is being quantified. An optimisation model has been developed using Matlab and the commercial solvers GAMS and CPLEX. Following a mixed-integer linear-programming approach, this model is able to determine the economically optimal hydrogen-production mix and operational behaviour of each hydrogen-production plant separately. The model then allows gaining valuable insights in the importance of storage and the influence of fuel prices and carbon taxes with regard to the development of an early hydrogen economy.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Two stage premixed combustor with variable geometry has been developed to meet stringent NOx goals in Japan without the use of water or steam injection. This combustion system is planned to be applied for 120-MW gas turbine in 1090-MW LNG combined cycle plant. The full-pressure, full-scale combustion tests were conducted over a wide range of operating conditions for this gas turbine. The combustion tests proved that NOx levels as well as mechanical characteristics were well within the goals.

Abstract The elemental dissolution of Cu-Zn alloys was investigated as a function of Zn content ranging from 0 to 45 wt%. Atomic emission spectroelectrochemistry (AESEC) was utilized to directly monitor Cu2+ and Zn2+ release and oxide growth as function of time during potentiodynamic experiments. It was determined that Cu dissolution undergoes a simultaneous mechanism of Cu2O formation and Cu2+ release. The addition of Zn in Cu-Zn alloy does not measurably change the dissolution mechanism of Cu2+ and the rate of aqueous Cu2+ was only dependent on the potential. Zn dissolution was however blocked by the formation of a Cu(0) film which shifted the Zn dissolution in the anodic direction.

Abstract Protection devices are designed to provide high sensitivity to transients produced by undesirable conditions like lightning stroke, avoiding their operation under all tolerable events like switching operations. The problem of incorrect operation due to transient phenomena can be handled by two means, one is to allow the transients and provide additional logics in the relay, other means is to damp the oscillation from source side. Protection relays’ not always must trip or send a trip signal and sometimes, only an alarm is necessary. In this context, this research presents a fast and reliable formulation for transmission lines (TLs) switching operations and lightning strokes detection and identification. The proposed methodology is based on Principal Component Analysis (PCA) and Euclidean Norm (EN); by using PCA it is possible to determine that normal operation signals describe a very well defined Ellipsoidal Pattern (EP). In this manner, by calculating the Euclidean Norm (EN) among Principal Components (PCs) for each sample and the origin of the reference Ellipsoidal Pattern, switching operations and lightning strokes are detected and identified. Test results show that the proposed algorithm presents high success on phenomena detection and identification, presenting a high potential for online applications.

Abstract Thermal energy storage with phase change materials (PCM) provides high storage capacities in small temperature intervals. For the design of storage systems, the enthalpy curve of the used PCM has to be known with high precision. The T-History method has evolved to a widely used method for the measurement of the enthalpy as a function of temperature of PCM because of its simplicity and the advantage to be able to investigate larger sample volumes than typically used for differential scanning calorimeters. In order to ensure isothermal specimen during the measurement a thermal insulation is often mounted around the sample holder, but this insulation material is not considered in the evaluation model. In this work a new evaluation model for insulated T-History setups is developed by an analytical heat balance. This model is validated by numerical simulations of insulated T-History measurements and experimentally. By the use of the new model for the evaluation of the enthalpy a significant increase of accuracy can be achieved.

This article presents numerical prediction of a thermoacoustic limit cycle in an industrial gas turbine combustor. The case corresponds to an experimental high pressure test rig equipped with the full-scale Siemens SGT-100 combustor operated at two mean pressure levels of 3 bar and 6 bar. The Flame Transfer Function (FTF) characterising the global unsteady response of the flame to velocity perturbations is obtained for both operating pressures by means of incompressible Large Eddy Simulations (LES). A linear stability analysis is then performed by coupling the FTFs with a wave-based low order thermoacoustic network solver. All the thermoacoustic modes predicted at 3 bar pressure are stable; whereas one of the modes at 6 bar is found to be unstable at a frequency of 231 Hz, which agrees with the experiments. A weakly nonlinear stability analysis is carried out by combining the Flame Describing Function (FDF) predicted by LES with the low order thermoacoustic network solver. The frequency, mode shape and velocity amplitude corresponding to the predicted limit cycle at 209 Hz are used to compute the absolute pressure fluctuation amplitude in the combustor. The numerically reconstructed amplitude is found to be reasonably close to the measured dynamics.