• Energy Research
• Open Access close
• engineering and technology close
• CN close
• DE close
• CA close

In recent years, the rapid development of the rare earth industry has had a serious impact on the environment. Some enterprises have taken measures to improve the production process. In order to explore the sustainability of this industry and these improvements’ environmental benefits, this paper combines emergy analysis and lifecycle assessment to evaluate and compare the production process of rare-earth oxides considering the three aspects of emergy flow, pollutant emissions, and emergy-based indicators. Changes in the emergy of pollutant emissions before and after improvement of the production process are discussed. The results show that the greatest inputs in the mining and beneficiation stage and smelting separation stage are labor force and service and non-renewable resources, respectively. These two production stages are highly dependent on external input and have weak competitiveness. Both stages place great pressure on the environment, so the bastnasite production process would be unsustainable in the long term. After the improvement, the environmental impact of the production process for bastnaesite changed significantly, indicating that the improvement effect of the wastewater treatment facilities and the change of fuel from coal to natural gas is remarkable.

AbstractThe fluid flow characteristics in shale fractures are of great significance for shale gas reservoir evaluation and exploitation. In this study, artificial tension fractures in shale were used to simulate the hydraulic fractures formed by fracturing, and a gas flow test under different pressure gradients was conducted. The nonlinear gas flow and stress‐dependent permeability characteristics were analyzed. The experimental results show the following: (a) CO2 flow in shale fractures exhibits strong nonlinearity. Forchheimer's law, which considers gas compressibility, satisfactorily describes the nonlinear relationship between the flow rate and the pressure gradients in shale fractures. (b) The permeability sensitivity of shale fractures under stress is very strong, and the exponential relationship better describes the pressure dependency of the permeability for the tested shale samples. The permeability of the shale fractures is similar when measured parallel or perpendicular to bedding. Furthermore, the pressure dependence of fractures in shale obeys the Walsh permeability model. (c) As the effective stress increases, the nonlinear flow behavior appears earlier. Based on the Reynolds number and the nonlinear coefficient, a friction factor model is proposed. (d) The normalized transmissivity exhibits a strong correlation with the Reynolds number. CO2 flow through shale fractures is generally dominated by transitional flow. The critical Reynolds number ranges from 1.8 to 102.88 and decreases with increasing effective stress.

Hydrothermal liquefaction (HTL) is an effective way to treat solid wastes with high moisture content. The co-hydrothermal liquefaction (co-HTL) experiments of oily scum and poplar sawdust biochar at the different hydrothermal temperatures were performed in this work. The changes of the appearance and components of the liquid products were comprehensively studied. The results showed that the addition of biochar into oily scum significantly reduced the moisture content of the residue hydrochars obtained after co-HTL. As the hydrothermal temperature increased, the liquid products obtained from co-HTL turned clearer and lighter in color, and the recovery rate of the liquid products significantly increased. The co-HTL of bi-ochar and oily scum could effectively improve the liquid quality and enhance the recovery rate of hydrochars. The carbon numbers of the liquid products obtained from co-HTL were concentrated in C5-C11, which were main compositions of gas-oline. This work can provide basic data and theoretical reference for oily scum efficient treatment and engineering practice.

Decarbonizing the building sector is extremely important to mitigating climate change as the sector contributes 40% of the overall energy consumption and 36% of the total greenhouse gas emissions in the world. Net-zero energy buildings are one of the promising decarbonization attempts due to their potential of decreasing the use of energy and increasing the total share of renewable energy. To achieve a net-zero energy building, it is necessary to decrease the energy demand by applying efficiency enhancement measures and using renewable energy sources. Net-zero energy buildings can be classified into four models (Net-Zero Site Energy buildings, Net-Zero Emissions buildings, Net-Zero Source Energy buildings, and Net-Zero Cost Energy buildings). A variety of technical, financial, and environmental factors should be considered during the decision-making process of net-zero energy building development, justifying the use of multi-criteria decision analysis methods for the design of net-zero energy buildings. This paper also discussed the contributions of renewable energy generation (hydropower, wind energy, solar, heat pumps, and bioenergy) to the development of net-zero energy buildings and reviewed its role in tackling the decarbonization challenge. Cost-benefit analysis and life cycle assessment of building designs were reviewed to shape the priorities of future development. It is important to develop a universal decision instrument for optimum design and operation of net-zero energy buildings.

Pool boiling in porous media has been applied in various thermal management systems by using latent heat and increasing the heat transfer area and thermal conduction path to improve the heat transfer performance. In mechanical equipment, vibration is an inevitable problem due to reasons such as engine operation and high-speed relative motion between transmission system components, which causes the system components to be affected by vibration forces or vibration accelerations. This study focuses on a review of published articles about the effects of mechanical vibration on the characteristics of boiling process in porous media by two aspects: heat transfer performance and bubble dynamics. Heat transfer coefficient (HTC) and critical heat flux are two main parameters used to measure the boiling heat transfer characteristics of porous media. For bubble dynamics investigations, properties such as migration, fragment, coalescence, departure diameter and frequency are the focus of research attention. Different mechanical vibration parameters, i.e., direction, frequency, and amplitude, will have different effects on the above characteristics. It is worth mentioning that the greatest influence occurs under resonance conditions, and this has been verified through experimental and simulation calculations. This review highlights the importance of considering mechanical vibrations in the design and optimization of porous media systems for efficient heat transfer applications. Further research is warranted to explore the detailed mechanisms and optimize the vibration parameters for enhanced heat transfer performance in thermal management systems using porous media.

To mitigate the temperature increase in urban environments and reduce its impact on energy consumption and the quality of the environment, urban retrofitting technologies have been developed and applied worldwide. High albedo in urban surfaces and additional vegetation are the most efficient strategies to accomplish these goals. The objective of this study is to estimate the weight of these strategies, both individually and integrated, on the cooling potential of two Latin American cities. To do this, 36 low and high urban density scenarios were simulated with the ENVI-Met software. The simulation models were calibrated using air temperature curves which were monitored during the summer periods from 2010 to 2013. A Principal Components Analysis was carried out to establish possible associations between the proposed mitigation strategies and then the weight of anthropogenic heat was evaluated according to the configuration. The results show that the integrated mitigation strategies in urban areas -i. e. increase vegetation and albedo on horizontal surfaces- has a great potential to mitigate urban warming, showing a more significant impact on low-density urban configuration. The contribution of anthropogenic heat mainly produced by motorized transport and air conditioning systems, is a crucial input data for the urban microclimate simulations. Its impact on the urban densification processes may cancel out the benefits derived by the application of the mitigation strategies considered.

The battery power state (SOP) is the basic indicator for the Battery management system (BMS) of the battery energy storage system (BESS) to formulate control strategies. Although there have been many studies on state estimation of lithium-ion batteries (LIBs), aging and temperature variation are seldom considered in peak power prediction during the whole life of the battery. To fill this gap, this paper aims to propose an adaptive peak power prediction method for power lithium-ion batteries considering temperature and aging is proposed. First, the Thevenin equivalent circuit model is used to jointly estimate the state of charge (SOC) and SOP of the lithium-ion power battery, and the variable forgetting factor recursive least squares (VFF-RLS) algorithm and extended Kalman filter (EKF) are utilized to identify the battery parameters online. Then, multiple constraint parameters including current, voltage, and SOC were derived, considering the dependence of the polarization resistance of the battery on the battery current. Finally, the verification experiment was carried out with LiFePO4 battery. The experimental results under FUDS operating conditions show that the maximum SOC estimation error is 1.94%. And the power prediction errors at 20%, 50%, and 70% SOC were 5.0%, 8.1% and 4.5%, respectively. Our further work will focus on the joint estimation of battery state to further improve the accuracy.

AbstractVentilation door are commonly found in tunnels and other underground engineering ventilation structures, disaster periods using its explosion isolation, explosion relief, wind regulation characteristics for disaster prevention and mitigation is of great significance. This paper numerically simulates the propagation characteristics of the gas explosion shock wave in the nearby tunnel when the ventilation door are opened at different degrees, and analyzes the influence mechanism of the opening degree on the change law of the shock wave overpressure distribution in the nearby tunnel. The results show that the shock wave forms a strong turbulence area (high pressure area) on both sides in front of the ventilation door, and the area range and the overpressure value decrease with the increase of the opening degree; the ventilation door reduce the intensity of the shock wave, so that the overpressure behind the ventilation door decreases, and the smaller the opening degree, the lower the overpressure behind the ventilation door. The secondary explosion formed shock wave and the ventilation door reflected shock wave meet to form a stronger shock wave, which leads to different opening degrees of ventilation door, its before, after the roadway and after the bifurcation of the main roadway in the measured points of the overpressure change curve is different, the main difference is that the peak overpressure for the first wave or the second wave peak. The peak overpressure in the tunnel before and after the ventilation door decreases and increases respectively with the increase of the opening length, and the overall decay of the peak overpressure at 5 m and 10 m before the ventilation door is 49.56% and 4.04% respectively and only has an effect on the peak overpressure in main tunnel within 20 m from the bifurcation.