• Energy Research
• 2021-2025close
• DE close
• EU close
• RU close
• Energies close

This research looked at the state of soils faced with urbanization processes in the Arctic region of the Yamal-Nenets Autonomous District (YANAO). Soils recently used in agriculture, which are now included in the infrastructure of the cities of Salekhard, Labytnangi, Kharsaim, and Aksarka in the form of various parks and public gardens were studied. Morphological, physico-chemical, and agrochemical studies of selected soils were conducted. Significant differences in fertility parameters between urbanized abandoned agricultural soils and mature soils of the region were revealed. The quality of soil resources was also evaluated in terms of their ecotoxicology condition, namely, the concentrations of trace metals in soils were determined and their current condition was assessed using calculations of various individual and complex soil quality indices.

Both electrical and thermal efficiencies combine in determining and evaluating the performance of a PV/T collector. In this study, two PV/T systems consisting of poly and monocrystalline PV panels were used, which are connected from the bottom by a heat exchanger consisting of a spiral tube through which a nanofluid circulates. In this study, a base fluid, water, and ethylene glycol were used, and iron oxide nanoparticles (nano-Fe2O3) were used as an additive. The mixing was carried out according to the highest specifications adopted by the researchers, and the thermophysical properties of the fluid were carefully examined. The prepared nanofluid properties showed a limited effect of the nanoparticles on the density and viscosity of the resulting fluid. As for the thermal conductivity, it increased by increasing the mass fraction added to reach 140% for the case of adding 2% of nano-Fe2O3. The results of the zeta voltage test showed that the supplied suspensions had high stability. When a mass fraction of 0.5% nano-Fe2O3 was added the zeta potential was 68 mV, while for the case of 2%, it reached 49 mV. Performance tests showed a significant increase in the efficiencies with increased mass flow rate. It was found when analyzing the performance of the two systems for nanofluid flow rates from 0.08 to 0.17 kg/s that there are slight differences between the monocrystalline, and polycrystalline systems operating in the spiral type of exchanger. As for the case of using monocrystalline PV the electrical, thermal, and total PV/T efficiencies with 2% added Fe2O3 ranged between 10% to 13.3%, 43–59%, and 59 to 72%, respectively, compared to a standalone PV system. In the case of using polycrystalline PV, the electrical, thermal, and total PV/T efficiencies ranged from 11% to 13.75%, 40.3% to 63%, and 55.5% to 77.65%, respectively, compared to the standalone PV system. It was found that the PV/T electrical exergy was between 45, and 64 W with thermal exergy ranged from 40 to 166 W, and total exergy from 85 to 280 W, in the case of using a monocrystalline panel. In the case of using polycrystalline, the PV/T electrical, thermal, and total exergy were between 45 and 66 W, 42–172 W, and 85–238 W, respectively. The results showed that both types of PV panels can be used in the harsh weather conditions of the city of Baghdad with acceptable, and efficient productivity.

In this study, our aim was to explore the potential energy savings obtainable from the recycling of 1 tonne of Construction and Demolition Waste (C&DW) generated in the Metropolitan City of Naples. The main fraction composing the functional unit are mixed C&DW, soil and stones, concrete, iron, steel and aluminium. The results evidence that the recycling option for the C&DW is better than landfilling as well as that the production of recycled aggregates is environmentally sustainable since the induced energy and environmental impacts are lower than the avoided energy and environmental impacts in the life cycle of recycled aggregates. This LCA study shows that the transition to the Circular Economy offers many opportunities for improving the energy and environmental performances of the construction sector in the life cycle of construction materials by means of internal recycling strategies (recycling C&DW into recycled aggregates, recycled steel, iron and aluminum) as well as external recycling by using input of other sectors (agri-food by-products) for the manufacturing of construction materials. In this way, the C&D sector also contributes to realizing the energy and bioeconomy transition by disentangling itself from fossil fuel dependence.

The rapid increase in the penetration of photovoltaic (PV) power plants results in an increased risk of grid failure, primarily due to the intermittent nature of the plant. To overcome this problem, the flexible power point tracking (FPPT) algorithm has been proposed in the literature over the maximum power point tracking (MPPT) algorithm. These algorithms regulate the PV power to a certain value instead of continuously monitoring the maximum power point (MPP). The proposed work carries out a detailed comparative study of various constant power generation (CPG) control strategies. The control strategies are categorized in terms of current-, voltage-, and power-based tracking capabilities. The comparative analysis of various reported CPG/FPPT techniques was carried out. This analysis was based on some key performance indices, such as the type of control strategy, irradiance pattern, variation in G, region of operation, speed of tracking, steady-state power oscillations, drift severity scenario, partial shading scenario, implementation complexity, stability, fast dynamic response, robustness, reactive power, cost, and tracking efficiency. Among existing FPPT algorithms, model-based control has a superior performance in terms of tracking speed and low steady-state power oscillations, with a maximum tracking efficiency of 98.57%.

The application of voltage reduction in medium and low voltage grids to reduce peak power demand or energy consumption has been implemented since the 1980s using several approaches. Conservation Voltage Reduction (CVR), as one such approach, uses a voltage control device to reduce or increase the voltage setpoint on a busbar, thereby reducing or increasing the amount of active and reactive power supply in the network. Voltage regulation for CVR is always implemented according to established network planning standards in each country. Research in this field has proven that a CVR factor (CVRf) of 0.7–1.5 for peak demand reduction can be achieved. This is an evaluation metric of CVR. The aim of this research is to determine and validate CVRf for peak demand reduction by comparing actual results obtained during regular tap changes with other randomly distributed periods outside tap change operations, using a set of measurement data. It is important to understand CVR deployment capability by evaluating CVR potentials from historical random tap operations before a robust network-wide deployment is introduced. This research provides such guidance. It also provides a novel approach to determining tap changes from voltage measurements using a time-based algorithm. A CVRf ranging from 0.95 to 1.61 was estimated using a measurement dataset from a test field. The result of the entire evaluation shows that the CVRf are smaller during peak PV production and greater during peak demand periods. Further evaluation using statistical hypotheses testing and a control chart was used to validate the evaluation.

The growing number of electric vehicles in recent years is observable in almost all countries. The country’s energy transition should accompany this rise in electromobility if it is currently generated from non-renewable sources. Only electric vehicles powered by renewable energy sources can be considered zero-emission. Therefore, it is essential to conduct interdisciplinary research on the feasibility of combining energy recovery/generation structures and testing the energy consumption of electric vehicles under real driving conditions. This work presents a comprehensive approach for evaluating the energy consumption of a modern public building–electric vehicle system within a specific location. The original methodology developed includes surveys that demonstrate the required mobility range to be provided to occupants of the building under consideration. In the next step, an energy balance was performed for a novel near-zero energy building equipped with a 199.8 kWp photovoltaic installation, the energy from which can be used to charge an electric vehicle. The analysis considered the variation in vehicle energy consumption by season (winter/summer), the actual charging profile of the vehicle, and the parking periods required to achieve the target range for the user.

The use of natural gas as an energy source is increasing significantly due to its low greenhouse gas emissions. However, the common methods of natural gas storage and transportation, such as liquefied or compressed natural gas, are limited in their applications because they require extreme conditions. Gas hydrate technology can be a promising alternative to conventional approaches, as artificially synthesized hydrates provide an economical, environmentally friendly, and safe medium to store energy. Nevertheless, the low rate of hydrate formation is a critical problem that hinders the industrial application of this technology. Therefore, chemical promoters are being developed to accelerate the kinetics of gas hydrate formation. In this paper, the effect of new sodium sulfosuccinate compounds, synthesized based on glycerol and pentaerythritol, on methane hydrate formation was studied. Experiments under dynamic conditions using high-pressure autoclaves demonstrated that the conversion of water-to-hydrate forms increased from 62 ± 5% in pure water to 86 ± 4% for the best promoter at concentration 500 ppm. In addition, the rate of hydrate formation increases 2–4 times for different concentrations. Moreover, none of the synthesized reagents formed foam, compared to sodium dodecyl sulfate, in which the foam rate was 3.7 ± 0.2. The obtained reagents showed good promotional properties and did not form foam, which makes them promising promoters for gas hydrate technology.

Background. Laws that enable a circular economy (CE) are being enacted globally, but reliable standardized and digitized CE data about products is scarce, and many CE platforms have differing exclusive formats. In response to these challenges, the Ministry of The Economy of Luxembourg launched the Circularity Dataset Standardization Initiative to develop a globalized open-source industry standard to allow the exchange of standardized data throughout the supply cycle, based on these objectives: (a) Provide basic product circularity data about products. (b) Improve circularity data sharing efficiency. (c) Encourage improved product circularity performance. A policy objective was to have the International Organization for Standardization (ISO) voted to create a working group. Methods. A state-of-play analysis was performed concurrently with consultations with industry, auditors, data experts, and data aggregation platforms. Results. Problem statements were generated. Based on those, a solution called Product Circularity Data Sheet (PCDS) was formulated. A proof of concept (POC) template and guidance were developed and piloted with manufacturers and platforms, thus fulfilling objective (a). For objective (b), IT ecosystem requirements were developed, and aspects are being piloted in third party aggregation platforms. Objective (c) awaits implementation of the IT ecosystem. The policy objective related to the ISO was met. Conclusions and future research. In order to fully test the PCDS, it is necessary to: conduct more pilots, define governance, and establish auditing and authentication procedures.