• Energy Research
• Closed Access close
• Restricted close
• 7. Clean energy close
• 13. Climate action close
• 12. Responsible consumption close
• DE close
• JP close
• NL close

Interfacial resistance at electrode‐high Li+ conductive solid electrolytes must be reduced well to develop high‐power all‐solid‐state batteries using oxide‐based solid electrolytes (Ox‐SSBs). Herein, crystalline electrode films of LiCoO2 (LCO) are formed on a high Li+ conductive crystalline‐glass solid electrolyte sheet, Li1.3Al0.3Ti2(PO4)3 (LATP) (σ25 °C = 1 × 10−4 S cm−1), at room temperature by aerosol deposition (AD), and the effects of the annealing temperature on the interfacial resistivities (Rint) at the LCO/LATP are investigated. The Rint visibly increases by annealing over 500 °C with the growth of Co3O4 as a reactant. In contrast, Rint is reduced to ≈100 Ω cm2 by low‐temperature annealing at 250–350 °C due to superior contact through the structural rearrangement of an artificial metastable interface formed by the AD. These results are applied to bulk‐type Ox‐SSB, Li/Li7La3Zr2O12(LLZ)/LCO–LATP, and our best Ox‐SSB delivers a discharge capacity of 100 mA cm−2 at 100 °C.

In order to exploit renewable energies from tidal stream, tandem propellers of a unique counter-rotating type horizontal-axis tidal turbine was firstly designed based on the blade element momentum (BEM) theory. And then a multi-objective numerical optimization method coupled the response surface method (RSM) with the genetic algorithm (GA) was employed to obtain desirable blade profiles. The front blade pitch angle distribution was taken as optimization variable in this paper, as it plays an important role in affecting the inlet conditions of the rear blade. The numerical results show that both optimization objectives of power coefficient and thrust coefficient can be significantly improved. It was verified that the performance of the power unit with the optimized blades increases obviously by optimizing the pitch angle.

Current energy market designs and pricing schemes fail to give investors the appropriate market signals. In particular, energy prices are not high enough to attract investors to build new or maintain existing power capacity. In this paper we propose a method to compute second-best Pareto optimal equilibrium prices for any market exhibiting non-convexities and, based on this result, an energy market design able to restore the correct energy price signals for supply investors.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

Direct Load Control (DLC) is an effective instrument for achieving a guaranteed load curtailment. Unfortunately, if a customer considers that personal discomfort outweighs money savings after DLC shutting down of home appliances, DLC solution can be rejected. This paper proposes the way to remediate customer comfort concerns by pre-storing additional energy in electric loads before their disconnection from the grid. We take electric tank water heaters as an illustrative example of residential loads with storage. To illuminate our approach we first show how to balance electric consumption for pre-storing with user thermal discomfort for a single water heater. Then, we illustrate how the approach can be scaled-up to a multiple-boiler scenario, when ten remotely controlled boilers act next to fifty non-controlled boilers. The simulations for the latter case show that the expected user thermal discomfort can be significantly reduced at the cost of a reasonable increase of electricity demand preceding DLC event.

The unpredictable nature of wind energy makes its integration to the electric grid highly challenging. However, these challenges can be addressed by incorporating storage devices (batteries) in the system. We perform an overall assessment of a single domestic power system with a wind turbine supported by an energy storage device. The aim is to investigate the best operation mode of the storage device such that the occurrence of large power spills can be minimized. For estimating the small probability of large power spills, we use the splitting technique for rare-event simulations. An appropriate Importance Function for splitting is formulated such that it reduces the work-load of the probability estimator as compared to the conventional Crude Monte Carlo probability estimator. Simulation results show that the ramp constraints imposed on the charging/discharging rate of the storage device plays a pivotal role in mitigating large power spills. It is observed that by employing a new charging strategy for the storage device large power spills can be minimized further. There exists a trade-off between reducing the large power spills versus reducing the average power spills.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.