• Energy Research
• engineering and technology close
• 12. Responsible consumption close
• DE close
• JP close

Given the global energy and environmental situation, the European Union has been issuing directives with increasingly demanding requirements in term of the energy efficiency in buildings. The international competition of sustainable houses, Solar Decathlon Europe (SDE), is aligned with these European objectives. SDE houses are low energy solar buildings that must reach the near to zero energy houses’ goal. In the 2012 edition, in order to emphasize its significance, the Energy Efficiency Contest was added. SDE houses’ interior comfort, functioning and energy performance is monitored. The monitoring data can give an idea about the efficiency of the houses. However, a jury comprised by international experts is responsible for carrying out the houses energy efficiency evaluation. Passive strategies and houses services are analyzed. Additionally, the jury's assessment has been compared with the behavior of the houses during the monitoring period. Comparative studies make emphasis on the energy aspects, houses functioning and their interior comfort. Conclusions include thoughts related with the evaluation process, the results of the comparative studies and suggestions for the next competitions.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

COVID-19 pandemic has brought tremendous environmental burden due to huge amount of medical wastes (about 54,000 t/d as of November 22, 2020), including face mask, gloves, clothes, goggles, and sanitizer/disinfectant containers. A proper waste management is urgently required to mitigate the spread of the disease, minimize the environmental impacts, and take their potential advantages for further utilization. This work provides a prospective review on the possible thermochemical treatments for those COVID-19 related medical wastes (CMW), as well as their possible conversion to fuels. The characteristics of each waste are initially analyzed and described, especially their potential as energy source. It is clear that most of CMWs are dominated by plastic polymers. Thermochemical processes, including incineration, torrefaction, pyrolysis, and gasification, are reviewed in terms of applicability for CMW. In addition, the mechanical treatment of CMW into sanitized refuse-derived fuel (SRDF) is also discussed as the preliminary stage before thermochemical conversion. In terms of material flexibility, incineration is practically applicable for all types of CMW, although it has the highest potential to emit the largest amount of CO2 and other harmful gasses. Furthermore, gasification and pyrolysis are considered promising in terms of energy conversion efficiency and environmental impacts. On the other hand, carbonization faces several technical problems following thermal degradation due to insufficient operating temperature.

AbstractThe future European energy supply system will have a high share of renewable energy sources (RES) to meet the greenhouse gas emission policy of the European Commission. Such a system is characterized by the need for a strongly interconnected energy transport grid as well as a high demand of energy storage capacities to compensate the time fluctuating characteristic of most RE generation technologies. With the RE generators at the location of high harvest potential, the appropriate dimension of storage and transmission system between different regions, a cost efficient system can be achieved. To find the preferred target system, the optimization tool GENESYS (Genetic Optimization of a European Energy System) was developed. The example calculations under the assumption of 100% self-supply, show a need of about 2,500 GW RES in total, a storage capacity of about 240,000 GWh, corresponding to 6% of the annual energy demand, and a HVDC transmission grid of 375,000 GWkm. The combined cost for generation, storage and transmission excluding distribution, was estimated to be 6.87 ct/kWh.

The European Geosciences Union (EGU) brings together geoscientists from all over the world covering all disciplines of the Earth, planetary and space sciences. This geoscientific interdisciplinarity is needed to tackle the challenges of the future. One major challenge for humankind is to provide adequate and reliable supplies of affordable energy and other resources in efficient and environmentally sustainable ways. This Energy Procedia issue provides an overview of the contributions of the Division on Energy, Resources & the Environment (ERE) at the EGU General Assembly 2017.