• Energy Research
• Closed Access close
• Restricted close
• 7. Clean energy close
• 13. Climate action close
• 12. Responsible consumption close
• DE close
• JP close

Interfacial resistance at electrode‐high Li+ conductive solid electrolytes must be reduced well to develop high‐power all‐solid‐state batteries using oxide‐based solid electrolytes (Ox‐SSBs). Herein, crystalline electrode films of LiCoO2 (LCO) are formed on a high Li+ conductive crystalline‐glass solid electrolyte sheet, Li1.3Al0.3Ti2(PO4)3 (LATP) (σ25 °C = 1 × 10−4 S cm−1), at room temperature by aerosol deposition (AD), and the effects of the annealing temperature on the interfacial resistivities (Rint) at the LCO/LATP are investigated. The Rint visibly increases by annealing over 500 °C with the growth of Co3O4 as a reactant. In contrast, Rint is reduced to ≈100 Ω cm2 by low‐temperature annealing at 250–350 °C due to superior contact through the structural rearrangement of an artificial metastable interface formed by the AD. These results are applied to bulk‐type Ox‐SSB, Li/Li7La3Zr2O12(LLZ)/LCO–LATP, and our best Ox‐SSB delivers a discharge capacity of 100 mA cm−2 at 100 °C.

In order to exploit renewable energies from tidal stream, tandem propellers of a unique counter-rotating type horizontal-axis tidal turbine was firstly designed based on the blade element momentum (BEM) theory. And then a multi-objective numerical optimization method coupled the response surface method (RSM) with the genetic algorithm (GA) was employed to obtain desirable blade profiles. The front blade pitch angle distribution was taken as optimization variable in this paper, as it plays an important role in affecting the inlet conditions of the rear blade. The numerical results show that both optimization objectives of power coefficient and thrust coefficient can be significantly improved. It was verified that the performance of the power unit with the optimized blades increases obviously by optimizing the pitch angle.

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

Abstract Thermal energy storage with phase change materials (PCM) provides high storage capacities in small temperature intervals. For the design of storage systems, the enthalpy curve of the used PCM has to be known with high precision. The T-History method has evolved to a widely used method for the measurement of the enthalpy as a function of temperature of PCM because of its simplicity and the advantage to be able to investigate larger sample volumes than typically used for differential scanning calorimeters. In order to ensure isothermal specimen during the measurement a thermal insulation is often mounted around the sample holder, but this insulation material is not considered in the evaluation model. In this work a new evaluation model for insulated T-History setups is developed by an analytical heat balance. This model is validated by numerical simulations of insulated T-History measurements and experimentally. By the use of the new model for the evaluation of the enthalpy a significant increase of accuracy can be achieved.

Abstract Gas crossover is an unavoidable phenomenon in proton exchange membrane fuel cells. Gas crossover leads to heat and water generations without conducting any useful works, hence increasing fuel consumption. Particularly, Gas crossover can result in the degradation and formation of pinholes inside the membrane. Therefore, the gas crossover is a critical factor significantly affecting the durability of a fuel cell and quality of the membrane. Herein, we numerically investigate the effects of gas crossover across the membrane in a proton exchange membrane fuel cell. A two-dimensional, two-phase, steady state model of the gas crossover using the partial differential equation solver FreeFem++, was built to investigate the crossover characteristics of hydrogen and oxygen across the membrane versus changes in operating conditions and various geometric structure of components in the proton exchange membrane fuel cell. Results indicated that higher equivalent weight of Nafion® is required to significantly decrease gas crossover phenomenon while the cell performance was reduced negligibly. In addition, as the increase in the stoichiometric flow ratio and channel length, the gas crossover decreased and the cell performance improved.

Partial discharge (PD) measurement using electromagnetic waves by antennas is a promising technique for diagnosing the insulation performance of gas-insulated switchgear (GIS). In order to establish highly sensitive diagnosis techniques of GIS insulation, frequency characteristics of electromagnetic waves, which are determined by GIS apertures such as insulating spacers and bushings, should be clarified. In this paper, we measure the electromagnetic waves radiated from different GIS apertures and also analyze them using the transient analysis program "PSpice." Comparing the measurements with the theoretical analyses, we investigate the relationship between the GIS aperture configuration and the radiated electromagnetic wave spectrum from the aperture. We also discuss how the aperture condition contributes to the radiation characteristics of electromagnetic waves. Finally, we conclude that the electromagnetic waves radiated from the GIS aperture are based on different radiation mechanisms in frequency.