• Energy Research
• other engineering and technologies close
• DE close
• KR close

Virtually developing of automotive power systems is currently experiencing increasing significance due to elevated vehicular electrification and automation of driving functions. The analysis of system-inherent disturbances requires accurate simulation models for both short-term transients or long-term driving cycles. The electrical behavior of electromechanical actuators such as brake or steering highly depends on the mechanical environmental interaction being dependent many variables. This contribution presents a methodology to extract abstracted models of machine driven actuators on the basis of an electric steering. The dynamics of a complex electromechanical model are investigated using pulse response analysis for differentiated operation points. The obtained model reduction is implemented in a frequency-dependent equivalent circuit.

This paper presents the development of a nodal diffusion code, RAST-V, and its verification and validation for VVER (vodo–vodyanoi energetichesky reactor) analysis. A VVER analytic solver has been implemented in an in-house nodal diffusion code, RAST-K. The new RAST-K version, RAST-V, uses the triangle-based polynomial expansion nodal method. The RAST-K code provides stand-alone and two-step computation modes for steady-state and transient calculations. An in-house lattice code (STREAM) with updated features for VVER analysis is also utilized in the two-step method for cross-section generation. To assess the calculation capability of the formulated analysis module, various verification and validation studies have been performed with Rostov-II, and X2 multicycles, Novovoronezh-4, and the Atomic Energy Research benchmarks. In comparing the multicycle operation, rod worth, and integrated temperature coefficients, RAST-V is found to agree with measurements with high accuracy which RMS differences of each cycle are within ±47 ppm in multicycle operations, and ±81 pcm of the rod worth of the X2 reactor. Transient calculations were also performed considering two different rod ejection scenarios. The accuracy of RAST-V was observed to be comparable to that of conventional nodal diffusion codes (DYN3D, BIPR8, and PARCS).

Large-size woody biomass is a valuable renewable resource to replace fossil fuels in biorefinery processes. The preprocessing of wood chips and briquettes is challenging to manage, especially in an industrial setting, as it generates a significant amount of dust and noise and occasionally causes unexpected accidents. As a result, a substantial amount of resources, energy, labor, and space are needed. The thermochemical conversion behavior of large-size woody biomass was studied to reduce energy consumption for chipping. Large-size wood was 1.5 m in length, 0.1 m in breadth, and stacked 90 cm in height. This strategy has many benefits, including increased effectiveness and reduced CO2 emissions. The target of this paper presents the thermochemical process, and large-size wood was chosen because it provides high-quality product gas while reducing the preprocessing fuel cost. This review examines the benefits of thermochemical conversion technologies for assessing the likelihood of carbon neutrality.

Attempts to model any present or future power grid face a huge challenge because a power grid is a complex system, with feedback and multi-agent behaviors, integrated by generation, distribution, storage and consumption systems, using various control and automation computing systems to manage electricity flows. Our approach to modeling is to build upon an established model of the low voltage electricity network which is tested and proven, by extending it to a generalized energy model. But, in order to address the crucial issues of energy efficiency, additional processes like energy conversion and storage, and further energy carriers, such as gas, heat, etc., besides the traditional electrical one, must be considered. Therefore a more powerful model, provided with enhanced nodes or conversion points, able to deal with multidimensional flows, is being required. This article addresses the issue of modeling a local multi-carrier energy network. This problem can be considered as an extension of modeling a low voltage distribution network located at some urban or rural geographic area. But instead of using an external power flow analysis package to do the power flow calculations, as used in electric networks, in this work we integrate a multiagent algorithm to perform the task, in a concurrent way to the other simulation tasks, and not only for the electric fluid but also for a number of additional energy carriers. As the model is mainly focused in system operation, generation and load models are not developed. The financial support from EPSRC for Liz Varga on project entitled "Transforming Utilities’ Conversion Points" (no. EP/J005649/1) is gratefully acknowledged.

The thermo-hydro-mechanical behaviour of a water-saturated cement-based heat store for domestic applications has been investigated. Numerical simulations have been employed to locate the critical regions during thermal loading, for which analytical solutions have been derived and validated by numerical simulations. The analytical solutions allow a fast screening of materials and design parameters in relation to the stresses induced by thermomechanical loading. Maximum stresses in the system have been quantified based on the thermomechanical properties of three heat exchanger materials selected by design engineers and of the filling material. Sensitivity analyses indicate that the stress distribution is very sensitive to the thermal expansion coefficients of the involved materials. The results of this study can serve as a guide line for the design of the present and similar heat storage systems. The analytical solution developed is a fast and robust method for the evaluation of stresses around heat exchangers embedded in a solid material and can serve as a tool for design optimisation.

SummaryEnvironmentally extended multiregional input‐output (EE MRIO) tables have emerged as a key framework to provide a comprehensive description of the global economy and analyze its effects on the environment. Of the available EE MRIO databases, EXIOBASE stands out as a database compatible with the System of Environmental‐Economic Accounting (SEEA) with a high sectorial detail matched with multiple social and environmental satellite accounts. In this paper, we present the latest developments realized with EXIOBASE 3—a time series of EE MRIO tables ranging from 1995 to 2011 for 44 countries (28 EU member plus 16 major economies) and five rest of the world regions. EXIOBASE 3 builds upon the previous versions of EXIOBASE by using rectangular supply‐use tables (SUTs) in a 163 industry by 200 products classification as the main building blocks. In order to capture structural changes, economic developments, as reported by national statistical agencies, were imposed on the available, disaggregated SUTs from EXIOBASE 2. These initial estimates were further refined by incorporating detailed data on energy, agricultural production, resource extraction, and bilateral trade. EXIOBASE 3 inherits the high level of environmental stressor detail from its precursor, with further improvement in the level of detail for resource extraction. To account for the expansion of the European Union (EU), EXIOBASE 3 was developed with the full EU28 country set (including the new member state Croatia). EXIOBASE 3 provides a unique tool for analyzing the dynamics of environmental pressures of economic activities over time.

Abstract The paper presents an equivalent circuit based simulation model for the static and dynamic behavior of lithium-ion battery systems and explains the different steps of the theoretical and experimental modeling process. The equivalent circuit based model describes the voltage-current characteristic, the state of charge behavior and the occurring losses of the battery system. A parameter identification method based on three characteristic experiments, a cycle test, an open circuit voltage test and pulse tests, is introduced. The model parameters are estimated employing a nonlinear optimization method. Furthermore, the experimental test bed for investigation of lithium-ion battery systems is described. The battery model approach is demonstrated and validated for a commercial 5 kWh lithium-ion battery system, including the model validation for test profiles and emulated battery charging and discharging profiles of a real photovoltaic home storage application. The comparison of measured and simulated voltage profiles indicates an excellent performance of the battery model.