• Energy Research
• engineering and technology close
• 12. Responsible consumption close
• DE close
• CA close
• NL close

Production of biodiesel from yellow grease (waste cooking oil and waste animal fats) is fast emerging as a promising alternative to address the twin challenges before the biodiesel industry today-fluctuation in prices of vegetable oil and the food versus fuel debate. Yellow grease has a high percentage of free fatty acids (FFA) and proves to be an unsuitable feedstock for biodiesel production from commercially viable alkali-catalyzed production systems due to saponification problems.“Green” methodologies based on heterogeneous solid acid catalyzed reactions have the potential to simultaneously promote esterification and transesterification reactions of yellow grease to produce biodiesel without soap formation and offer easy catalyst separation without generation of toxic streams. This paper presents kinetic studies for the conversion of model yellow grease feeds to biodiesel using a heteropolyacid supported on alumina (HSiW/Al2O3) using a batch autoclave. Three model yellow grease feeds were prepared using canola oil with added FFA such as palmitic, oleic and linoleic acid. A pseudo homogeneous kinetic model for the parallel esterification and transesterification was developed. The rate constants and activation parameters for esterification and transesterification reactions for the model yellow grease feeds were determined. The rate constants for esterification are higher than the transesterification rate constants. The kinetic model was validated using the experimental biodiesel data obtained from processing a commercial yellow grease feed. The kinetic model could be used to design novel processes to convert various low-value waste oils, fats and non-food grade oils to sustainable biodiesel. Keywords: Yellow grease, Canola oil, Free fatty acids, Heteropolyacid, Kinetics for esterification and transesterification

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Given the global energy and environmental situation, the European Union has been issuing directives with increasingly demanding requirements in term of the energy efficiency in buildings. The international competition of sustainable houses, Solar Decathlon Europe (SDE), is aligned with these European objectives. SDE houses are low energy solar buildings that must reach the near to zero energy houses’ goal. In the 2012 edition, in order to emphasize its significance, the Energy Efficiency Contest was added. SDE houses’ interior comfort, functioning and energy performance is monitored. The monitoring data can give an idea about the efficiency of the houses. However, a jury comprised by international experts is responsible for carrying out the houses energy efficiency evaluation. Passive strategies and houses services are analyzed. Additionally, the jury's assessment has been compared with the behavior of the houses during the monitoring period. Comparative studies make emphasis on the energy aspects, houses functioning and their interior comfort. Conclusions include thoughts related with the evaluation process, the results of the comparative studies and suggestions for the next competitions.

In the current study, we examine the Indonesian government's watershed management program, which was established in 2001. In 2005, the Coordination Team for Rescue of Water Resources (CTRWR) was established to execute the program on a national level. However, at the time, field implementation was a sectoral interest due to the lack of program integration. To this end, the Indonesian government promoted integrated watershed management in 2009, which since then has been implemented by all stakeholders (in Top–Down management form), with application limited to preparing and planning documents. This is mainly driven by the stakeholders’ lack of understanding with regard to watershed systems as integrated management units. Field implementation results have not yet been realized, including the promotion of community-based watershed management (through Bottom–Up management). The purpose of our research was to determine the index numbers by measuring the level of cooperation between watershed management workers based on the Village Watershed Model (VWM) specifically surface water which includes six variables: planning, participation, institutional, fund sharing, gender, and management systems. The method used was an ordinal measure with the Likert scale. Our data showed successful watershed management, in which five of the six VWM variables—planning, participation, institutional, fund sharing, and management systems—were in the “good” category with indices ranging from 73.08 to 78.27. The gender variable index (69.12) was in the “medium” category.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

As part of the Copenhagen Accord, individual countries have submitted greenhouse gas reduction proposals for the year 2020. This paper analyses the implications for emission reductions, the carbon price, and abatement costs of these submissions. The submissions of the Annex I (industrialised) countries are estimated to lead to a total reduction target of 12-18% below 1990 levels. The submissions of the seven major emerging economies are estimated to lead to an 11-14% reduction below baseline emissions, depending on international (financial) support. Global abatement costs in 2020 are estimated at about USD 60-100 billion, assuming that at least two-thirds of Annex I emission reduction targets need to be achieved domestically. The largest share of these costs are incurred by Annex I countries, although the costs as share of GDP are similar for Annex I as a group and the seven emerging economies as a group, even when assuming substantial international transfers from Annex I countries to the emerging economies to finance their abatement costs. If the restriction of achieving two-thirds of the emission reduction target domestically is abandoned, it would more than double the international carbon price and at the same time reduce global abatement costs by almost 25%.

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.

Abstract The residential sector accounts for most of energy-consumption in developing countries in the form of traditional energy. The use of commercial energy is nominal and confined mostly to urban areas where fuelwood is already monetized. A model, based on an end-use/process analysis approach, is developed on a spreadsheet, which is capable of simulating scenarios to address issues of increasing traditional energy-demand caused by population growth, sustainable supply capacity of the existing energy resources, potential for development of new and renewable energy resources, technology. This paper is divided into two parts: general energy issues and the modelling approach, and the application of this approach to Nepal in the context of fuelwood-supply sustainability.

The manufacturing industry has undergone numerous revolutions over the years, with a unanimous acceptance of the greater benefits of being sustainable. The present industrial wave—Industry 4.0—by using its enabling technologies and principles holds great potential to develop sustainable manufacturing paradigms which require balancing out the three fundamental elements —products, processes, and systems. Yet, numerous stakeholders, including industrial policy and decision makers, remain oblivious of such potential and requirements. Thus, this bibliometric study is aimed at presenting an overview of the broad field of research on the convergence of sustainable manufacturing and Industry 4.0 under the umbrella of “Sustainable Manufacturing 4.0”, which has yet to be developed. It includes the dissemination of original findings on pathways and practices of Industry 4.0 applied to the development of sustainable manufacturing, contributing a bibliometric structure of the literature on the aforementioned convergence to reveal how Industry 4.0 could be used to shift the manufacturing sector to a more sustainable-based state. An initial research agenda for this emerging area has accordingly been presented, which may pave the way for having a futuristic view on Sustainable Manufacturing 5.0 in the next industrial wave, i.e., Industry 5.0.

PurposeThe purpose of this paper is to outline a comprehensive picture of the coverage of various certification schemes and sustainability principles relating to the entire value‐added chain of biomass and bioenergy and comparing them accordingly.Design/methodology/approachA tri‐dimensional approach (sustainability issues; technical biomass conversion routes; physical trade flows) was developed for testing the coverage of various sustainability dimensions in different phases of the value‐added chain with the chosen certification schemes and sustainability principles.FindingsUsing the tri‐dimensional approach, a comparison of the chosen schemes and principles demonstrated that the application of existing schemes and the development of new ones have placed a major emphasis on the primary production of biomass. Economic and social dimensions related to biofuels and bioenergy processing and trade were either emphasised less or they were covered inadequately. In view of this, the schemes sometimes seem to ignore that the utilisation of renewable energy as such guarantee no positive or neutral climate impact and may not be economically sustainable, especially when bioenergy can often be more expensive than energy generated from fossil energy sources.Originality/valueThe analysis showed that the tri‐dimensional model is an applicable framework that could facilitate policy makers to formulate policies that comprehensively take into consideration the various sustainability dimensions throughout the entire value‐added chain, now and in the future. It can be applied to the future outlining and completion of certification schemes and sustainability principles for biomass and bioenergy, as well as in the testing of their applicability in the implementation.