• Energy Research
• Open Access close
• Restricted close
• Embargo close
• DE close
• ZENODO close

This deliverable includes the methodology in EnergyPROSPECTS for an in-depth study of energy citizenship. It features the criteria used for selecting the cases for indepth study, the list of cases selected for in-depth study as well as key research foci and empirical research questions.

Due to the increasing demand for higher efficiencies of centrifugal compressors, numerical optimization methods are becoming more and more relevant in the design process. To identify the beneficial features of a numerical optimized compressor design, this paper analyses the influence of arbitrary blade surfaces on the loss generation in a transonic centrifugal compressor. The paper therefore focuses on an analysis of the secondary flow development within the impeller blade passages. To do this, steady simulations were performed on both a baseline and an optimized blade design. Two distinct design features of the optimized compressor stage were identified, which lead to a more homogenous impeller exit flow and thus to an increase in total-to-static efficiency of 1.76% points: the positive lean in the near-tip region and the positive blade curvature in the rear part of the optimized impeller. Furthermore, through extensive experimental investigations conducted on a large scale test rig it has been possible to prove the particular impeller outflow characteristics of the baseline compressor stage.

Environmental and intrinsic factors interact to determine energy requirements in vertebrates. Glucocorticoid hormones (GCs) are key mediators of this interaction, as they fluctuate with energetic demands and regulate physiological and behavioral responses to environmental challenges. While a great body of research has focused on GC variation among individuals, the mechanisms driving GC variation across species and at broad spatial scales remain largely unexplored. Here, we adopted a macrophysiological approach to investigate the environmental factors and life-history traits driving variation in baseline GCs across lizard species. We tested three hypotheses: (1) If GCs increase with body temperature to meet higher metabolic demand, we expect an association between average baseline GCs and the mean species’ body temperature in the field (GC-temperature dependence hypothesis); (2) If GCs mediate behavioral responses to avoid thermal extremes, we expect that individuals frequently exposed to extreme conditions exhibit higher baseline GC levels (Behavioral thermoregulation hypothesis); (3) If GCs increase to support higher energy demands in active foragers during their period of activity, we expect that active foraging species have higher baseline GCs than sit-and-wait foragers, and that GC levels increase in relation to the duration of daily activity windows (Activity hypothesis). We used biophysical models to calculate operative temperatures and the activity patterns of lizards in sun-exposed and shaded microenvironments. Then, we tested the association between baseline GCs, body temperature, operative temperatures, foraging mode, and activity windows across 37 lizard species, using data from HormoneBase. Our comparative analyses showed that variation in baseline GCs was primarily related to the mean field body temperature and foraging mode, with higher baseline GCs in active foragers with higher body temperatures. Our results suggest that body temperature and foraging mode drive GC variation through their effects on energy requirements across lizard species.

AbstractCurrently, Sb2Se3 thin films receive considerable research interest as a solar cell absorber material. When completed into a device stack, the major bottleneck for further device improvement is the open‐circuit voltage, which is the focus of the work presented here. Polycrystalline thin‐film Sb2Se3 absorbers and solar cells are prepared in substrate configuration and the dominant recombination path is studied using photoluminescence spectroscopy and temperature‐dependent current–voltage characteristics. It is found that a post‐deposition annealing after the CdS buffer layer deposition can effectively remove interface recombination since the activation energy of the dominant recombination path becomes equal to the bandgap of the Sb2Se3 absorber. The increased activation energy is accompanied by an increased photoluminescence yield, that is, reduced non‐radiative recombination. Finished Sb2Se3 solar cell devices reach open‐circuit voltages as high as 485 mV. Contrarily, the short‐circuit current density of these devices is limiting the efficiency after the post‐deposition annealing. It is shown that atomic layer‐deposited intermediate buffer layers such as TiO2 or Sb2S3 can pave the way for overcoming this limitation.

<p>Commonly used host rock reservoirs for Enhanced Geothermal Systems (EGS) are composed of granite, as they display highly conductive and sustainable fracture networks after stimulation. However, considering the large amount of metamorphic rocks in Europe’s underground, these rock types may also show a large potential to extract geothermal energy from the subsurface. Within the framework of the European Union’s Horizon 2020 initiative ‘MEET (Multi-Sites EGS Demonstration)’, we are conducting fracture permeability experiments at elevated confining pressures, p<sub>c</sub>, temperatures, T, and differential stresses, </p>

AbstractImproving the long-term stability of perovskite solar cells is critical to the deployment of this technology. Despite the great emphasis laid on stability-related investigations, publications lack consistency in experimental procedures and parameters reported. It is therefore challenging to reproduce and compare results and thereby develop a deep understanding of degradation mechanisms. Here, we report a consensus between researchers in the field on procedures for testing perovskite solar cell stability, which are based on the International Summit on Organic Photovoltaic Stability (ISOS) protocols. We propose additional procedures to account for properties specific to PSCs such as ion redistribution under electric fields, reversible degradation and to distinguish ambient-induced degradation from other stress factors. These protocols are not intended as a replacement of the existing qualification standards, but rather they aim to unify the stability assessment and to understand failure modes. Finally, we identify key procedural information which we suggest reporting in publications to improve reproducibility and enable large data set analysis.