• Energy Research
• 7. Clean energy close
• 6. Clean water close
• 1. No poverty close
• AU close
• CN close
• EC close
• English close

Points out that sustainability as such does not provide a clearcut guide to policy. First one has to decide what is to be sustained. If this is agreed, it must be in an operational from. However, difficulties may still emerge since opinions may differ about how to achieve. This is illustrated by differences in the views of economists about how sustainable development is to be achieved. Orthodox economists stress the importance of the accumulation of man-made capital to achieve this end whereas neo-Malthusians stress the importance of conserving natural resource and environmental capital. Both take an anthropocentric point of view. For political reasons the neo-Malthusian has had little support but it may eventually turn out to be correct. Economics is concerned with reducing economic scarcity and economists have traditionally suggested four main ways of doing this of which economic growth is one. However, neo-Malthusian economists believe that this may not be a sustainable strategy – it may result in future poverty. It should be noted that economic systems are embedded in social and natural systems and depend on these. Economic sustainability depends on the sustainability of these other systems. So from this point of view, it is just one of several bottom lines. Values must be considered in relation to sustainability. Economics is completely anthropocentric in its approach. Therefore, economic approaches to conservation and sustainability can be at odds with the values of deep ecologists or those willing to accord rights to other sentient beings or ecosystems independent of human wishes, or those who want to make use of value judgments other than those based on the measuring rod of money. Consequently economics evaluation is sometimes ineffective in resolving social conflict, including conflict about what should be sustained. As a rule economics alone should not be the final arbiter of social decisions. It is a part (often an important part) of the social evaluation process but not the bottom line, or just one of many lines.

Points out that sustainability as such does not provide a clearcut guide to policy. First one has to decide what is to be sustained. If this is agreed, it must be in an operational from. However, difficulties may still emerge since opinions may differ about how to achieve. This is illustrated by differences in the views of economists about how sustainable development is to be achieved. Orthodox economists stress the importance of the accumulation of man-made capital to achieve this end whereas neo-Malthusians stress the importance of conserving natural resource and environmental capital. Both take an anthropocentric point of view. For political reasons the neo-Malthusian has had little support but it may eventually turn out to be correct. Economics is concerned with reducing economic scarcity and economists have traditionally suggested four main ways of doing this of which economic growth is one. However, neo-Malthusian economists believe that this may not be a sustainable strategy – it may result in future poverty. It should be noted that economic systems are embedded in social and natural systems and depend on these. Economic sustainability depends on the sustainability of these other systems. So from this point of view, it is just one of several bottom lines. Values must be considered in relation to sustainability. Economics is completely anthropocentric in its approach. Therefore, economic approaches to conservation and sustainability can be at odds with the values of deep ecologists or those willing to accord rights to other sentient beings or ecosystems independent of human wishes, or those who want to make use of value judgments other than those based on the measuring rod of money. Consequently economics evaluation is sometimes ineffective in resolving social conflict, including conflict about what should be sustained. As a rule economics alone should not be the final arbiter of social decisions. It is a part (often an important part) of the social evaluation process but not the bottom line, or just one of many lines.

Exhaust hoods are commonly used to capture all emissions from stationary combustion systems that are open to the environment, such as residential heaters or stoves. For experimental purposes, emissions are sampled at one, or more, discrete locations downstream in the exhaust duct. Point-wise measurements in the duct are often taken with the assumption that the emissions are homogeneously distributed across the duct cross-section, because the flow is turbulent and therefore believed to be thoroughly mixed. However, the length of such systems is rarely sufficient to ensure fully-developed flow, and the actual homogeneity is seldom assessed. In the present work the mixing within the duct is investigated by simulating the emissions distribution within various hood and duct configurations. The simulations include a straight duct with and without baffles and two different exhaust hood configurations, namely at the Stove Testing Lab at Lawrence Berkeley National Laboratory (LBNL) and at the University of Adelaide that meet standard requirements. The air flow in the ducts was simulated using Reynolds-averaged (RANS) turbulence modelling, with carbon monoxide (CO) as a representative combustion product, injected at three locations in the straight duct and two locations (centre and side) in the exhaust hoods. Simulations predict that, in isolation, neither a straight duct without baffles, nor a hood with a 90° elbow followed by a straight duct without baffles, provide sufficient mixing to achieve a near uniform distribution of CO at the sampling locations. However, simulations show that adequate mixing of dilution air and CO is achieved with baffles-induced flow detachment and recirculation, not from turbulent mixing in the straight section of the duct itself. The simulations also suggest that elbows, baffles, expansions or other geometrical features are needed to induce thorough mixing. For example, in the Stove Testing Lab at LBNL, flow disturbance is induced by an expansion into a larger diameter straight duct immediately downstream of the hood and the 90° elbow. Although these two systems demonstrate sufficient mixing of CO within the exhaust, the RANS simulations in this study suggest that other systems relying solely on mixing within a specified duct length (viz. 8–12 diameters) may not be sufficient. Refereed/Peer-reviewed

Exhaust hoods are commonly used to capture all emissions from stationary combustion systems that are open to the environment, such as residential heaters or stoves. For experimental purposes, emissions are sampled at one, or more, discrete locations downstream in the exhaust duct. Point-wise measurements in the duct are often taken with the assumption that the emissions are homogeneously distributed across the duct cross-section, because the flow is turbulent and therefore believed to be thoroughly mixed. However, the length of such systems is rarely sufficient to ensure fully-developed flow, and the actual homogeneity is seldom assessed. In the present work the mixing within the duct is investigated by simulating the emissions distribution within various hood and duct configurations. The simulations include a straight duct with and without baffles and two different exhaust hood configurations, namely at the Stove Testing Lab at Lawrence Berkeley National Laboratory (LBNL) and at the University of Adelaide that meet standard requirements. The air flow in the ducts was simulated using Reynolds-averaged (RANS) turbulence modelling, with carbon monoxide (CO) as a representative combustion product, injected at three locations in the straight duct and two locations (centre and side) in the exhaust hoods. Simulations predict that, in isolation, neither a straight duct without baffles, nor a hood with a 90° elbow followed by a straight duct without baffles, provide sufficient mixing to achieve a near uniform distribution of CO at the sampling locations. However, simulations show that adequate mixing of dilution air and CO is achieved with baffles-induced flow detachment and recirculation, not from turbulent mixing in the straight section of the duct itself. The simulations also suggest that elbows, baffles, expansions or other geometrical features are needed to induce thorough mixing. For example, in the Stove Testing Lab at LBNL, flow disturbance is induced by an expansion into a larger diameter straight duct immediately downstream of the hood and the 90° elbow. Although these two systems demonstrate sufficient mixing of CO within the exhaust, the RANS simulations in this study suggest that other systems relying solely on mixing within a specified duct length (viz. 8–12 diameters) may not be sufficient. Refereed/Peer-reviewed

Of all the renewable resources, solar energy has the greatest potential for endingour reliance on fossil fuels. The solar energy that reaches the earth’s surface is 10,000 times the total energy consumption of the planet at any given time and yet we harness only 0.1% of this, mostly as solar-thermal energy. The major limitations of solar energy conversion processes are cost and storage. Strategies for addressing these issues have focused on advanced designs and new materials. Nanomaterials- materials with high surface-to-volume ratios, play a crucial role in the future of this industry. The work of this thesis involved a novel design for a cost-effective, water-splitting system that produces hydrogen - a storable fuel. The system designwas comprised of nanomaterials assembled on a microparticle. Thesis (PhD)--University of South Australia, 2016. Includes bibliographical references.

Of all the renewable resources, solar energy has the greatest potential for endingour reliance on fossil fuels. The solar energy that reaches the earth’s surface is 10,000 times the total energy consumption of the planet at any given time and yet we harness only 0.1% of this, mostly as solar-thermal energy. The major limitations of solar energy conversion processes are cost and storage. Strategies for addressing these issues have focused on advanced designs and new materials. Nanomaterials- materials with high surface-to-volume ratios, play a crucial role in the future of this industry. The work of this thesis involved a novel design for a cost-effective, water-splitting system that produces hydrogen - a storable fuel. The system designwas comprised of nanomaterials assembled on a microparticle. Thesis (PhD)--University of South Australia, 2016. Includes bibliographical references.

In the Meyer-Burger labs, pilot production of its proprietary 6''-Heterojunction (HJT) cells has been conducted on full-scale production tools (Roth & Rau Helia PECVD & Helia PVD). Overall, close to 10.000 cells have been manufactured with efficiencies up to 21,1%. From theses HJT cells, 60-cell modules have been produced. Temperature coefficient measurements of both cells and modules have been conducted by independent institutes, resulting in outstanding -0,20%/K and -0,22%/K, respectively. The modules have been deployed on an outdoor test field in Mid-European climate conditions for over 1 year. The results demonstrate the durability of the HJT modules and comparison with standard crystalline modules show an increase of energy yield of up to 7% on sunny days already in spring time. Under hot climate conditions in southern regions this increase is supposed to be even higher, making HJT modules extremely suitable for southern climates and low LCOE´s. 28th European Photovoltaic Solar Energy Conference and Exhibition; 1887-1889

In the Meyer-Burger labs, pilot production of its proprietary 6''-Heterojunction (HJT) cells has been conducted on full-scale production tools (Roth & Rau Helia PECVD & Helia PVD). Overall, close to 10.000 cells have been manufactured with efficiencies up to 21,1%. From theses HJT cells, 60-cell modules have been produced. Temperature coefficient measurements of both cells and modules have been conducted by independent institutes, resulting in outstanding -0,20%/K and -0,22%/K, respectively. The modules have been deployed on an outdoor test field in Mid-European climate conditions for over 1 year. The results demonstrate the durability of the HJT modules and comparison with standard crystalline modules show an increase of energy yield of up to 7% on sunny days already in spring time. Under hot climate conditions in southern regions this increase is supposed to be even higher, making HJT modules extremely suitable for southern climates and low LCOE´s. 28th European Photovoltaic Solar Energy Conference and Exhibition; 1887-1889

Building materials have played a more and more important role in saving building energy since the central government of China set higher standards and requirements for new-constructed and retrofit buildings after 2005. Glazing units, especially energy-saving units including LOW-E coated glazing units and PVB laminated glass, are utilized nation-wide. This paper employs energy simulation to analyze the energy-saving effects of different glazing units in residential buildings in the city of Guangzhou, as an example of hot-humid climate in China. It appeals that the PVB laminated glass can refuse 44 % solar radiation to enter rooms and reduce 40 % of the shading coefficient comparing to clear glass. Meanwhile, in the aspects of operation and design of the HVAC system, 28 % of cooling load, 21 % of installed capacity and 8.6 % of full-load operation time can be saved.

Building materials have played a more and more important role in saving building energy since the central government of China set higher standards and requirements for new-constructed and retrofit buildings after 2005. Glazing units, especially energy-saving units including LOW-E coated glazing units and PVB laminated glass, are utilized nation-wide. This paper employs energy simulation to analyze the energy-saving effects of different glazing units in residential buildings in the city of Guangzhou, as an example of hot-humid climate in China. It appeals that the PVB laminated glass can refuse 44 % solar radiation to enter rooms and reduce 40 % of the shading coefficient comparing to clear glass. Meanwhile, in the aspects of operation and design of the HVAC system, 28 % of cooling load, 21 % of installed capacity and 8.6 % of full-load operation time can be saved.