• Energy Research
• 7. Clean energy close
• 13. Climate action close
• ES close
• CA close
• Applied Energy close

The unpredictable nature of renewable energies is drawing attention to lithium-ion batteries. In order to make full utilization of these batteries, some research works are focused on the management of existing systems, while others propose sizing techniques based on business models. However, in order to optimise the global system, a comprehensive methodology that considers both battery sizing and management at the same time is needed. This paper proposes a new optimisation algorithm based on a combination of dynamic programming and a region elimination technique that makes it possible to address both problems at the same time. This is of great interest, since the optimal size of the storage system depends on the management strategy and, in turn, the design of this strategy needs to take account of the battery size. The method is applied to a real installation consisting of a 100 kWp rooftop photovoltaic plant and a Li-ion battery system connected to a grid with variable electricity price. Results show that, unlike conventional optimisation methods, the proposed algorithm reaches an optimised energy dispatch plan that leads to a higher net present value. Finally, the tool is used to provide a sensitivity analysis that identifies key informative variables for decision makers The authors would like to acknowledge the support of the Spanish State Research Agency and FEDER-UE under grants DPI2016-80641-R and DPI2016-80642-R; of Government of Navarra through research project PI038 INTEGRA-RENOVABLES; and the FPU Program of the Spanish Ministry of Education, Culture and Sport (FPU13/00542).

Abstract This paper presents a parametric analysis for a medium to large size (290–500 MW th receiver thermal power) central receiver plant considering the present market trends. The analysis is divided in 4 steps: • Size and location analysis: for a medium to large size central receiver power plant, three turbine power and three different locations that are involved in the development of power tower plants, have been analyzed to assess the impact over the design characteristics of the solar field and receiver sub-systems and over the levelized electricity cost. • Technology analysis: as commercial power tower plants in operation today are mainly using steam and molten nitrate salts, the present analysis compares the two main technologies, without thermal energy storage to evaluate both under similar design conditions. • Storage analysis: thermal energy storage increases the value of electricity produced and the plant capacity factor for both technologies (steam and molten nitrate salts). For this reason, the analysis shows for each optimized solar field and receiver thermal power, the optimum combination of turbine power and thermal energy storage that minimizes the levelized electricity cost, for both technologies. • Component’s cost analysis: market trends are focused on the specific cost reduction by means of larger plant size and through an improved economy of scale. As a result, and based on baseline cost parameters widely accepted in solar industry, an analysis over the specific costs of major components on the electricity cost has been carried out, to lead where the research and development efforts should be made.

The increase in installed wind power has brought a number of Grid Code areas into focus. The area of fault ride-through capability is one with serious implications for system security and thus has an impact on the allowed wind energy penetration in the network. There are several wind turbine models that can be used to study the effects of voltage dips and the corresponding wind turbine responses but these models need to be validated by comparing their results with the data obtained during field tests. This paper presents the design of a voltage dip generator that can be used to test wind turbines up to 5 MW and 20 kV. This system is able to adjust voltage dip depth and duration to the standards defined in different countries and also the fault impedance seen by the grid in order not to disturb its operation during the tests. Simulation results are validated using experimental data obtained at a laboratory-scale prototype (400 V, 90 kW). Finally, the actual 5 MW system and the results obtained during field tests are presented.

Abstract Based on an extensive dataset containing aggregated hourly energy consumption readings of residents during March 2011 and October 2012 in South Ontario, Canada, this paper estimates the energy consumption of circulating pumps of residential swimming pools (CPRSP) non-intrusively, and quantifies the impact of CPRSP on the power system. The main challenges are that, first, widely used non-intrusive appliance load monitoring (NIALM) methods are not applicable to this work, due to the low sampling rate and the lack of the energy consumption pattern of CPRSP; second, temperature-based building energy disaggregation methods are not suitable for this work, as they highly depend on the accurate base load estimation and predefined parameters. To overcome these issues, in this paper, first it is found that, during the pool season, for homes with and without swimming pools, the ratio between their base loads is approximately equal to the ratio between their temperature-dependent energy consumptions, then a novel weighted difference change-point (WDCP) model has been proposed. The advantages of the WDCP model are that, on one hand, it doesn’t depend on the base load estimation and predefined parameters; on the other hand, it has no requirement on the data sampling rate and the prior information of energy consumption patterns of CPRSP. Based on the WDCP model it is shown that, the average hourly energy consumption of CPRSP is 0.7425 kW, and the minimum and the maximum hourly energy consumptions are 0.5274 kW at 9:00 and 0.9612 kW at 17:00, respectively. At the peak hour 19:00, July 21, 2011, CPRSP contributes 20.36% energy consumption of homes with swimming pools, as well as 8.48% peak load of all neighborhoods. As a result, the peak load could be reduced by 8.48% if all CPRSP are stopped during the peak hour.

An ever more environmentally conscious society demands the use of green, sustainable and high-efficiency renewable energy resources. However, large-scale energy storage remains a challenge for a deep penetration of power produced from renewables into the grid. The Calcium-Looping (CaL) process, based on the reversible carbonation/calcination of CaO, is a promising technology for thermochemical energy storage (TCES) in Concentrated Solar Power (CSP) plants. Natural limestone to be used as CaO precursor is cheap, non-toxic and abundant. Nevertheless, recent works have shown that carbonation of CaO derived limestone at optimum conditions for TCES is limited by pore-plugging, which leads to severe deactivation for large enough particles to be employed in practice. In our work, we have synthesized inexpensive CaO/SiO composites by means of a biotemplate method using rice husk as support. The morphological and compositional features of the biomorphic materials synthesized help improve the CaO multicycle activity under optimum CSP storage conditions and for particles sufficiently large to be managed in practical processes. Peer Reviewed

Abstract A new open-loop solar tracking system for a small-scale linear Fresnel reflector with three movements has been designed, fabricated, and simulated. The control system of the solar tracker is governed by a Raspberry Pi together with other auxiliary devices which include a Global Positioning System. The electronic control system consists of a master controller (Raspberry pi 3), 4 slave microcontrollers (Arduino), Global Positioning System module, thermocouples, laser sensors, transversal positioning sensors, and longitudinal positioning sensors. It also allows the communication between these microcontrollers based on long range wireless solutions (XBee). All the electronic circuits have been designed and constructed. The solar tracking system uses offline data. The software has been designed and developed to track the sun path using astronomical equations. In this way, the solar tracking system is able to position itself automatically using the solar position algorithm and the Global Positioning System with an accuracy of ±0.006°. The solar tracking system can be deployed automatically at any location on the Earth. The total cost of the implemented solar tracking system has been calculated. The system performance, in terms of the tracking error, annual energy, energy-to-area ratio and levelized cost of energy has been evaluated. Tracking errors smaller than 0.06 (°) are acceptable (they cause power losses smaller than 1%), whereas errors larger than 0.36 (°) start being noticeable (power losses greater than 3%). The proposed new tracking system gives 16.64% more energy, a 78.46% higher energy-to-area ratio, and a 4.62% less levelized cost of energy that the classic tracking system with one movement used in large-scale linear Fresnel reflectors.

Abstract The effects of the operating conditions on the performance of metal hydride hydrogen storage tanks are complicated and need detailed investigations for further optimization. In this study, a mathematical model is developed to understand the effects of the various operating conditions on the hydrogen absorption processes in a LaNi 5 metal hydride tank. The numerical results indicate that the quickest charging process occurs within the first 20 s, and the quickest charging rate and duration are mainly affected by the charging pressure and initial temperature, respectively. The effect of cooling level on this process is insignificant. For both the short-time charging (2 min) and long-time charging, the hydrogen fueling performance is significantly affected by the cooling level (the heat transfer coefficient and surrounding temperature) and charging pressure. In order to ensure sufficiently quick hydrogen charging, the charging pressure needs to be kept enough higher than the equilibrium pressure, and due to the fast heating of the metal hydride, the influence of the initial temperature is less significant than the cooling condition. The general distributions of the absorbed hydrogen fraction and temperature are similar under the different operating conditions.

The thermal performance of a novel solar air collector with metal corrugated packing in the buildings of cold regions is studied in this paper. Mathematical models are developed to investigate the thermal performance of the collector and the results are verified by experiments. The hydraulic analysis is conducted experimentally to study the pressure drops of the air flows in the corrugated packing. Effects of the structural and operating parameters, such as the collector width, height, specific surface area and solar radiation intensity, ambient air temperature, air inlet temperature and velocity are studied to optimize the thermal performance of the collector. Comparisons are conducted among the metal corrugated packing solar air collector, the unglazed transpired solar collector, the glazed transpired solar collector and the packed bed solar collector with iron chips. The results indicate that the metal corrugated packing solar air collector is more appropriate to be used in the rural buildings of cold regions for its advantages of large heat transfer area, high heat transfer coefficient and good economic performance.