• Energy Research
• Restricted close
• ES close
• GB close
• MY close

Artículos en revistas Multi-terminal High Voltage Direct Current (HVDC) using Voltage Source Converters (VSC-HVDC) is a promising technology which provides flexible control of active and reactive power and facilitates remote renewable energy integration, above all using long cables. This paper analyses an active power control strategy for multi-terminal VSC-HVDC systems tailored to enhance transient stability of hybrid AC/DC grids. The proposed strategy controls each VSC using frequency measurements of all terminals. Its performance is compared to a strategy in which each VSC is controlled using only local frequency measurements of the AC side, proving that the proposed strategy shows better performance, even taking into account reasonable communication delays. The paper also shows that the proposed strategy generally gives similar results to those obtained when each VSC is controlled using the speed of the centre of inertia (COI). The speed of the COI is a more comprehensive and richer figure than the one proposed in this paper but it is also much more complex to obtain. Simulation results with PSS/E of a test system have been used to illustrate the comparisons and the main contributions of the proposal. info:eu-repo/semantics/publishedVersion

Thermal performance of SS-PCM composites, simulating building envelope conditions, is difficult to asset with traditional laboratory equipment. However, in this work, the evaluation of three SS-PCM based on eutectic fatty acid mixtures of capric-myristic (CA/MA), lauric-myristic (LA/MA) and palmitic-stearic (PA/SA) was accomplished by a testing setup that allows to test samples in steady-state and dynamic conditions. Moreover, a SS-PCM-based acrylic plaster was evaluated as a fiber cement siding finish. The obtained values were used to calculate the thermal transmittance (U-value), heat storage capacity, and thermal inertia parameters under a simulated diurnal cycle. Results showed that the use of phase change materials in powder form increase thermal lag between 148% and 180% and present a decrement factor <0.2. Furthermore, building envelopes as fiber cement siding with a SS-PCM-based acrylic plaster coating decreased 20.8% the indoor temperature, increase 67.26% the thermal lag and decrease 9% of the decrement factor. The authors are pleased to acknowledge the financial assistance of the “Ministerio de Ciencia, Tecnología e Innovación-MINCIENCIAS” through the PhD grant 758-2016-Contract 036–2016, Universidad de Antioquia and Sumicol S.A.S. The work is partially funded by the Ministerio de Ciencia, Innovación y Universidades de España (RTI2018-093849-B-C31—MCIU/AEI/FEDER, UE) and by the Ministerio de Ciencia, Innovación y Universidades—Agencia Estatal de Investigación (AEI) (RED2018-102431-T). This work is partially supported by ICREA under the ICREA Academia programme. Dr. Cabeza would like to thank the Catalan Government for the quality accreditation given to her research group GREiA (2017 SGR 1537). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.

Artículos en revistas Units within a control area, participating in the secondary frequency control, are usually spinning generating units already connected to the network and operating outside their range of optimal performance. This paper deals with an alternative method of providing secondary frequency control called rapid-start (RS). It consists in assigning a regulation band to several offline units (RS units) which are capable of being started and connected rapidly, therefore allowing the online units to function more closely to their nominal power. RS units have commonly been used for peaking generation and for tertiary control reserve, and have been rarely used for secondary control reserve. As RS operation may have economic benefits, since it allows for better dispatch of the other units in the control area, an appropriate algorithm to start up an RS unit needs to be developed. This paper proposes a machine learning based system (MLBS) to be employed in the decision to start up an RS unit while being used to provide secondary frequency control. The decision-making procedure is carried out by a decision tree. The building and implementation of the RS machine learning based system is illustrated for a secondary frequency control zone within the Spanish power system. info:eu-repo/semantics/publishedVersion

In this study, air concentrations of BaP in two different seasons (winter 2015 and summer 2016) and BaP levels in ground vegetation from Tarragona County were used as control simulations performed with the WRF-CHIMERE air quality modelling system, in order to reproduce the incidence of that hazardous chemical in air and soils. The CTM was validated for the present climatology, showing a good ability to represent air and soil concentrations of BaP over the target domain (petrochemical, chemical, urban and background sites), particularly in the winter. Then, the variation of the BaP concentrations in air and soils were simulated for the time series 1996-2015 and for the climate change scenario RCP8.5 (2031-2050). While an increase is projected for the levels in air, particularly in chemical and remote sites where the variation can go up to 10%, in terms of soil deposition the findings are the opposite, with an evident decrease in soil BaP concentrations, particularly for background sites. Finally, a potential health effect of BaP for the local population (lung cancer) was assessed. Although according to the projections the EU threshold for BaP atmospheric incidence (1 ng m-3) will not be reached by 2050, there will be an increase in the life-time risk of lung cancer, particularly in the most populated areas within the simulation domain.

Artículos en revistas In this paper we propose a methodology to approximate closed loop capacity equilibria using only open loop capacity equilibrium models. In the closed loop model, generation companies choose capacities that maximize their individual profit in the first stage while the second stage represents the conjecturedprice- response market equilibrium. In the open loop model, firms simultaneously choose capacities and quantities to maximize their individual profit, while each firm conjectures a price response to its output decisions. The closed loop equilibrium model is an equilibrium problem with equilibrium constraints, which belongs to a class of problems that is very hard to solve. The open loop equilibrium model is much easier to solve, however, it is also less realistic. With the approximation scheme proposed in this paper, we are able to solve the closed loop model reasonably well when market behavior is closer to oligopoly than to perfect competition by smartly employing open loop models which reduces the computational time by two orders of magnitude. We achieve this by transforming the open loop equilibrium problem into an equivalent convex quadratic optimization problem which can be solved efficiently. Finally, a case study is presented in order to validate the proposed approximation scheme. info:eu-repo/semantics/publishedVersion

Searching suitable panchromatic QD sensitizers for expanding the light-harvesting range, accelerating charge separation, and retarding charge recombination is an effective way to improve power conversion efficiency (PCE) of quantum-dot-sensitized solar cells (QDSCs). One possible way to obtain a wide absorption range is to use the exciplex state of a type-II core/shell-structured QDs. In addition, this system could also provide a fast charge separation and low charge-recombination rate. Herein, we report on using a CdTe/CdSe type-II core/shell QD sensitizer with an absorption range extending into the infrared region because of its exciplex state, which is covalently linked to TiO2 mesoporous electrodes by dropping a bifunctional linker molecule mercaptopropionic acid (MPA)-capped QD aqueous solution onto the film electrode. High loading and a uniform distribution of QD sensitizer throughout the film electrode thickness have been confirmed by energy dispersive X-ray (EDX) elemental mapping. The accelerated electron injection and retarded charge-recombination pathway in the built CdTe/CdSe QD cells in comparison with reference CdSe QD-based cells have been confirmed by impedance spectroscopy, fluorescence decay, and intensity-modulated photocurrent/photovoltage spectroscopy (IMPS/IMVS) analysis. With the combination of the high QD loading and intrinsically superior optoelectronic properties of type-II core/shell QD (wide absorption range, fast charge separation, and slow charge recombination), the resulting CdTe/CdSe QD-based regenerative sandwich solar cells exhibit a record PCE of 6.76% (J(sc) = 19.59 mA cm(-2), V(oc) = 0.606 V, and FF = 0.569) with a mask around the active film under a full 1 sun illumination (simulated AM 1.5), which is the highest reported to date for liquid-junction QDSCs.

Artículos en revistas Large frequency deviations due to a number of disturbances are frequent in small isolated power systems. The maximum frequency deviation in the system is limited to prevent other generator tripping. It is important to have an accurate model to calculate it, both for system planning and operation. A new simplified model to calculate the maximum frequency deviation when either a generator or load-related disturbance occurs in these systems is presented. This model takes into account the response of governor- prime mover even when different technologies are present in the power system. Model parameters can be easily obtained from either more complex models or from test records. Simulation results for an actual power system aimed at checking the model accuracy are presented. High accuracy is obtained while computation time is reduced due to the simplicity of the model. info:eu-repo/semantics/publishedVersion

With the concept of climate services rapidly climbing research and research-funding agendas worldwide, the time is ripe for a debate about the objectives, scope and content of such services.

This deliverable presents the detailed design of the SunDial concentrators for two case-studies: AMTP, in Iasi (Romania), and MAN, in Corinth (Greece). The design of the concentrator is different for both cases due to two reasons: first, the location in Iasi has a high latitude that implies the need of a design specifically suited to a lower mean sun altitude; second, in order to increase the performance of the concentrator for high latitudes a two-axis tracking system has been selected, which leads to a completely different layout of mirrors and receivers within the rotating platform compared to low latitudes, where one-axis tracking is used. The size of the platforms, which resulted from the analytical studies presented in deliverables D3.1 and D3.2, is 8-9 m per collector side, too large be shipped as a whole module. Therefore, the design of the concentrators has sought a system modularity that enables an easy transportation and installation. The design of the concentrators can be divided into three sub-systems: the rotating platform, the mirrors, and the receivers. A CAD software is used in order to design all of them. The connection between the sub-systems is included in the design. Images resulting from the CAD design are used in order to describe the design concept of each subsystem, whereas the final drawings, which are the main outcome of the deliverable, are presented in the annexes. Also, the CAD design is used to provide the elements inventory of the concentrators, including the materials selected and the manufacturing process used.

Abstract In recent years, the overall energy consumption is increasing significantly and the energy consumption in the building sector represents over 30% of the global ones in developed countries. Thermal energy storage (TES) using phase change materials (PCM), which are materials able to store high amounts of energy as latent heat, is suggested as a possible solution to decrease the energy consumption. The authors of this paper developed materials able to encapsulate/stabilize PCM in addition to isolate an industrial residue from the steel recycling process: electrical arc furnace dust (EAFD). This waste is a hazardous dust, and when it is combined with a polymeric matrix produce dense sheet materials suitable for multilayered constructive systems. In this paper the physical, mechanical, thermal and acoustical characterization of two new materials with EAFD and PCM in a polymeric matrix for constructive system is presented. The results are compared with those obtained for one commercial dense sheet material available in the market, Texsound commercialized by TEXSA (Spain). The new dense sheet materials developed in this paper have similar acoustic properties compared to the results obtained for the commercial material and are competitive with it, even better because the new material incorporates PCM which increases the thermal inertia of final constructive system.