• Energy Research
• 7. Clean energy close
• 13. Climate action close
• 11. Sustainability close
• 6. Clean water close
• IT close
• ES close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

This article describes an innovative method for measuring lighting levels and other lighting parameters through the use of aerial imagery of towns and cities. Combined with electricity consumption data from smart electricity meters, it was possible to measure the energy efficiency of public lighting installations. The results of this study also confirmed that lighting measurements, installation material, luminaire position, and electricity consumption data can be easily integrated into geographic information systems (GIS). The main advantage of this new methodology is that it provides information about lighting installations in large areas in less time than more conventional procedures. It is thus a more effective way of obtaining the data required to calculate the energy efficiency of lighting levels and electricity consumption. There is even the possibility of generating street lighting maps that provide local administrations with up-to-date information regarding the status of public lighting installations in their city. In this way, modifications or improvements can be made to achieve greater energy savings and, if necessary, to correct the distribution or configuration of public lighting systems to make them more efficient and sustainable. This research studied levels of street lighting and calculated the energy efficiency in various streets of Deifontes (Granada), through the use of aerial imagery.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

It is crucial to reduce the energy penalties related to CO2 capture processes if CCS is to be implemented at industrial scale. In this context, gas-solid sorption has become a relevant technology. The absence of large amounts of water when using dry solid sorbents and their high heat capacity reduce the energy requirements in the gas-solid sorption CO2 capture process. Depending on the sorbent composition, the gas-solid sorption process carries out at high or low temperatures. High temperature sorbents allow the utilization of waste energy while energy requirements in low temperature processes will be less demanding. This study is focused on the assessment and comparison of the final energy penalty of low-temperature (amine impregnated alumina-based solid particles) and high-temperature solid sorbents capture process (calcium oxide).

Changes in the main weather features are becoming perceivable in Italy. In the last years, the average temperature and the intensity of rainstorms are increasing. Such phenomena could lead to changes in the earth-atmosphere interaction. Accounting for the high vulnerability of the Italian territory, an obvious consequence would concern the effects on the hydro-geological hazards, including landslides and floods. As a matter of fact, the higher frequency of high magnitude flood and landslide events represent an alarm bell. It is necessary to explore with all available instruments the consequences of the potential climate changes. Since quantitative predictions are not possible, the only way to run is depicting rational scenarios for the most vulnerable contexts adopting a multidisciplinary approach. Based on projections of potential climate changes in the 21st century, the report examines their potential impact in the context of the Italian peninsula. After a general overview about typical slope responses to weather changes, some quantitative scenarios have been depicted for representative geomorphological contexts. The last part of the paper examines changes in the expected risk, based on the characteristics of the Italian territory and its vulnerability, looking at the initiatives to undertake for its mitigation.

Hydrochar, carbon-rich material produced during the thermochemical processing of biomass, is receiving increased attention due to its potential value as soil amendment. It can increase agroforestry systems’ productivity through direct and indirect effects on growth and soil quality. Hydrochar may also directly help mitigate climate change by sequestering stable carbon compounds in the soil and perhaps indirectly through increased C uptake by trees. In this research, we aim to evaluate how the application of hydrochar produced by two feedstock types, Cynara cardunculus L. (Hc) residuals and sewage sludge (Hs), and in two different doses (3 and 6 kg m−2) could improve the growth and water use efficiency of Populus alba L., a fast-growing tree species largely used in agroforestry as bioenergy crops and in C sequestration. We considered five plants per treatment, and we measured apical growth, secondary growth, leaf area and intrinsic water use efficiency in each plant for the whole growing season from February to October 2022. Our results highlighted that hydrochar applications stimulate the growth and water use efficiency of plants and that the double dose (6 kg m−2) of both hydrochars, and particularly Hc, had positive effects on plant performance, especially during extremely hot periods. Indeed, the year 2022 was characterized by a heat wave during the summer period, and this condition allowed us to evaluate how plants, growing in soils amended with hydrochar, could perform under climate extremes. Our findings showed that the control plants experienced severe damage in terms of dried stems and dried leaves during summer 2022, while hydrochar applications reduced these effects.

AbstractThis report illustrates the experimental data associated with solar overheating. The experimental data has validated an analytical model which allows for the study of the influences a primary circuit's design has on the overheating of the solar tank.Secondly, the report includes a study of the stagnation in a solar facility. The evolution of the temperature in the hydraulic circuit by means of its measurement at 30 different points, together with the data of the pressure and flow, allow for the real behavior of the solar installation in stagnation conditions to be investigated.Finally, the study shows the measurements obtained on a solar thermal installation located in Alicante (southern Spain). Every installation has been monitored for several months and the main temperatures and pressures around the solar circuit have been noted. The measurements and their processing have allowed for the detection of overheating and stagnation problems in real operating conditions.

Model projections show that production of high-value products from microalgae could be profitable nowadays and commodities will become profitable within 10 years.