• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• 12. Responsible consumption close
• 6. Clean water close
• BR close
• ES close
• PT close

The influence of ethanol on the degradation kinetics of linear alkyl benzene sulfonate (LAS) and organic matter was investigated using batch experiments with different initial LAS concentrations (8.3 mg L-1 to 66.9 mg L-1) and biomass immobilized on sand. Data were fitted with a substrate inhibition model. Concentrations of 2.4 mg LAS L-1 and 18.9 mg LAS L-1 (without and with ethanol) provided the maximum LAS utilization rate by the biomass (Sbm). For LAS degradation, ethanol addition favored a lower decrease in the specific substrate utilization rate (robs), even at the LAS concentration usually reported as inhibitory (> 14.4 mg L-1). For organic matter degradation, robs was higher with ethanol. Higher biomass differentiation was observed at higher LAS concentrations. With ethanol, microbial selection occurred at LAS concentrations near Sbm. At higher LAS concentrations, the dominance and diversity values did not change significantly with ethanol, whereas without ethanol, their behaviors were irregular.

This paper reports the real-time behavior of the leakage current flowing on glass-type insulator strings of a 230-kV substation tower during washing. Monitoring of two insulator strings in the tower is achieved by use of a pair of optical-fiber sensors that detect samples of the leakage current waveforms and transmit those samples to a processing module via an optical link. It is observed that leakage current during washing may reach high peak levels, and the effectiveness of the washing can be inferred by the degree of leakage current after drying of the insulator strings. Direct monitoring of the leakage current can thus be used as an important guideline for proper washing procedures during this type of intervention as well as for determining the effectiveness of the procedure.

It is now recognized that analytical chemistry must also be a target for green principles, in particular chromatographic methods which typically use relatively large volumes of hazardous organic solvents. More generally, high performance liquid chromatography (HPLC) is employed routinely for quality control of complex mixtures in various industries. Acetonitrile and methanol are the most commonly used organic solvents in HPLC, but they generate an impact on the environment and can have a negative effect on the health of analysts. Ethanol offers an exciting alternative as a less toxic, biodegradable solvent for HPLC. In this work we demonstrate that replacement of acetonitrile with ethanol as the organic modifier for HPLC can be achieved without significantly compromising analytical performance. This general approach is demonstrated through the specific example analysis of a complex plant extract. A benchmark method employing acetonitrile for the analysis of Bidens pilosa extract was statistically optimized using the Green Chromatographic Fingerprinting Response (GCFR) which includes factors relating to separation performance and environmental parameters. Methods employing ethanol at 30 and 80°C were developed and compared with the reference method regarding their performance of separation (GCFR) as well as by a new metric, Comprehensive Metric to Compare Liquid Chromatography Methods (CM). The fingerprint with ethanol at 80°C was similar to or better than that with MeCN according to GCFR and CM. This demonstrates that temperature may be used to replace harmful solvents with greener ones in HPLC, including for solvents with significantly different physiochemical properties and without loss in separation performance. This work offers a general approach for the chromatographic analysis of complex samples without compromising green analytical chemistry principles.

Abstract This paper aims to investigate sustainable waste management solutions for the city of Rio de Janeiro in Brazil, based on a life cycle approach. The Life Cycle Assessment (LCA) was performed by using the LCA-IWM methodology. The model was adapted to the Brazilian solid waste context and to the local characteristics, including waste composition, electricity mix and regulations. The annual amount of waste generated was the functional unit adopted. Eight municipal solid waste management strategies were evaluated. Scenarios including mixed waste collection and source separated collection as well as materials recovery and energy from waste were investigated. Scenarios were ranked based on the LCA results. Sensitivity analysis was carried out by varying the electricity mix. The results indicate that the current situation of municipal solid waste (MSW) in Rio de Janeiro presents the worst performance in terms of aggregated environmental burdens, indicating the urgency for implement new strategies toward a more environmentally friendly and sustainable MSW management system. It is noted that the better LCA performances were obtained in scenarios with high separately collection rates. Among them, the scenario based on recyclables recovery and anaerobic digestion shows to be a promising strategy to improve environmental sustainability. Sensitivity analysis demonstrates that the ranking of scenarios was not affected by changes in the electricity mix. From the results, the investment in source separated waste collection and materials recovery is the most environmentally friendly MSW strategy for Rio de Janeiro. In addition, scenarios with an emphasis in materials recovery presented higher environmental benefits than the alternatives focused on energy generation.

We investigated how a community of microbial decomposers adapted to a reference site responds to a sudden decrease in the water quality. For that, we assessed the activity and diversity of fungi and bacteria on decomposing leaves that were transplanted from a reference (E1) to a polluted site (E2), and results were compared to those from decomposing leaves either at E1 or E2. The two sites had contrasting concentrations of organic and inorganic nutrients and heavy metals in the stream water. At E2, leaf decomposition rates, fungal biomass, and sporulation were reduced, while bacterial biomass was stimulated. Fungal diversity was four times lower at the polluted site. The structure of fungal community on leaves decomposing at E2 significantly differed from that decomposing at E1, as indicated by the principal response curves analysis. Articulospora tetracladia, Anguillospora filiformis, and Lunulospora curvula were dominant species on leaves decomposing at E1 and were the most negatively affected by the transfer to the polluted site. The transfer of leaves colonized at the reference site to the polluted site reduced fungal diversity and sporulation but not fungal biomass and leaf decomposition. Overall, results suggest that the high diversity on leaves from the upstream site might have mitigated the impact of anthropogenic stress on microbial decomposition of leaves transplanted to the polluted site.

Ammonia increases buffer capacity of methanogenic medium in mesophilic anaerobic reactor thus increasing the stability of anaerobic digestion process. Optimal ammonia concentration ensures sufficient buffer capacity while not inhibiting the process. It was found out in this paper that this optimum depends on the quality of anaerobic sludge under investigation. The optimal concentrations for methanogens were 2.1, 2.6 and 3.1 g/L of ammonia nitrogen in dependence on inoculum origin. High ammonia nitrogen concentration (4.0 g/L) inhibited methane production, while low ammonia nitrogen concentration (0.5 g/L) caused low methane yield, loss of biomass (as VSS) and loss of the aceticlastic methanogenic activity. It was found out that negative effect of low ammonia nitrogen concentration on biomass is caused not only by low buffer capacity but also by insufficiency of nitrogen as nutrient. It was also found out that anaerobic sludge with higher ammonia nitrogen concentration (4.2 g/L) tolerates even concentration of volatile fatty acids (160 mmol/L) which causes inhibition of the process with low ammonia nitrogen concentration (0.2 g/L).

AbstractBrazilian countryside has well‐defined dry seasons that are mainly characterized by low relative humidity. The warm, dry air provides a thermal cooling effect when it interacts with wet porous structures (psychrometric effect). Depending on temperature conditions and relative humidity, it is possible to achieve up to 18.0 K reduction in the temperature of the structure, caused by water evaporation. Thus, the objective of this study was to propose and numerically investigate a low cost and sustainable air conditioning system by combining the potential of warm, dry air and characteristics of the flow within cyclones covered with thin wet cotton fabric. A validated mathematical model was developed, and the numerical results indicate that the cyclonic‐psychrometric system can provide up to 7.0 K reduction in a 20.0 m2 room on a warm day (305.0 K) with low relative humidity (20.0%). Energy balances and technical estimates showed that the electric power consumed by the proposed system would represent only 19.8% of the power required by a conventional 18,000 Btu air conditioner to promote the same reduction of temperature. This energy‐saving would have a direct and positive impact on the budget of users, especially those with low income and that live in dry regions.

This paper describes anaerobic thermophilic sludge digestion (55 °C) in a continuously stirred tank reactor (CSTR) on a pilot-plant scale (150 L). The experimental protocol was defined to examine the effect of the increase in the organic loading rate on the efficiency of the digester and to report on its steady-state performance. The reactor was subjected to a programme of steady-state operation over a range of solids retention times (SRTs) of 75, 40, 27, 20 and 15 days and organic loading rates (OLR) in the range 0.4–2.2 kg VS/(m3 day). The digester was fed with raw sludge (containing approximately 35 kg/m3 volatile solids (VS)) once daily during the 75-day SRT period, twice daily during the 40-day SRT period and three times a day during the 27-, 20- and 15-day SRT periods. The reactor was initially operated with an organic loading rate of 0.4 kg VS/(m3 day) and an SRT of 75 days. The volatile solids removal efficiency in the reactor was found to be 73%, while the volumetric methane production rate produced in the digester reached 0.02 m3/(m3 day). Over a 338-day operating period, an OLR of 2.2 kg VS/(m3 day) was achieved with 49.1% VS removal efficiency in the pilot sludge digester, at which time the volumetric methane production rate content of biogas produced in the digester reached 0.4 m3/(m3 day). The chemical oxygen demand (COD) mass balance obtained indicated that COD used for methane generation increased when the SRT was decreased or when the influent organic loading rate was increased. This implies that the amount of COD used in the anabolism route decreased with SRT due the microbial population becoming adapted to new operational conditions and more COD being used to generate methane.

One of the major goals of engine designers is the reduction of fuel consumption and pollutant emissions while keeping or even improving engine performance. In recent years, different technical issues have been investigated and incorporated into internal combustion engines in order to fulfill these requirements. Most are related to the combustion process since it is responsible for both fuel consumption and pollutant emissions. Additionally, the most critical operating points for an engine are both the starting and the warming up periods (the time the engine takes to reach its nominal temperature, generally between 80°C and 90°C), since at these points fuel consumption and pollutant emissions are larger than at any other points. Thus, reducing the warm-up period can be crucial to fulfill new demands and regulations. This period depends strongly on the engine cooling system and the different strategies used to control and regulate coolant flow and temperature. In the present work, the influences of different engine cooling system configurations on the warm-up period of a Diesel engine are studied. The first part of the work focuses on the modeling of a baseline engine cooling system and the tests performed to adjust and validate the model. Once the model was validated, different modifications of the engine coolant system were simulated. From the modelled results, the most favourable condition was selected in order to check on the test bench the reduction achieved in engine warm-up time and to quantify the benefits obtained in terms of engine fuel consumption and pollutant emissions under the New European Driving Cycle (NEDC). The results show that one of the selected configurations reduced the warm-up period by approximately 159 s when compared with the baseline configuration. As a consequence, important reductions in fuel consumption and pollutant emissions (HC and CO) were obtained.