• Energy Research
• Restricted close
• Open Source close
• Embargo close
• other engineering and technologies close
• ES close
• PT close

[EN] The objective of this article is to compare the behaviour of the most representative domestic hot water systems (DHW) in single-family buildings. The study evaluates the energy consumption, equivalent CO2 emissions and cost for each system over a 15-year life period. This analysis is carried out in four cli- matic zones across Europe to observe the influence of climatic conditions on the results. The four climatic zones are located in the cities of Athens, Madrid, London and Berlin. The analysed systems are: a) natural gas-fired instantaneous water heaters, b) electric storage water heater, c) solar thermal system with gas- fired instantaneous, d) solar thermal system with electric storage water heater, e) air-source heat pump, f) photovoltaic system with electric storage water heater, and g) photovoltaic system with air-source heat pump. This range of technologies covers the most likely solutions to be implemented across domestic buildings in Europe.The heat pump system (HPWH) with PV considering self-consumption shows the lowest environmen- tal impact in all zones, but is not an attractive investment in the coldest zones due to lower natural gas prices. Thermal solar systems have a high purchase and maintenance costs which do not compensate their energy savings. The PV HPWH system has a greater reduction of emissions and a lower cost than HPWH across a 15-year life. The gas boiler system has the lowest cost in a 15-year period in the coldest areas, despite having a greater environmental impact than the heat pump.(c) 2023 Elsevier B.V. All rights reserved.

In this paper a new simulation environment for a virtual laboratory to educational proposes is presented. The Logisim platform was adopted as the base digital simulation tool, since it has a modular implementation in Java. All the hardware devices used in the laboratory course was designed as components accessible by the simulation tool, and integrated as a library. Moreover, this new library allows the user to access an external interface. This work was motivated by the needed to achieve better learning times on co-design projects, based on hardware and software implementations, and to reduce the laboratory time, decreasing the operational costs of engineer teaching. Furthermore, the use of virtual laboratories in educational environments allows the students to perform functional tests, before they went to a real laboratory. Moreover, these functional tests allow to speed-up the learning when a problem based approach methodology is considered.

Abstract Thermal energy storage (TES) systems are growing to a relevant role in solar cooling applications. Hence, high energy density is a desirable property of the TES system. Phase change materials (PCM) helps to increase this characteristic. A high temperature pilot plant able to test different types of TES systems and materials was designed and built at the University of Lleida (Spain). This pilot plant is composed mainly of three parts: heating system, cooling system, and different storage tanks. Two identical storage tanks based on the shell-and-tubes heat exchanger, one of them including 196 squared fins in the bundle of the tubes and the other without, were experimentally tested. Hydroquinone was selected as the storage material, having a latent heat of 205 kJ/kg and a phase change temperature between 168 and 173 °C. The aim of this paper is to test experimentally, and compare the average effectiveness of the TES systems analyzed using PCM for solar cooling and refrigeration applications. It was found out that for the same tank configurations (shell-and-tubes) even changing drastically the dimensions of the tank or the number and the diameter of the tubes, the average effectiveness curve proposed in the literature fits well with the results showed here.

AbstractReview: 105 refs.

The building and construction sector is a large contributor to anthropogenic greenhouse gas emissions and consumes vast natural resources. Improvements in this sector are of fundamental importance for national and global targets to combat climate change. In this context, vertical greenery systems (VGS) in buildings have become popular in urban areas to restore green space in cities and be an adaptation strategy for challenges such as climate change. However, only a small amount of knowledge is available on the different VGS environmental impacts. This paper discusses a comparative life cycle assessment (LCA) between a building with green walls, a building with green facades and a reference building without any greenery system in the continental Mediterranean climate. This life cycle assessment is carried according to ISO 14040/44 using ReCiPe and GWP indicators. Moreover, this study fills this gap by thoroughly tracking and quantifying all impacts in all phases of the building life cycle related to the manufacturing and construction stage, maintenance, use stage (operational energy use experimentally tested), and final disposal. The adopted functional unit is the square meter of the facade. Results showed that the operational stage had the highest impact contributing by up to 90% of the total environmental impacts during its 50 years life cycle. Moreover, when considering VGS, there is an annual reduction of about 1% in the environmental burdens. However, in summer, the reduction is almost 50%. Finally, if the use stage is excluded, the manufacturing and the maintenance stage are the most significant contributors, especially in the green wall system.

Artículos en revistas In this paper we apply stochastic dual dynamic programming decomposition to a nonconvex multistage stochastic hydrothermal model where the nonlinear water head effects on production and the nonlinear dependence between the reservoir head and the reservoir volume are modeled. The nonconvex constraints that represent the production function of a hydro plant are approximated by McCormick envelopes. These constraints are split into smaller regions and the McCormick envelopes are used for each region. We use binary variables for this disjunctive programming approach and solve the problem with a decomposition method. We resort to a variant of the L-shaped method for solving the MIP subproblem with binary variables at any stage inside the stochastic dual dynamic programming algorithm. A realistic large-scale case study is presented. info:eu-repo/semantics/publishedVersion

Artículos en revistas Liberalization policies, the challenges of integrating distributed generation resources, and the recent flattening of electricity demand due to the economic crisis and technological change have led to lower returns for European electricity suppliers. Innovative and sustainable business models are needed to serve electricity customers while reflecting the operational needs of the system and maintaining supplier financial viability. This paper describes a novel model of Integrated Energy Services that encompasses distributed generation (DG) and demand response (DR) resources for industrial customers. We further reflect on some of the market opportunities and regulatory drivers for the development of similar schemes across Europe. info:eu-repo/semantics/publishedVersion

Industry is a fundamental sector that allows mass production to support a large population. As population grows, many industries produce large amounts of industrial effluents with different pollutants, that must be removed at the industrial wastewater treatment plants, with the consequent production of large amounts of sludge. The present study was conducted to identify and evaluate different sludge treatment/valorisation methodologies, being given priority to the valorisation in detriment of the elimination operations, like incineration or landfill. Therefore, sludges from the wastewater treatment plant of a resin industry, after dehydration operation by a press, were submitted to several valorisation methodologies, such as: application in anaerobic digestion aiming the production of biogas and allowing energy recovery, use in the preparation of adsorbents for the treatment of industrial wastewater, use as cement replacement in mortar production, and application of heterogeneous catalysts to produce biodiesel. The results revealed that all methodologies can be applied as sludge recovery. However, it is possible to conclude that the most promising industrial sludge treatment/recovery hypothesis is anaerobic co-digestion followed by the production of heterogeneous catalysts for biodiesel production.