• Energy Research
• ES close

Abstract Thermal energy storage systems for both heat and cold are necessary for many industrial processes. High energy density and high power capacity are desirable properties of the storage. The use of latent heat increases the energy density of the storage tank with high temperature control close to the melting point. Tube in PCM tank is a very promising system that provides high packing factor. This work presents an experimental study of a PCM tank for cold storage applications. Two different configurations and different flow rates of the heat transfer fluid were studied. The effectiveness of the PCM storage system was defined as that of a heat exchanger. The results showed that the heat exchange effectiveness of the system did not vary with time, decreased with increasing flow rate and increased with increasing heat transfer area. The effectiveness was experimentally determined to only be a function of the ratio m ˙ /A. This equation was found to be adequately be used to design a PCM storage system, and a case study is presented. It was shown that the tube in tank design together with a low temperature PCM is suitable as a thermal storage facility for cold storage.

Considerable effort has been devoted to the characterization of thermal properties of the different types of materials that can be used as thermal energy storage (TES) media, but scarce literature exists concerning the materials to manufacture the tanks that can be used to contain these storage media. One of the main concerns when selecting the most suitable material for these tanks is its resistance to corrosion due to molten salts that constitute the TES system. Dynamic gravimetric analysis is a newly proposed method for the study of corrosion on metals, which optimizes the standard procedure described by ASTM G1-03. The new technique avoids the direct handling of samples, so more accurate values can be obtained. In this work, the resistance to corrosion of AISI 316 stainless steel samples in contact with commercial grade molten salts of the Li2CO3-Na2CO3-K2CO3 system, at 600 °C for different exposure times, has been determined by using this new methodology. The results show that the initial corrosion rate is lower at higher amounts of lithium carbonate present in the molten salts mixture.

In the present paper, an experimental study is carried out to evaluate the effect of the dynamic melting concept in a cylindrical shell-and-tube heat exchanger using water as the phase change material (PCM) and a potassium formate/water solution as the heat transfer fluid (HTF). The dynamic melting concept is a new heat transfer enhancement technique which consists of recirculating the liquid PCM during the melting process with a pump and thus increasing the overall heat transfer coefficient as a result of the dominance of the forced convection. The HTF flow rate was kept constant at 1 l/min and four different PCM flow rates of 0, 0.5, 1 and 2 l/min were tested. Results from the experimental analysis showed enhancements up to 65.3% on the melting period, up to 56.4% on the effectiveness, and 66% on the heat transfer rates when the PCM flow rate was twice the HTF flow rate. From these experiments, it can be concluded that dynamic melting is an effective technique for enhancing heat transfer during melting of PCM. The authors acknowledge the South Australian Department of State Development who have funded this research through the Premier’s Research Industry Fund - International Research Grant Program (IRGP 33). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047). The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123).

Thermally activated building systems (TABS) can work as thermal energy storage (TES) systems, which are useful in shifting the energy use of space cooling and heating in buildings. The present study analyses and optimizes simple deterministic control concepts for radiant wall supplied by a heat pump for cooling purposes. First, the "solar" concept was studied, which was focused on exploiting the output of a photovoltaic (PV) array. Secondly, a "peak load shifting" concept exploiting the low electricity cost and high heat pump energy efficiency during night periods was evaluated. The results showed that the "solar" concept saved between 57% and 95% in comparison to a conventional control in different PV installed capacities. Moreover, the optimized "peak load shifting" concept had lower operation cost than the conventional control with most of the PV configurations proposed. Therefore, the study showed that the investment in the PV array was fully harnessed only with specific controls. Furthermore, the "solar" control concepts were found to help achieving the goals of net-zero energy buildings by maximising self-consumption of renewable energies in the building, as well as reducing the total imported/exported energy. The authors acknowledge the South Australian Department of State Development who have funded this research through the Premier’s Research Industry Fund – International Research Grant Program (IRGP 33). The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 712949 (TECNIOspring PLUS) and from the Agency for Business Competitiveness of the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537) and the city hall of Puigverd de Lleida.

Abstract Numerical modelling is commonly used to design, analyse and optimise tube-in-tank phase change thermal energy storage systems with fins. A new simplified two dimensional mathematical model, based on the effectiveness-number of transfer units technique, has been developed to characterise tube-in-tank phase change material systems, with radial round fins. The model applies an empirically derived P factor which defines the proportion of the heat flow which is parallel and isothermal. This P factor was determined using a validated computational fluid dynamics model. This method can be used to design and optimise tube-in-tank salt based phase change thermal storage units with finned tubes.

The intermittency of renewable energy systems remains one of the major hurdles preventing a large scale uptake of these technologies and concentrated solar power (CSP) systems are no different. However, CSP has the benefit of being able to store excess heat using thermal energy storage (TES). For the uptake of CSP with TES it must be demonstrated that the technology is both economically as well as environmentally feasible. This paper aims to investigate the economic and environmental impact of several TES options that are available for CSP systems. The investigated systems include an encapsulated phase change material (PCM) system, a coil-in-tank PCM system and a liquid sodium TES system. The economic impact in the current study refers to the capital cost (CAPEX) of each system including the tank, storage material, encapsulation cost (if applicable) and allowances for construction and engineering. The environmental impact of each system is accounted by calculating the embodied energy of each of the system components. Each storage system will be required to store a comparable amount of energy so that reliable conclusions can be drawn. The results from this analysis conclude that the encapsulated PCM (EPCM) and coil-in-tank system represent an embodied energy of roughly one third of the corresponding state-of-the-art two-tank molten salt system. Furthermore, the EPCM and coil-in-tank systems result in CAPEX reductions of 50% and 25% over the current state-of-the-art two-tank molten salt system. The liquid sodium system was found to result in higher embodied energy and CAPEX than any previously studied TES system. Finally, the advantages and disadvantages of each system was discussed and compared to previous literature. This research was performed as part of the Australian Solar Thermal Research Initiative (ASTRI), a project supported by the Australian Government, through the Australian Renewable Energy Agency (ARENA). The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R and ENE2015-64117-C5-2-R). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).