• Energy Research
• Closed Access close
• Restricted close
• Embargo close
• other engineering and technologies close
• ES close

Abstract AP1000® Generation III+ reactor bases its safety concept on passive systems, differently from the previous Generation II reactors. This fact has led the approximations and methodologies previously used for modeling active safety systems to be reviewed and adapted to simulate the physics of passive systems. Diverse studies about the AP1000 containment have demonstrated the difficulty to correctly model the occurring phenomenology. In this paper, an integral AP1000 3D containment GOTHIC model is presented, including the Passive Containment Cooling System (PCCS). The model includes the compartments inside and outside the metallic containment liner that influence the thermal–hydraulic behavior. The model is tested against a Large Break Loss of Coolant Accident (LBLOCA) to assess its thermal–hydraulic performance, assuming a PCS tank malfunction, what is a conservative hypothesis. The pressure and temperature evolution predicted by the 3D containment model is analyzed and compared with a single node Lumped Parameters model, allowing to evaluate some preliminary benefits of 3D modeling for containment safety analysis. The 3D containment model allows to predict the thermal evolution in each containment compartment capturing the heterogeneity of this phenomenon, with higher resolution than the lumped parameters models traditionally used in this kind of analyses. It allows to observe the thermohydraulic conditions locally at any time during the transient.

Previous work carried out for the last eight years resulted in the proposal of a complete system of dimensionless groups in order to represent the performance of different kinematic Stirling engine configurations. When looking for experimental support for the proposed model, some differences between the performances of several prototypes were observed. In this paper an equation is introduced to be applied to all known kinematic engines and to their whole range of performance. The coefficients appearing in this equation can be computed from temperature and geometrical dimensionless ratios and from experimental measurements at the maximum indicated power operating point. The meaning of those coefficients is interpreted and their usefulness to provide an engine performance overview is shown. The quasi-static simulation and the characteristic Mach number at the maximum indicated power operating point appear to be interesting criteria in order to evaluate the performance of prototypes.

Artículos en revistas It is shown how a standard nonlinear programming approach can be applied to solve a sophisticated version of the static optimal mix problem in generation planning. The model presented includes technical minima of thermal capacity, detailed operating models of storage-hydro and pumped-hydro units, a realistic model of capital costs for hydro plants, operating reserve and minimum demand constraints, and capacity already in existence. The model formulation is in a format that can be directly handled by the well-known MINOS code and can be efficiently solved. The use of a general-purpose nonlinear optimization program results in a great flexibility, making it possible to modify the model formulation easily or to adapt it to the characteristics of a particular electric system. A realistic application to the Spanish generation system is presented info:eu-repo/semantics/publishedVersion

The aim of the present work was to develop 3D discrete element models capable of simulating the observed flow of glass beads (simple glass spheres) and maize grains (represented as a combination of spheres) during their discharge from a small model silo. A preliminary model for each material was constructed based on values for variables measured in the laboratory or taken from the literature. The ability of the models to predict the flow of these materials was then tested by comparing their results with observed discharge flows. Three variables were recorded for this: the mean bulk density at the end of the filling phase, the discharge rate and the flow pattern. The comparison of the results for the last of these variables required the discharge process be filmed using a high speed camera in order to more easily recognise the details of the flow. The preliminary model for the glass beads made very reasonable predictions, but that for the maize grains required calibration. This involved modifying the values of the friction properties of the material until a model capable of making acceptable predictions was obtained. The results obtained highlighted the influence of friction properties on the characteristics of the discharge flow. Finally, some of the numerical results provided by the models were analysed in order to describe the flow characteristics and the behaviour of the discharge rate in more detail.

Abstract The combined production of electricity, heat and cold by a polygeneration system connected to a district heating and cooling network can provide high energy utilization efficiency. The inherent complexity of simultaneous production of different services and the high variability in the energy demand make combined cooling and heating systems performance highly dependent on the operational strategy. In this paper, an operational optimization method based on the moving average of real-time measurements of energy demands and ambient conditions is proposed. Real energy demand data from a district heating and cooling network close to Barcelona, Spain, are used to test the method. A complex polygeneration system is considered, consisting of an internal combustion engine, a double-effect absorption chiller, an electric chiller, a boiler and a cooling tower. A detailed modelling of the system is provided, considering partial load behavior of the components and ambient conditions effects. Results of the real-time optimal management are discussed and compared to traditional operational strategies and to the ideal optimal management achievable with perfectly accurate forecast of energy demands. Moreover, the optimal width of the window adopted for the moving average of real-time data is identified.

Abstract In this work, Co/Cu nanowires are fabricated by pulsed electrodeposition from a single bath solution containing both Co and Cu ions. Alternate Co and Cu layers are deposited into the nanopores of track etched polycarbonate templates. Although the feasibility of this process is generally recognized, some important issues such as process reproducibility and how structural defects affect the nanowires arrays’ sensing performances are still open; conditions necessary to turn a this made system into a magnetic field sensor. The present work aims at pushing forward knowledge concerning the nanowires fabrication and defining the best growth parameters; in particular, a tight control of the growth process parameters such as single metal deposition potentials and single cycle deposition durations have been carried out for nanowires of 80 nm diameter and correlated to the system magneto-electric response.

Abstract For Solid Oxide Fuel Cells (SOFCs) to become an economically attractive energy conversion technology, suitable materials and structures which enable operation at lower temperatures, while retaining high cell performance, must be developed. Recently, the perovskite-type La 0.6 Ca 0.4 Fe 0.8 Ni 0.2 O 3 oxide has shown potential as an intermediate temperature SOFC cathode. An equivalent circuit describing the cathode polarization resistances was constructed from analyzing impedance spectra recorded at different temperatures in oxygen. A competitive electrode polarization resistance is reported for this oxygen electrode using a Ce 0.8 Gd 0.2 O 1.9 electrolyte, determined by impedance spectroscopy studies of symmetrical cells sintered at 800 °C and 1000 °C. Scanning electron microscopy (SEM) studies of the symmetrical cells revealed the absence of any reaction layer between cathode and electrolyte, and a porous electrode microstructure even when sintered at a temperature of only 800 °C. The performance of this cathode shows favorable oxygen reduction reaction (ORR) properties potentially making it an excellent choice for IT-SOFC application.