• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• EU close
• AT close

Wind turbine gearbox operates under a wide array of highly fluctuating and dynamic load conditions caused by the stochastic nature of wind and operational wind turbine controls. Micropitting damage is one of failure modes commonly observed in wind turbine gearboxes. This article investigates gear micropitting of high-speed stage gears of a wind turbine gearbox operating under nominal and varying load and speed conditions. Based on the ISO standard of gear micropitting (ISO/TR 15144-1:2010) and considering the operating load and speed conditions, a theoretical study is carried out to assess the risk of gear micropitting by determining the contact stress, sliding parameter, local contact temperature and lubricant film thickness along the line of action of gear tooth contact. The non-uniform distributions of temperature and lubricant film thickness over the tooth flank are observed due to the conditions of torque and rotational speed variations and sliding contact along the gear tooth flanks. The lubricant film thickness varies along the tooth flank and is at the lowest when the tip of the driving gear engages with the root of the driven gear. The lubricant film thickness increases with the increase of rotational speed and decreases as torque and sliding increase. It can be concluded that micropitting is most likely to initiate at the addendum of driving gear and the dedendum of driven gear. The lowest film thickness occurs when the torque is high and the rotational speed is at the lowest which may cause direct tooth surface contact. At the low-torque condition, the varying rotational speed condition may cause a considerable variation of lubricant film thickness thus interrupting the lubrication which may result in micropitting.

This article examines the porosity of national borders using the examples of two nuclear facilities at Gorleben and Morsleben located at the West German municipality in the state of Lower Saxony as well as the former Börde district of Saxony-Anhalt (former East Germany). Gorleben and Morsleben became known for their final nuclear waste repositories located directly at the German-German border. Debates and protests surrounding the facilities began in the 1970s and continued after the wall came down. Since opponents had to deal with two different political systems, protests differed in their duration, effect, and methods, even though the border as such was not the problem since West Germans were allowed into the GDR. Transboundary relations were much rather limited by the dictatorial regime on the one side, by the absence of anti-nuclear groups in the GDR until the mid-1980s, and by sufficient coalition partners for West German activists in their own country. Since the disclosure of environmental data by the East German government and the Chernobyl accident a few years later, transboundary relations increased and activists interconnected in many ways. With their protest they indicated that even if the border was a fact, concerns of people in both states transcended it and that borderlands are often characterized by relationality and entanglement.

Combining electrochemical and biological catalysis creates more suitable and efficient routes for the processing of renewable resources, such as CO2 and biomass.

Long tubes with small internal diameter find increasing applications in indirect concentrated solar receivers using an Upflow Bubbling Fluidized Bed of Geldart-A powders as heat carrier. Although successfully demonstrated for tubes of 0.5 to 1 m length, longer tubes are required to increase the solar energy capture efficiency and capacity. The fluidization phenomena differ with the tube length, and freely bubbling fluidization will be transformed into slugging, thus hampering the heat transfer. The behavior of Geldart-A powders in tall tubes of small I.D. has not been extensively studied. The research experimentally investigated the different fluidization modes in a 4 m long tube, and demonstrated the occurrence of freely bubbling at the bottom section of the bed, and slugging from a bed depth in excess of about 1.25 m. Slug characteristics (frequency, length, velocity) were measured and correlated. The results were used to validate 3D numerical simulations based on an Euler-Euler approach in the NEPTUNE_CFD code applied to a fine mesh of 15,000,000 cells. A positive match between experimental and simulation results concerning frequency and velocity of large bubble structures was obtained. The effect of mesh refinement on the slugging behavior prediction was discussed.

We jointly select the fronthaul links and optimize the transmit precoding matrices for maximizing the energy efficiency (EE) of a multiuser multiple-input multiple-output-aided distributed antenna system. The fronthaul link’s power consumption is taken into consideration, which is assumed to be proportional to the number of active fronthaul links quantified by using indicator functions. Both the rate requirements and the power constraints of the remote access units are considered. Under realistic power constraints, some of the users cannot be admitted. Hence, we formulate a two-stage optimization problem. In Stage I, a novel user selection method is proposed for determining the maximum number of admitted users. In Stage II, we deal with the EE optimization problem. First, the indicator function is approximated by a smooth concave logarithmic function. Second, a triple-layer iterative algorithm is proposed for solving the approximated EE optimization problem, which is proved to converge to the Karush–Kuhn–Tucker conditions of the smoothened EE optimization problem. To further reduce the complexity, a single-layer iterative algorithm is conceived, which guarantees convergence. Our simulation results show that the proposed user selection algorithm approaches the performance of the exhaustive search method. Finally, the proposed algorithms are capable of achieving an order of magnitude higher EE than its conventional counterpart operating without considering link selection.

An algorithm to optimise the number of solar panels and battery size to meet the water demands of an installation has been developed. The algorithm adjusts for seasonal changes in energy use and production in a pressurized irrigation network and production in an off-grid solar panel system. By using this algorithm, we aim to create an efficient and sustainable irrigation system by reducing the infrastructure and reliance on the power grid. This method can enhance irrigation systems in far-off regions, strengthen their endurance, and promote sustainable energy in farming and water administration. This work was supported by the project “Hi-Edu Carbon”"Erasmus Plus Programme, Key Action KA22021, action type (2021-1-SK01-KA220-HED-000023274.

This study presents the results of the biomass pyrolysis process focusing on biochar production and its potential energetic (as solid fuel) and material (as adsorbent) applications. Three kinds of biomass waste were investigated: wheat straw, spent coffee grounds, and brewery grains. The pyrolysis process was carried out under nitrogen atmosphere at 400 and 500 °C (residence time of 20 min). A significant increase in the carbon content was observed in the biochars, e.g., from 45% to 73% (at 400 °C) and 77% (at 500 °C) for spent coffee grounds. In addition, the structure and morphology were investigated using scanning electron microscopy. Thermal properties were studied using a simultaneous thermal analysis under an oxidising atmosphere. The chemical activation was completed using KOH. The sorption properties of the obtained biochars were tested using chromium ion (Cr3+) adsorption from liquid solution. The specific surface area and average pore diameter of each sample were determined using the BET method. Finally, it was found that selected biochars can be applied as adsorbent or a fuel. In detail, brewery grains-activated carbon had the highest surface area, wheat straw-activated carbon adsorbed the highest amount of Cr3+, and wheat straw chars presented the best combustion properties.