• Energy Research
• Open Access close
• Closed Access close
• engineering and technology close
• DE close
• EU close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

We present the architecture and design of the IANOS scheduling framework. The goal of the new Grid scheduling system is to provide a general job submission framework allowing optimal positioning and scheduling of HPCN applications. The scheduling algorithms used to calculate best-suited resources are based on an objective cost function that exploits information on the parameterization of applications and resources. This standard-based, interoperable scheduling framework comprises four general web services and three modules. The middleware is complemented with one client and one admin console. The implementation is based on proposed Grid and Web services standards (WSRF, WS-Agreement, JSDL, and GLUE). It is agnostic to a specific Grid middleware. The beta version of IANOS has been tested and integrated with UNICORE. The validation of IANOS is in progress by running different types of HPCN applications on a large-scale Grid testbed.

We present the architecture and design of the IANOS scheduling framework. The goal of the new Grid scheduling system is to provide a general job submission framework allowing optimal positioning and scheduling of HPCN applications. The scheduling algorithms used to calculate best-suited resources are based on an objective cost function that exploits information on the parameterization of applications and resources. This standard-based, interoperable scheduling framework comprises four general web services and three modules. The middleware is complemented with one client and one admin console. The implementation is based on proposed Grid and Web services standards (WSRF, WS-Agreement, JSDL, and GLUE). It is agnostic to a specific Grid middleware. The beta version of IANOS has been tested and integrated with UNICORE. The validation of IANOS is in progress by running different types of HPCN applications on a large-scale Grid testbed.