• Energy Research
• Closed Access close
• AU close
• IT close
• FR close
• Renewable Energy close

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

Abstract Probability density functions (PDFs) are normally used to describe wind speed distribution for the proper selection of wind turbines in a given location. The identification of a suitable PDF is fundamental for accurately assessing the wind energy potential and designing the wind farms. To achieve this objective, the use of a mixture of two truncated normal distributions (MTTND), defined for v ≥ 0 and obtained by linearly combining two normal distributions with different means and variances, is proposed in this work for the representation of the wind speed PDF. The distribution is a function of five parameters, does not require a high computational burden and allows the representation of wind calm hours (v = 0). The use of the MTTND allows an accurate estimation to be obtained of the experimental discrete distribution of the probability density and cumulative probability, and the characteristic statistical quantities used to estimate the available energy and the performance indicators in the selection of both the site and wind turbine. The validity of the use of the MTTND was verified by comparison with the most widespread PDFs in the scientific literature: Weibull, Rayleigh, lognormal, gamma, inverse Gaussian and Burr. This comparison was developed using experimental wind speed data relating to five Italian locations and a location in Colorado (USA) belonging to the National Renewable Energy Laboratory. For each location, the parameters of each PDF were obtained with the least squares non-linear regression method. The results of the comparisons, in terms of the coefficient of determination R2 and root mean square error (RMSE) for goodness of fit and in terms of relative error in the calculation of the statistical quantities, show that the use of the MTTND gives rise to greater accuracy than a conventional wind speed PDF.

Abstract The Ria de Muros is a large coastal embayment on the north-western coast of Spain in which the peak tidal currents exceed 2 m/s. It is therefore a promising site for tidal stream power. The key point when assessing this resource is the accurate estimation of the tidal currents. In this work a finite difference numerical model is used for this purpose. The model solves the vertically integrated Navier–Stokes hydrodynamics and transport equations. It is validated with in situ velocity measurements performed by means of an acoustic Doppler current profiler (ADCP). Thereafter the tidal flow velocities and the corresponding power densities are computed. The largest values are found in a section of the inner ria, in which two points are selected for a detailed assessment of the resource. The model is then run to compute the tidal stream and the corresponding power density at these points during a 14-day period, so as to cover the spring–neap cycle. The power density curve thus obtained is numerically integrated to compute the annual energy output that can be obtained by a tidal stream power plant at each location.

Although considered a current highlight, the concept of intelligent buildings (IB) has not been adopted as quickly and widely as expected. One of the reasons for this is the lack of information and knowledge support to all professionals involved at the design stage of a project. This paper provides a brief overview on the new advances of IB technologies and discusses ways of supplementing the decision making process by adopting two methods for economical and technical aspects of IB applications. It goes on to introduce an on-going research which aims to utilise knowledge based systems to provide comprehensive evaluations to alternatives and decision support to retrofit building projects, when they are being conceptualised.

Abstract Reliability analysis of IESs (Integrated Energy System) is complicated because of the complexity of system topology and dynamics and different kinds of uncertainties. Reliability is often calculated based on statistic methods, which always focus on historical performances and neglect the importance of their dynamics and structure. To overcome this problem, in this paper, a systematic framework for dynamically analysing the real-time reliability of IESs is proposed by integrating different machine learning methods and statistics. Firstly, the bootstrap-based Extreme Learning Machine is developed to forecast the conditional probability distributions of the productions of renewable energies and the energy consumptions. Then, the dynamic behaviour of IESs is simulated based on a stacked auto-encoder model, instead of using traditional mechanism-based simulation models, for improving computational efficiency. Besides, the variables representing the transient properties of natural gas pipeline networks, such as delivery pressures and flow rates, are taken as the indicators for quantifying the energy supply security in natural gas pipeline networks. The time-dependent relationships among these indicators and their statistic correlations are modelled for improving the effectiveness of the analysis results. Finally, the reliability assessment is performed by estimating the probability distribution of each functional state of the target IES. A case study of a realistic bi-directional IES is carried out to demonstrate the effectiveness of the proposed method. The results show that the method is able to effectively evaluate the reliability of IESs, which can provide useful information for system operation and management.

Access to a reliable source of electricity is a basic need for any community as it can improve the living standards characterized via the improvement of healthcare, education, and the local economy at large. There are two key factors to consider when assessing the appropriateness of a micro-grid system, the cost-effectiveness of the system and the quality of service. The tradeoff between cost and reliability of the system is a major compromise in designing hybrid systems. In this way, optimization of a Hybrid Micro-Grid System (HMGS) is investigated. A hybrid wind/PV system with battery storage and diesel generator is used for this purpose. The power management algorithm is applied to the load, and the Multi-Objective Particle Swarm Optimization (MOPSO) method is used to find the best configuration of the system and for sizing the components. A set of recent hourly wind speed data from three meteorological stations in Iran, namely: Nahavand, Rafsanjan, and Khash, are selected and tested for the optimization of HMGS. Despite design complexity of the aforementioned systems, the results show that the MOPSO optimization model produces appropriate sizing of the components for each location. It is also suggested that the use of HMGS can be considered as a good alternative to promote electrification projects and enhance energy access within remote Iranian areas or other developing countries enjoying the same or similar climatic conditions.

Some simplified correlations of mean hourly global and diffuse luminous efficacy on the horizontal plane for all sky conditions have been obtained for Arcavacata di Rende (Italy) and have been compared with other literature models and other experimental data measured in Geneva (Switzerland), Vaulx-en-Velin (France), Bratislava (Slovakia) and Osaka (Japan). The comparisons show that, for global efficacy, the differences among the various models are not significant, and the use of a model with a constant value of efficacy gives good predictions of global illuminance. For the prediction of diffuse illuminance the differences among the models are larger, but the use of a constant diffuse efficacy provides a good first estimate of diffuse illuminance.

Abstract The authors show an application of the multicriteria decision-making methodology used to assess an action plan for the diffusion of renewable energy technologies at regional scale. This methodological tool gives the decision-maker considerable help in the selection of the most suitable innovative technologies in the energy sector, according to preliminary fixed objectives. In this paper, a case study is carried out for the island of Sardinia. This region presents, on one hand, a high potential for energy resources exploitation, but on the other hand, it represents a specific case among other Italian regions, because of its socio-economic status and history. Three decision scenarios have been supposed, each one representing a coherent set of actions, on the basis of which strategies of diffusion are developed.

Abstract The standard EN 12975-2 provides guidelines for testing solar collectors both in stationary and quasi-dynamic conditions. The second test method allows the optical efficiency of flat-plate collectors and even evacuated tube collectors to be determined by applying the extended multiple linear regression. However, in the case of tubular shape collectors, the available procedure requires a large number of data, above all for the determination of the transversal incidence angle modifier, which is the parameter describing the optical response of the absorber tube to the direct beam on the plane normal to the tube axis. Here, an improved procedure to determine the transversal incidence angle modifier is presented and validated against experimental data. For this purpose, efficiency tests in quasi-dynamic conditions have been performed following the standard EN 12975-2 on a U-tube evacuated tubular collector, using a cylindrical absorber, both with and without external CPC (compound parabolic concentrator) reflectors. The validation has been performed by comparing the efficiency curve and the curve of incidence angle modifier to the ones that are obtained by means of other available methods. The main advantages of the present new procedure are the followings: it provides a continuous curve of the incidence angle modifier and it does not require to subdivide the incidence angle range in many intervals. Therefore, it does not require a minimum number of data points for each data subset and thus it is less demanding in terms of required number of tests.